HP Le2002xm User Guide

							Connecting the Cables
1.Place the monitor in a convenient, well-ventilated location near the computer.
2.Remove the cable management clip from the pedestal by pulling outward on the two sides of the
clip (1) then lifting the clip off the pedestal (2).
Figure 2-3  Removing the Cable Management Clip
3.Connect a VGA signal cable or DVI-D signal cable (select models).
NOTE:The monitor is capable of supporting either analog or digital input (select models). The
video mode is determined by the video cable used. The monitor will automatically determine
which inputs have valid video signals. The inputs can be selected by pressing the +/source
button on the front panel or through the On-Screen Display (OSD) feature by pressing the Menu
button.
●For analog operation, use the VGA signal cable provided. Connect the VGA signal cable to
the VGA connector on the rear of the monitor and the other end to the VGA connector on
the computer.
●For DVI digital operation, use the DVI-D signal cable provided. Connect the DVI-D signal
cable to the DVI connector on the rear of the monitor and the other end to the DVI
connector on the computer.
4.Connect one end of the provided audio cable to the audio connector on the monitor and connect
the other end of the cable to an audio output connector on the rear panel of the computer (select
models).
ENWWConnecting the Cables 5
 
						

							5.Connect one end of the power cord to the AC power connector on the back of the monitor, and
the other end to an electrical wall outlet.
Figure 2-4  Connecting the Cables
WARNING!To reduce the risk of electric shock or damage to the equipment:
Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
For your safety, do not place anything on power cords or cables. Arrange them so that no one
may accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from
the electrical outlet, grasp the cord by the plug.
6.Secure the cables in place with the cable management clip. Press the clip straight down on the
curved neck of the pedestal ensuring that the tabs on the sides of the clip snap into the slots on
the pedestal.
Figure 2-5  Installing the Cable Management Clip
6 Chapter 2   Setting Up the Monitor ENWW
 
						

							Front Panel Controls
Figure 2-6  Monitor Front Panel Controls
Table 2-1  Monitor Front Panel Controls
Control Function
1
Menu Opens, selects or exits the OSD menu.
2
Minus If the OSD menu is on, press to navigate backward through
the OSD menu and decrease adjustment levels.
If the OSD menu is inactive, press to activate the volume
adjustment bar. Press - or + to adjust the volume (select
models).
3
Plus/source If the OSD menu is on, press to navigate forward through
the OSD menu and increase adjustment levels.
If the OSD menu is inactive, press to activate the source
button that chooses the video signal input (VGA or DVI).
4
OK/auto If the OSD menu is on, press to select the highlighted
menu item.
If the OSD menu is inactive, press to activate the auto
adjustment feature to optimize the screen image.
5
Power Turns the monitor on or off.
6   Power LED Blue = Fully powered.
Amber = Sleep mode.
Flashing Amber = Sleep Timer mode.
NOTE:To view an OSD menu simulator, visit the HP Customer Self Repair Services Media Library
at 
http://www.hp.com/go/sml.
ENWWFront Panel Controls 7
 
						

							Adjusting the Monitor
Tilt the monitors panel forward or backward to set it to a comfortable eye level.
Figure 2-7  Tilting the Monitor
Turning on the Monitor
1.Press the power button on the computer to turn it on.
2.Press the power button on the front of the monitor to turn it on.
CAUTION:Burn-in image damage may occur on monitors that display the same static image on
screen for a prolonged period of time.* To avoid burn-in image damage on the monitor screen, you
should always activate a screen saver application or turn off the monitor when it is not in use for a
prolonged period of time. Image retention is a condition that may occur on all LCD screens. Monitors
with a “burned-in image” are not covered under the HP warranty.
* A prolonged period of time is 12 consecutive hours of non-use.
NOTE:If pressing the power button has no effect, the Power Button Lockout feature may be
enabled. To disable this feature, press and hold the monitor power button for 10 seconds.
NOTE:You can disable the power LED in the OSD menu. Press the Menu button on the front of the
monitor, then select Management > Bezel Power LED > Off.
When the monitor is powered on, a Monitor Status message is displayed for five seconds. The
message shows which input (DVI or VGA) is the current active signal, the status of the auto-switch
source setting (On or Off; factory default is On), the default source signal (factory default is VGA), the
current preset display resolution, and the recommended preset display resolution.
The monitor automatically scans the signal inputs for an active input and uses that input for the
display. If two or more inputs are active, the monitor will display the default input source. If the default
source is not one of the active inputs, then the monitor will display the highest ranking priority input in
the following order: DVI then VGA. You can change the default source in the OSD by pressing the
front panel Menu button and selecting Source Control > Default Source.
8 Chapter 2   Setting Up the Monitor ENWW
 
						

							Removing the Monitor Pedestal Base
You can remove the monitor panel from the pedestal base to install the panel on a wall, a swing arm,
or other mounting fixture.
CAUTION:Before beginning to disassemble the monitor, be sure the monitor is turned off and the
power and signal cables are both disconnected.
1.Disconnect and remove the signal and power cables from the monitor.
2.Lay the monitor face down on a flat surface covered by a clean, dry cloth.
3.Remove the four pedestal neck screws (1) and lift the pedestal neck (2) off of the monitor panel.
Figure 2-8  Removing the Pedestal Neck Screws
Mounting the Monitor
The monitor panel can be attached to a wall, swing arm, or other mounting fixture.
NOTE:This apparatus is intended to be supported by UL or CSA Listed wall mount bracket.
1.Remove the monitor panel from the pedestal base. Refer to Removing the Monitor Pedestal
Base on page 9.
CAUTION:This monitor supports the VESA industry standard 100 mm mounting holes. To
attach a third-party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long
screws are required. Longer screws must not be used because they may damage the monitor. It
is important to verify that the manufacturer’s mounting solution is compliant with the VESA
standard and is rated to support the weight of the monitor display panel. For best performance, it
is important to use the power and video cables provided with the monitor.
ENWW Removing the Monitor Pedestal Base 9
 
						

							2.To attach the monitor to a swing arm, insert four 10mm screws through the holes on the swing
arm plate and into the mounting holes on the monitor.
Figure 2-9  Mounting the Monitor
To attach the monitor to other mounting fixtures, follow the instructions included with the
mounting fixture to ensure that the monitor is safely attached.
3.Reconnect the cables to the monitor panel.
Installing a Cable Lock
You can secure the monitor to a fixed object with an optional cable lock available from HP.
Figure 2-10  Installing a Cable Lock
10 Chapter 2   Setting Up the Monitor ENWW
 
						

							3 Finding More Information
Refer to the HP LCD Monitors Reference Guide included on the CD with your monitor for additional
information on:
●Optimizing monitor performance
●Safety and maintenance guidelines
●Installing software from the CD
●Using the OSD menu
●Downloading software from the Web
For additional information on using and adjusting your monitor, go to 
http://www.hp.com/support.
Select your country or region, select Product Support & Troubleshooting, and then enter your monitor
model in the SEARCH window.
ENWW11
 
						

							4 Technical Specifications
NOTE:All specifications represent the typical specifications provided by HPs component
manufacturers; actual performance may vary either higher or lower.
LE1902x Model
Table 4-1  LE1902x Specifications
Maximum Weight (Unpacked) 2.8 kg 6.17 lbs
Dimensions (include base)
Height
Depth
Width33.89 cm
12.6 cm
44.93 cm13.34 inches
4.96 inches
17.69 inches
Maximum Graphic Resolution1366 x 768 (60 Hz) analog input
1366 x 768 (60 Hz) digital input
Optimum Graphic Resolution 1600 x 900 (60 Hz) analog input
1600 x 900 (60 Hz) digital input 
Power Source 100 – 240 VAC 50/60 Hz  
Input Terminal One VGA connector with cable included  
LE2002x and LE2002xm Models
Table 4-2  LE2002x and LE2002xm Specifications
Maximum Weight (Unpacked) 3.5 kg 7.7 lbs
Dimensions (include base)
Height
Depth
Width35.92 cm
15.11 cm
48.20 cm14.14 inches
5.95 inches
18.98 inches
Maximum Graphic Resolution 1600 x 900 (60 Hz) analog input
1600 x 900 (60 Hz) digital input
Optimum Graphic Resolution 1600 x 900 (60 Hz) analog input
1600 x 900 (60 Hz) digital input 
Power Source 100 – 240 VAC 50/60 Hz  
Input Terminal One VGA connector with cable included;
one DVI connector (cable not included
with LE2002x); one audio connector with
cable included (LE2002xm only) 
12 Chapter 4   Technical Specifications ENWW
 
						

							LE2202x Model
Table 4-3  LE2202x Specifications
Maximum Weight (Unpacked) 3.6 kg 7.94 lbs
Dimensions (include base)
Height
Depth
Width37.9 cm
16 cm
51.8 cm14.92 inches
6.3 inches
20.39 inches
Maximum Graphic Resolution 1920 x 1080 (60 Hz) analog input
1920 x 1080 (60 Hz) digital input
Optimum Graphic Resolution 1920 x 1080 (60 Hz) analog input
1920 x 1080 (60 Hz) digital input 
Power Source 100 – 240 VAC 50/60 Hz  
Input Terminal One VGA connector with cable included;
one DVI connector with cable included 
Recognizing Preset Display Resolutions
The display resolutions listed below are the most commonly used modes and are set as factory
defaults. This monitor automatically recognizes these preset modes and they will appear properly
sized and centered on the screen.
LE1902x Model
Table 4-4  Factory Preset Modes
Preset Pixel Format Horz Freq (kHz) Vert Freq (Hz)
1 640 × 480 31.469 59.94
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 960 60.0 60.0
6 1280 × 1024 63.98 60.02
7 1366 × 768 47.712 59.79
LE2002x and LE2002xm Models
Table 4-5  Factory Preset Modes
Preset Pixel Format Horz Freq (kHz) Vert Freq (Hz)
1 640 × 480 31.469 59.940
ENWWLE2202x Model 13
 
						

							Table 4-5  Factory Preset Modes (continued)
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.00 59.94
6 1280 × 1024 63.981 60.02
7 1440 × 900 55.935 59.887
8 1600 × 900 55.935 59.887
LE2202x Model
Table 4-6  Factory Preset Modes
Preset Pixel Format Horz Freq (kHz) Vert Freq (Hz)
1 640 × 480 31.469 59.940
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.00 60.00
6 1280 × 1024 63.981 60.02
7 1440 × 900 55.94 59.89
8 1680 × 1050 65.29 60.0
9 1920 × 1080 67.5 60.00
Entering User Modes
The video controller signal may occasionally call for a mode that is not preset if:
●You are not using a standard graphics adapter.
●You are not using a preset mode.
It this occurs, you may need to readjust the parameters of the monitor screen by using the on-screen
display. Your changes can be made to any or all of these modes and saved in memory. The monitor
automatically stores the new setting, then recognizes the new mode just as it does a preset mode. In
addition to the factory preset modes, there are at least 10 user modes that can be entered and
stored.
Energy Saver Feature
The monitors support a reduced power state. The reduced power state will be entered into if the
monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal. Upon
detecting the absence of these signals, the monitor screen is blanked, the backlight is turned off, and
the power light is turned amber. When the monitor is in the reduced power state, the monitor will
14 Chapter 4   Technical Specifications ENWW