HP LaserJet P3005 User Manual

Specks might appear on a page after a jam has been cleared.
1.Print a few more pages to see if  the problem corrects itself.
2. Clean the inside of the device and run a cleaning page to clean the fuser. (See 
Clean the paper
path.)
3. Try using a different type of media.
4. Check the print cartridge for leaks. If th e print cartridge is leaking, replace it.
Dropouts 
1.Make sure that the environmental specifications for the device are being met. (See Operating
environment .)
2. If the media is rough,...

Gray background  
1.Do not use media that has already been run through the device.
2. Try using a different type of media.
3. Print a few more pages to see if the problem corrects itself.
4. Turn over the media in the tray. Also, try rotating the media 180°.
5. Open the  CONFIGURE DEVICE  menu at the device control panel. On the  PRINT QUALITY
submenu, increase the  TONER DENSITY setting. See 
Print Quality submenu .
6. Make sure that the environmental specific ations for the device are being met. (See...

Loose toner 
Loose toner, in this context, is defined as toner that can be rubbed off the page.
1. If media is heavy or rough, open the  CONFIGURE DEVICE menu at the device control panel. On
the  PRINT QUALITY  submenu, select  FUSER MODES, and then select the media type you are
using. Change the setting to  HIGH1 or HIGH2 , which helps the toner fuse more completely onto
the media. (See 
Print Quality submenu .) You must also set the type of media for the tray you are
using. (See 
Control print jobs...

Repeat image
Dear Mr. Abhjerhjk,The dhjhfiuhu if teint hhkjhjnf j us a weue jd, fnk
ksneh vnk kjdfkaakd ss hsjhnckkajhdhf kashfhnduujdn.
Pkshkkhklhlkhkhyufwe4yrh9jjflkln djd skshkshdcnksnjcnal
aksnclnslskjlncsl nas lnslna, ncnsljsjscljckn nsnclknsllj
hwlsdknls nwljs nlnscl nijhsn clsncij hn. Iosi fsjs jlkh andjna this
is a hn. jns fir stie a djakjd ajjssk. Thsi ius vnvlu tyeh lch afted,
and when hghj hgjhk jdj a dt sonnleh.
Suolklv jsdj hvjkrt ten sutc of jthjkfjkn vjdj hwjd, an olk d
.at fhjdjht...

5.Make sure that the type and quality of the medi a you are using meet HP specifications. (See Media
considerations.)
6. Make sure that the environmental specifications for the device are being met. (See 
Operating
environment .)
Curl or wave 
1.Turn over the media in the tray. Also, try rotating the media 180°.
2. Make sure that the type and quality of the medi a you are using meet HP specifications. (See 
Media
considerations.)
3. Make sure that the environmental specifications for the device are...

If the above actions do not improve wrinkles or creases, change your fuser mode from NORMAL to
LOW1 .
1. On the control panel, press  Menu.
2. Use 
 to highlight  CONFIGURE DEVICE , and then press .
3. Use 
 to highlight  PRINT QUALITY , and then press .
4. Use 
 to highlight  FUSER MODES , and then press .
5. Use 
 to highlight  LOW1, and then press .
Vertical white lines  
1.Print a few more pages to see if the problem corrects itself.
2. Make sure that the type and quality of the media you are using...

White spots on black 
1.Print a few more pages to see if  the problem corrects itself.
2. Make sure that the type and quality of the medi a you are using meet HP specifications. (See 
Media
considerations.)
3. Make sure that the environmental specifications for the device are being met. (See 
Operating
environment .)
4. Replace the print cartridge.
Scattered lines 
1.Make sure that the type and quality of the medi a you are using meet HP specifications. (See Media
considerations.)
2. Make sure that the...

Blurred print 
1.Make sure that the type and quality of the media you are using meet HP specifications. (See Media
considerations .)
2. Make sure that the environmental specific ations for the device are being met. (See 
Operating
environment.)
3. Turn over the media in the tray. Also, try rotating the media 180°.
4. Do not use media that already has been run through the device.
5. Decrease the toner density. Open the  CONFIGURE DEVICE menu at the device control panel.
Open the  PRINT QUALITY  submenu...

●From your software program, rotate the whole page 180° to print the lighter image first.
● If the defect occurs later in a print job, turn the 
device off for 10 minutes, and then turn it on to
restart the print job.
ENWW Solve print-quality problems 147
 

Solve network print problems
NOTEHP recommends that you use the device CD to install and set up the device on a
network.
● Print a configuration page (see Use information pages
). If an HP Jetdirect print server is installed,
printing a configuration page also prints a second  page that shows the network settings and status.
● See the 
HP Jetdirect Embedded Print  Server Administrators Guide on the device CD for help and
for more information about the Jetdirect configuration page. To open the guide, run...