HP Le2201w User Guide

							
Adjusting the Monitor Settings
The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP Display
Assistant utility.
NOTE:If there is a problem with the display settings,  try resetting the settings to the factory defaults
by opening the OSD and selecting  Factory Reset from the OSD menu.
Using the On-Screen Display Menu
Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences. To
access the OSD, do the following:
1.If the monitor is not already on, press the  Power button to turn on the monitor.
2. To access the OSD Menu, press the  Menu button on the monitor’s front panel.
3. To navigate through the OSD Menu, press the  + (Plus) button on the monitor’s front panel to scroll
up, or the  – (Minus)/ Auto button to scroll in reverse.
4. To select an item from the OSD Menu, use the  + or  – buttons to scroll to and highlight your selection,
then press the  Menu button to select that function.
5. Adjust the item using the  + or  – buttons on the front pa nel to adjust the scale.
6. After adjusting the function, select  Save and Return, or Cancel  if you don’t want to save the setting,
then select  Exit from the Main Menu.
NOTE: If the buttons remain untouched for 10 seconds while displaying a menu, new adjustments will
be discarded and the settings will revert to previous settings and exit the menu.
ENWW Adjusting the Monitor Settings 15
 
						

							
OSD Menu Selections
The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions.
After changing an OSD menu item, and if the menu screen has these options, you may choose to:
● Cancel
—to return to the previous menu level.
● Save and Return
—to save all changes and return to the OSD Main Menu screen. This Save and
Return option is only active if you change a menu item.
Table 4-2   OSD Menu
IconMain MenuSubmenuDescription
BrightnessAdjustable scaleAdjusts the brightness level of the screen. The factory
default range is 90.
ContrastAdjustable scaleAdjusts the contrast level of the screen. The factory
default range is 80.
Volume (select
models with
internal speakers) Adjusts the monitors speaker volume level. The
factory default range is 50.
Image ControlAdjusts the screen image. (VGA input only)
Auto AdjustmentAutomatically adjusts the screen image.
Horizontal PositionAdjusts the position of the screen image left and right.
Vertical PositionAdjusts the position of the screen image up and down.
Custom Scaling (select
models)Selects the method on how displayed information on
the monitor will be formatted. Select:
●Fill to Screen - image fills the entire screen and
may look distorted or elongated because of non-
proportional scaling of height and width
● Fill to Aspect Ratio - image is sized to fit the
screen and maintains proportional image
● One-to-one (select models) - disables video
scaling, displays an image that is smaller in size
than the monitor’s capability and centers the
image on the screen in the active viewing area
Sharpness (select
models)Adjusts the screen image to look sharper or soft.
NOTE:
If the one-to-one custom scaling menu is
selected, scaling is disabled and the sharpness
feature will also be disabled.
ClockMinimizes any vertic al bars or strips visible on the
screen background. Adjusting the Clock will also
change the horizontal screen image.
Clock PhaseAdjusts the focus of the display. This adjustment
allows you to remove any  horizontal noise and clear or
sharpen the image of characters.
Color Selects the screen color. The factory default is 6500K or Custom Color, depending on the model.
16 Chapter 4   Operating the Monitor ENWW
 
						

							
IconMain MenuSubmenuDescription
9300 KChanges to slightly blueish white.
6500 KChanges to slightly reddish white.
Custom ColorSelects and adjusts your own color scales:
●R—sets your own red color levels
● G—sets your own green color levels
● B—sets your own blue color levels
sRGBSets your screen colors to adapt to the color standards
used in the image technology industry.
Quick View Select the viewing mode.
  MovieSelect the movie mode.
  PhotoSelect the photo mode.
  GamingSelect the gaming mode.
  TextSelect the text mode.
  CustomSettings saved when user adjusts the Brightness,
Contrast, or Color in one of the Quick View options.
LanguageSelects the language in which the OSD menu is
displayed. The factory default is English.
ManagementSelects the OSD and power management features of
the monitor.
 OSD ControlAdjusts the position of the OSD menu screen to:
●
Horizontal OSD Positi
on—Changes the viewing
position of the OSD menu to the left or right area
of the screen. The factory default range is 50.
● Vertical OSD Position—Changes the viewing
position of the OSD menu to the top or bottom
area of the screen. The factory default range is
50.
● OSD Transparency—Adjust to view the
background information through the OSD
● OSD Timeout—Sets the time duration in seconds
that the OSD is visible after the last button is
pressed. The factory default is 30 seconds.
● OSD Rotation (select models)—Rotates the OSD
Menu to support pivot function.
Power Saver Enables the power saving feature. Select:
●On
● Off
The factory default is On.
Table 4-2   OSD Menu (continued)
ENWW Adjusting the Monitor Settings 17
 
						

							
IconMain MenuSubmenuDescription
Power On RecallRestores power to the monitor following an
unexpected removal of power. Select:
●On
● Off
The factory default is On.
Mode DisplayDisplays the resolution, refresh rate and frequency
information on the screen each time the OSD Main
Menu is accessed. Select:
● On
● Off
Depending on monitor model, factory default is On or
Off.
Power-On Status
DisplayDisplays the operating status of the monitor each time
the monitor is powered on. Select the location to
display the status to:
● Top
● Middle
● Bottom
● Off
The factory default is Top.
DDC/CI SupportAllows the computer to control some OSD menu
features such as brightness, contrast and color
temperature. Set to:
● On
● Off
The factory default is On.
 Bezel Power LEDTurns off the power LED on the front panel of the
monitor. The factory default is On.
Sleep Timer Provides the timer adjustment menu options:
●Set Current Time—sets the current time in hours
and minutes
● Set Sleep Time—sets the time you want to place
the monitor in sleep mode
● Set on Time—sets the time you want the monitor
to wake up from sleep mode
● Timer—sets the Sleep Timer feature On or Off.
The default setting is Off.
● Sleep Now—immediately sets the monitor to
enter sleep mode
Table 4-2
  OSD Menu (continued)
18 Chapter 4   Operating the Monitor ENWW
 
						

							
IconMain MenuSubmenuDescription
Video Input
Control (select
models) Selects the video input signal. DVI is the factory
default.
 Switch Video InputSelects the other (VGA or DVI) video input signal.
Default is DVI.
 Auto-Switch InputTurns the systems automatic video signal input to on
or off. The factory default is On.
 Default Video InputSelects the default or primary video input signal when
the monitor is connected to two active and valid video
sources. The monitor will aut omatically determine the
video format. The default input selection is DVI.
Analog — VGA — Selects VGA input.
Digital — DVI — Selects DVI input.
InformationSelects and displays important information about the
monitor.
Current SettingsProvides the current input video mode.
Recommended
SettingsProvides the recommended resolution mode and
refresh rate for the monitor.
Serial NumberReports the serial number of the monitor. The serial
number is needed if contacting HP technical support.
VersionReports the firmware version of the monitor.
Backlight HoursReports the total hours of backlight operation.
  Service Support: http://
www.hp.com/support 
Factory ResetReturns all OSD menu settings and DDC/CI controls
to the factory default settings, except the Language.
Exit Exits the OSD menu screen.
Table 4-2   OSD Menu (continued)
ENWW Adjusting the Monitor Settings 19
 
						

							
Optimizing Digital Conversion
Two controls in the on-screen display can be adjusted to improve image performance: Clock and Clock
Phase.
NOTE:The Clock and Clock Phase controls are adjustable only when using an analog input. These
controls are not adjustab le for digital inputs.
The Clock must first be set correctly since the Clo ck Phase settings are dependent on the main Clock
setting. Use these controls only when the auto-adj ustment function does not provide a satisfactory
image.
● Clock
—Increases/decreases the value to minimize any vertical bars or stripes visible on the screen
background.
● Clock Phase
—Increases/decreases the value to mini mize video distortion or video jitter.
NOTE:When using the controls, you w ill obtain the best results by using the auto-adjustment pattern
software utility provided on the CD.
When adjusting the Clock and Clock Phase values, if the monitor images become distorted, continue
adjusting the values until the distortion disappears. To  restore the factory settings, select Yes from the
Factory Reset menu in the on-screen display.
Using the HP Displa y Assistant Utility
HP Display Assistant, included on  the software and documentation CD, is a soft ware utility that guides
you through the tuning process with easy to underst and instructions and background patterns designed
for each monitor control. It provides:
● Accurate screen calibration through the use of step
-by-step instruction Wizards to obtain the best
overall image quality.
● Software control of the monitor image and color settings to eliminate dependence on the monitor’s
front panel buttons and On-Screen Display (OSD) menu.
● Defined preset display settings for each individual user in a multi-user environment.
● Multiple preset display settin
gs for a single user based on content and ambient lighting.
● Asset Management and Powe
r Management capabilities that incl ude remote control for individual
or a group of displays on the domain  from a centralized console application.
The HP Display Assistant Utility has two modes of  operation: Wizard and OSD mode. The preferred
method of use is Wizard mode, wh ich takes you through a step-by-step process to accurately calibrate
the monitor. This method relies on a sequence of step s that will obtain the best display results when
completed.
NOTE: Refer to the HP Display Assistant user guide  for additional information about the software.
20 Chapter 4   Operating the Monitor ENWW
 
						

							
Identifying Monitor Conditions
Special messages will appear on the monitor screen when identifying the following monitor conditions:
● Input Signal Out of Range—Change resolution setting to 1440 x 900 – 60Hz
—Indicates the
monitor does not support the input signal because  the resolution and/or refresh rate are set higher
than the monitor supports (models LE190
1 w/LE190 1wm).

●Input Signal Out of Range—Change resolution setting to 1680 x 1050 – 60Hz
—Indicates the
monitor does not support the input signal because  the resolution and/or refresh rate are set higher
than the monitor supports (model LE220
1 w).

● No Input Signal
—Indicates the monitor is not receiving a  video signal from the PC on the monitor
video input connector. Check to determine if the PC  or input signal source is off or in the power
saving mode.
● Multiple Inputs are Active
—Use the OSD to select the desired video input —(select models)
Indicates the monitor is connected to two video in puts. The monitor is trying to display both inputs,
but after 10 seconds the monitor uses the default signal input.
● Auto Adjustment in Progress
—Indicates the auto-adjustment function is active.
● Monitor Going to Sleep
—Indicates the screen display is entering a sleep mode.
● Check Video Cable
—Indicates the video cable is not pr operly connected to the computer.
● OSD Lockout
—The OSD can be enabled or disabled by pressing and holding the  Menu button
on the front panel for 10 seconds. If the OSD is locked, the warning message  OSD Lockout
displays for ten seconds.
◦ If the OSD is locked, press and hold the 
Menu button for 10 seconds to unlock the OSD.
◦ If the OSD is unlocked, press and hold the 
Menu button for 10 seco nds to lock the OSD.
● Power Button Lockout
—Indicates the power button is lock ed. If the power button is locked, the
warning message  Power Button Lockout  displays.
◦ If the power button is locked, press and hold the power button for 10 seconds to unlock the
power button function.
◦ If the power button is unlocked, press and hold the power button for 10 seconds to lock out
the power button function.
Sleep Timer Mode
The Sleep Timer mode is an energy-saving feature that enables you to set a time for the monitor to
power on and off at the same time every day. This 
also extends the life of the backlight bulbs in the
monitor. The Sleep Timer has five settings:
● Set Current Time
● Set Sleep Time
● Set On Time
● Timer: On/Off
● Sleep Now
ENWW Identifying Monitor Conditions 21
 
						

							
To set the timer:
1.Press the  Menu button on the monitor front panel to display the  OSD Menu.
2. Scroll down and highlight  Management.
3. Press the  Menu button to select  Management.
4. Scroll down and highlight and select  Sleep Timer > Set Current Time.
NOTE:You must set the current local time  before you reset the time for Sleep Time or On
Time . Note that the time is displayed in a 24–hour clock format. For example, 1:15 p.m. is displayed
as 13 hours 15 minutes.
A power failure or loss of  power to the monitor will cause the timer to reset  to 00:00. If this occurs,
you will need to reset  the sleep timer mode.
5.Press the  Menu button once to enter the adjustment mode for hours.
6. Press the  - (Minus) or  + (Plus) button to adjust the hour.
7. Press the  Menu button again to enter the time for minutes.
8. Press the  - (Minus) or  + (Plus) button to adjust the minutes.
9. Press the  Menu button to lock in  the time chosen.
10. After setting the current time, the highlight automatically skips to  Set Sleep Time hours. Repeat
steps 6 through 9 to set  Sleep Time.
11. If you do not want to set  Sleep Time, press the Menu button twice, then select  Save and
Return  to exit the menu.
12. After setting  Sleep Time, the highlight automatically skips to  Set On Time hours. Repeat steps 6
through 9 to set  On Time.
13. Set the  Timer mode  to On to activate the  Sleep Timer settings.
14. When you are finished, select  Save and Return to exit the menu.
The fifth selection,  Sleep Now, turns the monitor backlights off immediately and stays in sleep mode
until the next  On Time activates or a monitor button is pressed.
22 Chapter 4   Operating the Monitor ENWW
 
						

							
HP Display LiteSaver
HP Display LiteSaver is a software application, available on the CD, that increases monitor life and
saves energy. It allows you to place the monitor into its low power sleep mode at predefined times by
shutting down or reducing power to most internal  circuits. This helps protect the LCD panel against
image retention. Image retention can occur when the monitor is left on while displaying the same image
for an extended period of time, leaving a shadow of the image on the screen.
Installing the HP Disp lay LiteSaver Software
1.Insert the CD in the computer CD-ROM Drive. The CD menu is displayed.
2. Select  Install HP Display LiteSaver Software .
3. After installing the  software, click the  HP Display LiteSaver  icon in the Windows system tray or
right-click the icon and select  Configure from the pop-up menu.
4. Select the following options to configure the HP Display LiteSaver features:
Table 4-3   HP Display LiteSaver Configuration Options
Select This OptionTo Do This
Enable Display LiteSaverEnables the HP Display Lite Saver functions; deselect to disable the HP Display
LiteSaver.
Display OffSets the time when the monitor automatically turns off. This does not affect screen
saver operation, which has priority  over the HP Display LiteSaver.
Display OnSets the time when the monitor automatically turns on. This does not affect screen
saver operation, which has priority over the HP Display LiteSaver.
Activity ExtensionSets the time in minutes before the monitor turns off if there is any keyboard or mouse
activity after the Display Off time is reac hed. If the keyboard or mouse is used, then
HP Display LiteSaver waits until the set amount of time before turning the display
off again. Set to 0 to disable. If disabled , the monitor will turn off as soon as the
Display Off time is reached, regardl ess of keyboard or mouse activity.
Show 1 minute Display Off NoticeDisplays a popup message in the system tr ay 1 minute before the monitor is turned
off by HP Display LiteSaver.
StatusShows the time until the monitor is next due to be turned off by HP Display LiteSaver.
OKStores the current settings and minimizes  HP Display LiteSaver to the System Tray.
CancelRestores the previous settings and minimizes HP Display LiteSaver to the System
Tray. HP Display LiteSaver will continue to run.
HelpOpens the online help file.
Exit Exits and closes the HP Display LiteSaver.  It will no longer control the monitor power
until it is next run.
View  HP Display LiteSaver Readme  on the CD for additional information on how to configure HP Display
LiteSaver.
ENWW HP Display LiteSaver 23
 
						

							
sRGB Support
The monitor is designed to support sRGB for color management, which adapts to the color standards
used in the image technology industry.
To take advantage of the sRGB support, yo u will need to change the monitor’s color temperature to
sRGB and install the sRGB color profile (ICM) file.
NOTE: The sRGB color temperature preset will improve the color accuracy of sRGB images on the
computer monitor, but some  color variation may still occur.
Changing the Color Temperature
1.Press the  Menu button on the front panel of the monitor to launch the  Main Menu of the OSD.
2. Select  Color.
3. Select  sRGB.
4. Select  Save and Return  to exit the menu.
Installing the sRGB IC M File for Microsoft Windows 2000 and Windows XP
NOTE:To complete the following procedure, you must be logged in as an administrator or a member
of the administrator’s group. If the computer is  connected to a network, network policy settings may
prevent you from completing this procedure. The sRGB ICM file does not support Windows 95 and
Windows NT operating systems.
1. Click the  Display icon in the  Control Panel.
2. In the  Display Properties  windows, select the  Settings tab, then click the  Advanced button.
3. Select the  Color Management  tab, then click the Add button to open the  Add Profile
Association  dialog box.
4. Select the  sRGB Color Space Profile.icm  file, then click the Add button
5. To activate a color profile for th e monitor, you must set it as the Default Monitor Profile. Select
sRGB Color Space Profile , then click Set as Default  button.
6. Click  Apply  or OK .
Installing the sRGB ICM File  for Microsoft Windows Vista
1.Click  Appearance and Personalization  icon in the Control Panel.
2. Click  Personalization .
3. Click  Display Settings .
4. Click the  Advanced Settings  button.
5. Click the  Color Management  tab, then click the Color Management  button.
6. Click the  Advanced  tab, then click the  Change System Defaults  button.
7. On the  Devices  tab, click the  Add button.
24 Chapter 4   Operating the Monitor ENWW