HP Lp1965 User Guide

ENWW
3  Setting Up the Monitor 
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other 
attached devices, then follow the instructions below. 
NOTE  Be sure the master power switch,  located on the rear panel of the monitor, is in the off 
position. The master power switch turns off all power to the monitor. 
Installing the Monitor Pedestal Base
 
NOTE  Do not install the pedestal base if the monitor  will be used on a wall, swing arm, or 
other mounting...

ENWW
Rear Components
 
Figure 3-2 Rear Components 
Component Function 
1 Cable Lock Provision Provides slot for use with cable security locks. 
2 Master Power Switch Turns off all power to the monitor. 
3 AC Power Connector Connects the AC power cord to the monitor. 
4 DVI-I Connectors Connects the DVI-I to VGA signal cable or DVI-D signal 
cable to the monitor. 
5 USB Upstream Connector Connects the monitor USB hub to a host USB port/hub. 
6 USB Downstream Connectors Connects optional USB devices to...

ENWW
Selecting the Signal Connectors and Cables 
The monitor features two DVI-I connectors capable of supporting either analog or digital input. 
The video mode supported by the DVI-I connector  is determined by the video cable used. 
●	 
Figure 3-3   Connecting the DVI-I to VGA Signal Cable 
Figure 3-4  Connecting the DVI-D Signal Cable 
Selecting the Signal Connectors and Cables  7 
 

ENWW
Connecting the Monitor 
Figure 3-5 Connecting the USB Cable 
WARNING!  To reduce the risk of electric shock or damage to the equipment: 
• 
 

ENWW
Figure 3-6 Connecting the Power Cable 
Figure 3-7  Using the Cable Management Feature 
Connecting the Monitor  9 
 

ENWW
Adjusting the Monitor 
1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level. 
Figure 3-8  Tilting the Monitor 
NOTE The 24" model has a tilt range of -5 to +25 degrees. 
2.  Swivel the monitor to the left or right for the best viewing angle. 
Figure 3-9  Swiveling the Monitor 
10  Chapter 3   Setting Up the Monitor 
 

ENWW
3. Adjust the monitor's height so that it is  parallel to your eye height for a comfortable viewing 
position. 
WARNING!  A lock-down/release button on the front of the column prevents the display 
head of the 19" model from sliding up when  the monitor is lifted. If the display head is 
locked in the lowest height position: 
Figure 3-10   Adjusting the Height (LP2065 and LP2465 models) 
NOTE The 19" model has a height adjustment range of 100 mm. 
Adjusting the Monitor  11 
 

ENWW
4. Pivot the monitor from landscape to portrait orientation viewing to adapt to your application. 
Figure 3-11   Pivoting the Monitor 
NOTE The 20" model (shown above) pivots counter-clockwise; the 19" and 24" models 
pivot clockwise. 
To view information on the screen in portrait mode, you will need to install the Pivot Pro 
software included on the software and documentation CD. 
Turning on the Monitor 
CAUTION  Burn-in image damage may occur on monitors that display the same static...

ENWW
Connecting USB Devices 
The monitor provides four USB connectors, two on the side panel and two on the rear panel, used to 
connect devices such as a digital camera, USB keyboard, or USB mouse. 
NOTE You must connect the USB hub cable from  the monitor to the computer to enable the 
USB 2.0 ports on the monitor.  Refer to Step 2 in Connecting the Monitor . 
Figure 3-12 Connecting USB Devices 
Connecting USB Devices  13 
 

ENWW
Using the Accessory Rails 
The monitor features accessory rails on the rear that may be used to mount optional devices, such 
as the HP speaker bar, to attach to the  LCD. Refer to the documentation included with the optional 
device for detailed mounting instructions. 
Figure 3-13   Using the Accessory Rails Feature 
Removing the Monitor Pedestal Base 
You can remove the monitor panel from the pedestal base to mount the panel on a wall, a swing 
arm, or other mounting fixture. 
This monitor has a...