HP Le1901wi User Guide

2 Safety and Maintenance Guidelines
Important Safety Information
A power cord is included with the monitor. If another cord is used, use only a power source and
connection appropriate for this monitor. For information on the correct power cord set to use with the
monitor, refer to 
Power Cord Set Requirements on page 43 in Appendix C.
WARNING!To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding feature. The grounding plug is an important safety...

not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS
or A) for each device.
●Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the
plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
●Turn the monitor off when not in use. You can substantially increase the life expectancy of the
monitor by using a screen saver program and turning off the monitor when not in use....

3 Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other
attached devices, then follow the instructions below.
Installing the Monitor on the Stand
CAUTION:Do not touch the surface of the LCD panel. Pressure on the panel may cause non-
uniformity of color or disorientation of the liquid crystals. If this occurs the screen will not recover to its
normal condition.
1.Place the monitor panel face down on a dry, soft cloth and connect the...

2.Place the stand on a desktop or table and push the neck on the stand down to its lowest position.
Slide the monitor all the way onto the stand so that the Quick Release mounting device emits an
audible click and is locked in place.
Figure 3-2  Installing the Monitor on the Stand
3.Route the monitor VGA and power cables through the cable guides at the bottom corners of the
mounting panel (select models).
Figure 3-3  Routing Monitor VGA and Power Cables
4.To install an HP USDT computer on the rear of the...

Installing an HP Ultra-slim Desktop (USDT) on the Stand
You can install an HP USDT or Thin Client computer on the rear side of the stand. This section provides
instructions on installing the USDT.
1.On the rear of the stand, remove the two screws (1) from the top of the computer mounting bracket
and lift the bracket off the stand (2).
Figure 3-4  Removing the Computer Mounting Bracket
ENWW Installing an HP Ultra-slim Desktop (USDT) on the Stand 7
 

2.Use the four screws provided to install the computer mounting bracket on the USDT computer.
NOTE:There are two sets of screw holes on the computer mounting bracket. Use the four holes
that are offset to install the USDT.
Be sure to install the computer mounting bracket on the USDT so that the rear ports on the USDT
are toward the right when viewed from the rear of the monitor stand. (The rear ports should be
toward the left when viewed from the front of the monitor.)
Figure 3-5  Installing the Computer...

cables), up through the bottom hole of the USDT computers port cover (1) and then connect the
cables to the rear of the computer (2).
5.Plug the computer and monitor power cables into an electrical wall outlet (3).
Figure 3-7  Connecting the Cables
6.Insert the hooks on the port cover into the slots on the rear of the USDT chassis and slide the port
cover down so that it locks in place.
Figure 3-8  Installing the Port Cover
ENWW Installing an HP Ultra-slim Desktop (USDT) on the Stand 9
 

7.Slide the power supply tray out from the base of the stand (1) and place the USDT power supply
into the tray (2). Route any loose cables through the cables guides on the sides of the tray (3).
Figure 3-9  Installing the Power Supply
8.Be sure the final configuration has the USDT properly oriented, as shown in the illustration below.
Figure 3-10  Proper Assembly of Integrated Work Center
WARNING!To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding...

Installing an HP Thin Client on the Stand
You can install an HP USDT or Thin Client computer on the rear side of the stand. This section provides
instructions on installing the Thin Client.
1.On the rear of the stand, remove the two screws (1) from the top of the computer mounting bracket
and lift the bracket off the stand (2).
Figure 3-11  Removing the Computer Mounting Bracket
2.Remove the HP logo panel from the right side of the Thin Client to access the screw holes for the
computer mounting bracket....

3.Use the four screws provided to install the computer mounting bracket on the Thin Client computer.
NOTE:There are two sets of screw holes on the computer mounting bracket. Use the four holes
that are centered on the bracket to install the Thin Client.
Be sure to install the computer mounting bracket on the Thin Client so that the rear ports on the
Thin Client are facing down and the feet on the Thin Client are facing outwards.
Figure 3-13  Installing the Computer Mounting Bracket on the Thin Client...