HP Laserjet 5000 N Manual

18  Getting Started Guide EN
Step 11. Connect Printer Cables
The HP LaserJet 5000 printer includes an accessory connector and 
two interface ports: an IEEE-1284 parallel and an RS-232C serial 
port.
The HP LaserJet 5000 N and 5000 GN printers also include an 
HP JetDirect 600N print server card with an additional three ports: 
LocalTalk, Ethernet 10Base-T (RJ-45), and 10Base2 (BNC).
Figure 7 Interface Ports
LocalTalk 
cable and port10Base-T cable 
and RJ-45 port
ThinLAN cable 
and BNC portAccessory port...

ENGetting Started Guide   19
Connecting Parallel Cable
To ensure reliability, use an IEEE-1284 
bi-directional parallel cable. (These 
cables are clearly marked with 
“IEEE-1284.”) Only IEEE-1284 cables 
support all of the printer’s advanced 
features.
Caution
Make sure the printer is turned off.
1Connect the parallel cable to the 
parallel port. 
2Snap the wire clips in place to 
secure the cable to the printer.
The cable should install easily. If 
installation is difficult, check the 
cable...

20  Getting Started Guide EN
Connecting Serial Cable
If you are connecting the printer with 
the serial port, follow these 
instructions.
Caution
Make sure the printer is turned off 
before connecting the serial cable.
Caution
Do not connect a serial cable to the 
accessory port.
1Connect the serial cable to the serial 
port. 
The cable should install easily. If 
installation is difficult, check the 
cable orientation.
2Lock the serial cable into place with 
the two cable screws.
Connect the other end of...

ENGetting Started Guide   21
Connecting to Apple LocalTalk Network
Use the LocalTalk port to connect to an 
Apple LocalTalk network. (This port is 
only available on the HP LaserJet 
5000 N and 5000 GN printers.)
Caution
Make sure the printer is turned off 
before connecting to the LocalTalk 
port.
1Carefully check the orientation of 
the pins on the LocalTalk cable with 
the LocalTalk port.
2Connect the cable to the port. 
Connect the other end of the cable to 
the proper connector on the computer....

22  Getting Started Guide EN
Connecting to Ethernet 10Base-T Network 
Use the RJ-45 port to connect the printer to an Ethernet 10Base-T 
network. (This port is only available on the HP LaserJet 5000 N and 
5000 GN printers.)
CautionMake sure the printer is turned off before connecting to the RJ-45 
port.
NoteFor connection to a fast Ethernet (100Base-TX) network, an 
optional HP JetDirect 600N 10/100Base-TX print server is required. 
This card features a single RJ-45 port.
Figure 8   Connecting to...

ENGetting Started Guide   23
Connecting to Ethernet 10Base2 Network
Use the BNC port to connect the printer to an Ethernet 10Base2 
network. (This port is only available on the HP LaserJet 5000 N and 
5000 GN printers.)
CautionMake sure the printer is turned off before connecting to the BNC 
port.
Figure 9   Connecting to Ethernet 10Base2 Network
•Attach one section of your ThinLAN cable to the BNC “T”
 
connector. 
•Attach another ThinLAN cable section or a 50 Ohm terminator to 
the other side of the...

24  Getting Started Guide EN
Attaching an Accessory Connector
The accessory connector is used for adding optional paper handling 
(external input, output, and paper finishing) devices provided by 
HP-authorized hardware developers. For specific installation 
instructions, see the documentation provided with these products.
CautionMake sure the printer is turned off before connecting a device to the 
accessory connector.
CautionDo not connect the accessory cable to the serial port. 

ENGetting Started Guide   25
Step 12. Install Printing Software
The printer comes with printing software on a compact disc. The 
printer drivers on this compact disc must be installed to take full 
advantage of the printer features. If your computer does not have a 
CD-ROM drive but you have access to one, you can copy the 
compact disc onto diskettes for installation on your computer.
If you do not have access to a CD-ROM drive, a diskette is provided 
with the basic printer drivers. (The diskette does...

26  Getting Started Guide EN
Installing Windows Printing Software (CD)
For Windows 95 and Windows NT 4.0
1Close all running applications.
2Insert the compact disc into the CD-ROM drive. (Depending on 
the computer configuration, the installation program may 
automatically start.)
3Click 
Start.
4Click 
Run.
5Type 
D:\SETUP (or the appropriate drive directory letter) in the 
command line box and click 
OK.
6Follow the instructions on the computer screen.
For Windows 3.1x, Windows 3.11, and NT 3.5x1
1Close...

ENGetting Started Guide   27
Installing Macintosh Printing Software
1Quit all open applications.
2Insert the compact disc into the CD-ROM drive.
3Double-click the 
Installer icon and follow the instructions on the 
screen.
4Open the 
Chooser from the 
Apple menu.
5Click the 
Apple LaserWriter icon. If the icon is not there, contact 
your Macintosh dealer.
6If you are on a network with multiple zones, select the zone in the 
AppleTalk Zones box where the printer is located. If this is 
unknown, ask your...