HP Le2201w User Guide

8.Select the RGB Color Space Prof ile.icm file, then click the OK button.
9. To activate a color profile for the monitor, you mu st set it as the Default Monitor Profile. Select
sRGB Color Space Profile , then click the Set as Default button.
ENWW sRGB Support 25
 

A Troubleshooting
Solving Common Problems
The following table lists possible problems, the possible cause of each problem, and the recommended
solutions.
ProblemPossible CauseSolution
Screen is blank.Power cord is disconnected.Connect the power cord.
Power button on front panel of
the monitor is turned off.Press the front panel power button.
NOTE: If pressing the power button has no effect,
press and hold the power button for 10 seconds to
disable the power button lockout feature.
Video cable is...

ProblemPossible CauseSolution
HP Display LiteSaver doesnt turn off
the monitor screen.The Activity Extension time
has not elapsed.The default Activity Extension value is set to 10
minutes. The HP Display Lite Saver will wait to detect
no input or movement from the keyboard or mouse
for 10 consecutive minutes after the Display Off time
has passed, before the monitor enters into low-
power mode. For example, if the Display Off time is
set to 5 minutes from the current time and the Activity
Extension is...

Online Technical Support
For the online access to technical support information, self-solve tools, online assistance, community
forums of IT experts, broad mu tlivendor knowledge base, monitoring and diagnostic tools, go to
http://www.hp.com/support
Preparing to Call Technical Support
If you cannot solve a problem using the trouble shoo ting tips in this section, you may need to call
technical support. Have the following information available when you call:
● The monitor
● Monitor model number
● Serial...

B Technical Specifications
NOTE:All performance specifications are provided  by the component manufacturers. Performance
specifications represent the highest specification of  all HPs component manufacturers typical level
specifications for performance and actual performance may vary either higher or lower.
LE1901w Model
Table B-1   LE1901w Specifications
Display
Type48.3 cm wide screen
TFT LCD19 inches wide screen
Viewable Image Size48.3 cm diagonal19–inch diagonal
Tilt-5 to 25°
Maximum Weight...

Storage0 to 12192 m0 to 40,000 feet
Power Consumption (maximum)

LE2201w Model
Table B-3  LE2201w Specifications
Display
Type55.9 cm wide screen
TFT LCD22 inches wide screen
Viewable Image Size55.9 cm diagonal22–inch diagonal
Tilt-5 to 20°
Maximum Weight (Unpacked)4.7 kg10.31 lbs.
Dimensions (include base)
Height
Depth
Width
41.5 cm
20.7 cm
51.5 cm16.3 inches
8.1 inches
20.3 inches
Maximum Graphic Resolution1680 x 1050 (60Hz)
Optimum Graphic Resolution1680 x 1050 (60Hz) 
Text Mode720 × 400
Dot Pitch0.282 (H) × 0.282 (W) mm
Horizontal Frequency24 to 83 kHz
Vertical...

Recognizing Preset Display Resolutions
The display resolutions listed below are the most commonly used modes and are set as factory defaults.
This monitor automatically recognized these preset modes a nd they will appear properly sized and
centered on the screen.
LE1901w/LE1901wm Models
Table B-4   Factory Preset Modes
PresetPixel FormatHorz Freq (kHz)Vert Freq (Hz)
1640 × 48031.559.9
2640 × 48037.575.0
3720 × 40031.570.1
4800 × 60037.960.3
5800 × 60046.975.0
6832 × 62449.774.6
71024 × 76848.460.0
81024...

101152 x 90061.866.0
111280 x 76847.460.0
121280 × 96060.060.0
131280 × 102464.060.0
141280 × 102480.075.0
151440 x 90055.959.9
161600 x 100061.660.0
17 1680 x 1050 65.3 60.0
Entering User Modes
The video controller signal may occasionally call for a mode that is not preset if:
●You are not using a stand
ard graphics adapter.
● You are not using a preset mode.
It this occurs, you may need to readjust the param eters of the monitor screen by using the on-screen
display. Your changes can be made to any or...

C Agency Regulatory Notices
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in  accordance with the instructions, may cause harmful
interference to radio...