HP La2006x User Guide
Have a look at the manual HP La2006x User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Removing the Monitor Pedestal Base You can remove the monitor panel from the pedestal base to install the panel on a wall, a swing arm, or other mounting fixture. NOTE:The following steps apply to the HP LA2006x, LA2206x, and LA2306x Models. CAUTION:Before beginning to disassemble the monitor, be sure the monitor is turned off and the power and signal cables are both disconnected. Also disconnect all USB cables connected to the monitor. 1.Disconnect and remove the signal, power, and USB cables from the monitor. 2.Lay the monitor face down on a flat surface covered by a clean, dry cloth. 3.Pivot the base 45 degrees clockwise and remove the screw from the back of the monitor, then pivot the base 45 degrees counter-clockwise and remove the other screw from the back of the monitor. Figure 2-16 Removing the Pedestal Base Screws 4.Rotate the base of the monitor up (1) then pull it back (2) to unhinge the tabs on the monitor stand from the slots in the monitor. Figure 2-17 Removing the Pedestal Base ENWWRemoving the Monitor Pedestal Base 15
Removing the Stand from the HP LA1956x Monitor You can remove the monitor panel from the monitor stand to attach the panel to a wall, a swing arm, or another mounting fixture. NOTE:The following steps apply only to the HP LA1956x Model. 1.Lay the monitor face down on a flat surface covered by a clean, dry cloth. 2.Remove the four screws from the monitor stand. Figure 2-18 Removing the Screws from the Monitor Stand 16 Chapter 2 Setting Up the Monitor ENWW
Mounting the Monitor The monitor panel can be attached to a wall, swing arm, or other mounting fixture. NOTE:This apparatus is intended to be supported by UL or CSA Listed wall mount bracket. 1.Remove the monitor panel from the pedestal base. Refer to Removing the Monitor Pedestal Base on page 15. CAUTION:This monitor supports the VESA industry standard 100 mm mounting holes. To attach a third-party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long screws are required. Longer screws must not be used because they may damage the monitor. It is important to verify that the manufacturer’s mounting solution is compliant with the VESA standard and is rated to support the weight of the monitor display panel. For best performance, it is important to use the power and video cables provided with the monitor. 2.To attach the monitor to a swing arm, insert four 10mm screws through the holes on the swing arm plate and into the mounting holes on the monitor. Figure 2-19 Mounting the Monitor To attach the monitor to other mounting fixtures, follow the instructions included with the mounting fixture to ensure that the monitor is safely attached. 3.Reconnect the cables to the monitor panel. ENWWRemoving the Monitor Pedestal Base 17
Locating the Rating Labels The rating labels on the monitor provide the spare part number, product number, and serial number. You may need these numbers when contacting HP about the monitor model. The rating labels are located on the rear panel of the monitor display head. Figure 2-20 Locating the Rating Labels Installing a Cable Lock You can secure the monitor to a fixed object with an optional cable lock available from HP. Figure 2-21 Installing a Cable Lock 18 Chapter 2 Setting Up the Monitor ENWW
3 Finding More Information Reference Guides Refer to the HP LCD Monitors Reference Guide included on the CD with your monitor for additional information on: ●Optimizing monitor performance ●Safety and maintenance guidelines ●Installing software from the CD ●Using the OSD menu ●Downloading software from the Web ●Agency regulatory information ●Troubleshooting and recommended solutions to common problems For information on theft deterrence, refer to the HP Display Assistant User Guide included on the CD with your monitor. Product Support For additional information on using and adjusting your monitor, go to http://www.hp.com/support. Select your country or region, select Product Support & Troubleshooting, and then enter your monitor model in the SEARCH window. NOTE:The monitor user guide, reference guide, and drivers are available at http://www.hp.com/ support. If the information provided in the guide or in the HP LCD Monitors Reference Guide do not address your questions, you can contact support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ●Chat online with an HP technician NOTE:When support chat is not available in a particular language, it is available in English. ●E-mail support ●Find support telephone numbers ●Locate an HP service center ENWWReference Guides 19
A Technical Specifications NOTE:All specifications represent the typical specifications provided by HPs component manufacturers; actual performance may vary either higher or lower. LA1956x Model Table A-1 LA1956x Specifications Display Type48.3 cm wide screen Twisted Nematic (TN) LED Backlit LCD19 inches wide screen Viewable Image Size 48.3 cm diagonal 19–inch diagonal Tilt -5 to 25° Swivel -180 to 180° Maximum Weight (Unpacked) 4.5 kg 9.92 lbs Dimensions (include base) Height (highest position) Height (lowest position) Depth Width48.64 cm 36.53 cm 19.21 cm 41.78 cm19.15 inches 14.38 inches 7.56 inches 16.45 inches Maximum Graphic Resolution 1280 x 1024 (60 Hz) Optimum Graphic Resolution 1280 x 1024 (60 Hz) Text Mode 720 × 400 Dot Pitch 0.294 (H) × 0.294 (W) mm Pixels Per Inch 91.8 PPI Horizontal Frequency 24 to 83 kHz Vertical Refresh Rate 50 to 76 Hz Environmental Requirements Temperature Operating Temperature Storage Temperature5 to 35° C -20 to 60° C41 to 95° F -4 to 140° F Relative Humidity 20 to 80% Power Source 100 – 240 VAC 50/60 Hz 20 Appendix A Technical Specifications ENWW
Table A-1 LA1956x Specifications (continued) Altitude: Operating Storage0 to 5000 m 0 to 12192 m0 to 16,400 feet 0 to 40,000 feet Measured Power Consumption: Full Power Typical Settings Energy Star® Test Methods Sleep Switch Off35.0 watts 27.0 watts
Table A-2 LA2006x Specifications (continued) Vertical Refresh Rate 50 to 76 Hz Environmental Requirements Temperature Operating Temperature Storage Temperature5 to 35° C -20 to 60° C41 to 95° F -4 to 140° F Relative Humidity 20 to 80% Power Source 100 – 240 VAC 50/60 Hz Altitude: Operating Storage0 to 5000 m 0 to 12192 m0 to 16,400 feet 0 to 40,000 feet Measured Power Consumption: Full Power Typical Settings Energy Star® Test Methods Sleep Switch Off34.0 watts 29.0 watts 24.5 watts 0.5 watts 0.5 watts Input Terminal One VGA connector with cable included; one DVI connector with cable included; one DisplayPort connector (cable not included) LA2206x Model Table A-3 LA2206x Specifications Display Type54.61 cm wide screen TFT LCD21.5 inches wide screen Viewable Image Size 54.61 cm diagonal 22–inch diagonal Tilt -5 to 30° Swivel -180 to 180° Maximum Weight (Unpacked) 6.0 kg 13.24 lbs Dimensions (include base) Height (highest position) Height (lowest position) Depth Width43.87 cm 33.35 cm 22.72 cm 51.8 cm17.27 inches 13.13 inches 8.94 inches 20.39 inches 22 Appendix A Technical Specifications ENWW
Table A-3 LA2206x Specifications (continued) Maximum Graphic Resolution 1920 x 1080 (60 Hz) analog input 1920 x 1080 (60 Hz) digital input Optimum Graphic Resolution 1920 x 1080 (60 Hz) analog input 1920 x 1080 (60 Hz) digital input Text Mode 720 x 400 Dot Pitch 0.248 (H) x 0.248 (W) mm Pixels Per Inch 102 PPI Horizontal Frequency 24 to 94 kHz Vertical Refresh Rate 50 to 76 Hz Environmental Requirements Temperature Operating Temperature Storage Temperature5 to 35° C -20 to 60° C41 to 95° F -4 to 140° F Relative Humidity 20 to 80% Power Source 100 – 240 VAC 50/60 Hz Altitude: Operating Storage0 to 5000 m 0 to 12192 m0 to 16,400 feet 0 to 40,000 feet Measured Power Consumption: Full Power Typical Settings Energy Star® Test Methods Sleep Switch Off38 watts 33 watts 25 watts 0.5 watts 0.5 watts Input Terminal One VGA connector with cable included; one DVI connector with cable included; one DisplayPort connector (cable not included) LA2306x Model Table A-4 LA2306x Specifications Display Type58.42 cm wide screen TFT LCD23 inches wide screen Viewable Image Size 58.42 cm diagonal 23–inch diagonal ENWWLA2306x Model 23
Table A-4 LA2306x Specifications (continued) Tilt -5 to 30° Swivel -180 to 180° Maximum Weight (Unpacked) 6.8 kg 15.0 lbs Dimensions (include base) Height (highest position) Height (lowest position) Depth Width46.62 cm 35.11 cm 24.95 cm 55.15 cm18.37 inches 13.83 inches 9.83 inches 21.73 inches Maximum Graphic Resolution 1920 x 1080 (60 Hz) analog input 1920 x 1080 (60 Hz) digital input Optimum Graphic Resolution 1920 x 1080 (60 Hz) analog input 1920 x 1080 (60 Hz) digital input Text Mode 720 × 400 Dot Pitch 0.265 (H) x 0.265 (W) mm Pixels Per Inch 95.8 PPI Horizontal Frequency 24 to 94 kHz Vertical Refresh Rate 50 to 76 Hz Environmental Requirements Temperature Operating Temperature Storage Temperature5 to 35° C -20 to 60° C41 to 95° F -4 to 140° F Relative Humidity 20 to 80% Power Source 100 – 240 VAC 50/60 Hz Altitude: Operating Storage0 to 5000 m 0 to 12192 m0 to 16,400 feet 0 to 40,000 feet Measured Power Consumption: Full Power Typical Settings Energy Star® Test Methods Sleep Switch Off40 watts 35 watts 33.1 watts 0.5 watts 0.5 watts Input Terminal One VGA connector with cable included; one DVI connector with cable included; one DisplayPort connector (cable not included) 24 Appendix A Technical Specifications ENWW