HP L1945wv User Guide

2.Swivel the monitor to the left or right for the best viewing angle (select models).
Figure 3-11  Swiveling the Monitor
3.Adjust the monitors height so that it is parallel to your eye height for a comfortable viewing position
(select models).
Figure 3-12  Adjusting the Height
Adjusting the Monitor 13
 

4.Pivot the monitor clockwise from landscape to portrait orientation viewing to adapt to your
application (select models).
Figure 3-13  Pivoting the Monitor
NOTE:To view information on the screen in portrait mode, you will need to install the Pivot Pro
software included on the software and documentation CD. The position of the OSD menu can also
be rotated to portrait mode. To rotate the OSD menu, access the OSD menu, select Management,
then select OSD Control.
Turning on the Monitor
1.Press the power...

Connecting USB Devices
Two USB connectors (on select models) are used to connect devices such as a digital camera, USB
keyboard, or USB mouse.
NOTE:You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0
ports on the monitor. Refer to Step 4 in 
Connecting the Cables on page 10.
Figure 3-14  Connecting USB Devices
Using the Accessory Rails
The monitor features accessory rails on the rear that can be used to mount optional devices, such as
the HP speaker bar, to attach to...

Removing the Monitor Pedestal Base
You can remove the monitor panel from the pedestal base to install the panel on a wall, a swing arm,
or other mounting fixture.
CAUTION:Before beginning to disassemble the monitor, be sure the monitor is turned off and the
power and signal cables are both disconnected. If the monitor has a connected audio cable, disconnect
it.
1.Disconnect and remove the signal and power cables from the back of the monitor.
2.Lay the monitor face down on a flat surface.
3.Remove the...

b.On the single-hinged base, there are three screws that connect the monitor panel to the
pedestal base.
Figure 3-17  Removing the Single-Hinged Pedestal Base
4.Lift up on the pedestal base to remove it from the monitor display head.
Mounting the Monitor
HP provides an HP Flat Panel Monitor Quick Release (purchased separately) that installs to the back
of the monitor panel and allows you to quickly and securely attach the panel to a wall or swing arm
mounting fixture. To install the HP Quick Release:...

3.Place the optional HP Quick Release onto the back of the monitor. Line up the holes on the HP
Quick Release with the mounting holes on the back of the monitor.
Figure 3-18  Mounting the HP Quick Release
4.Insert four 10mm screws into the mounting holes and tighten.
5.Mount the HP Quick Release to a swing arm or other mounting fixture using the four screws
removed from the back of the monitor in the previous step.
Figure 3-19  Installing the HP Quick Release
CAUTION:The HP Quick Release is designed to...

6.Insert the monitor panel into the HP Quick Release, and then press down firmly on the monitor to
lock it in place. When the HP Quick Release locks, it will make a clicking sound.
Figure 3-20  Inserting the Monitor Panel into the HP Quick Release
7.Reconnect the cables to the monitor panel.
Locating the Rating Labels
The rating labels on the monitor provide the spare part number, product number, and serial number.
You may need these numbers when contacting HP about the monitor model. The rating labels...

4 Operating the Monitor
Software and Utilities
The CD that comes with the monitor contains files you can install on the computer:
●an .INF (Information) file
●an .ICM (Image Color Matching) file
●auto-adjustment pattern utility
●additional software for the monitor model
NOTE:If the monitor does not include a CD, the .INF and .ICM files can be downloaded from the HP
monitors support Web site. See 
Downloading from the Worldwide Web on page 21 in this chapter.
The Information File
The .INF file defines...

Installing the .INF and .ICM Files
After you determine that you need to update, you can install the .INF and .ICM files from the CD or
download them.
Installing from the CD
To install the .INF and .ICM files on the computer from the CD:
1.Insert the CD in the computer CD-ROM drive. The CD menu is displayed.
2.View the Monitor Driver Software Readme file.
3.Select Install Monitor Driver Software.
4.Follow the on-screen instructions.
5.Ensure that the proper resolution and refresh rates appear in the...

To use the auto-adjustment feature:
1.Allow the monitor to warm up for 20 minutes before adjusting.
2.Press the -/Auto button on the monitor front panel.
●You can also press the Menu button, then select Image Control from the OSD Main Menu.
Refer to 
Adjusting the Monitor Settings on page 24 in this chapter.
●If the result is not satisfactory, continue with the procedure.
3.Insert the CD in the disc drive. The CD menu is displayed.
4.Select Open Auto-Adjustment Software. The setup test pattern is...