HP L1906 User Guide

2

Safety and Maintenance 
Guidelines 
Important Safety Information 
A power cord is included with your monitor. If another cord is 
used, use only a power source and connection appropriate for this 
monitor. For information on the correct power cord set to use with 
your monitor, refer to the “Power Cord Set Requirements” section 
in Appendix C. 
ÅWARNING: To reduce the risk of electric shock or damage to your 
equipment, do not disable the power cord grounding feature. This 
equipment is designed to...

Safety and Maintenance Guidelines 
ÄCAUTION: For the protection of your monitor, as well as your 
computer, connect all power cords for your computer and its 
peripheral devices (such as a monitor, printer, scanner) to some form 
of surge protection device such as a power strip or Uninterruptible 
Power Supply (UPS). Not all power strips provide surge protection; 
the power strips must be specifically labeled as having this ability. 
Use a power strip whose manufacturer offers a Damage Replacement...

Safety and Maintenance Guidelines 
■�Slots and openings in the cabinet are provided for ventilation. 
These openings must not be blocked or covered. Never push 
objects of any kind into cabinet slots or other openings. 
■�Do not drop your monitor or place it on an unstable surface. 
■�Do not allow anything to rest on the power cord. Do not walk 
on the cord. 
■�Keep your monitor in a well-ventilated area, away from 
excessive light, heat or moisture. 
■�When removing the monitor base, you must lay the...

Safety and Maintenance Guidelines 
2–4 User Guide 
 

3

Setting Up the Monitor 
To set up the monitor, ensure that the power is turned off to the 
monitor, computer system, and other attached devices, then 
follow the steps below. 
Installing the Monitor Pedestal 
To install the monitor pedestal: 
1. Place the pedestal plate on your desktop or table and check to 
be sure the arrow on the underside of the plate is facing 
forward. 
✎ Do not install the base if the monitor will be used on a wall, 
swing arm, or other mounting fixture; instead see the...

Setting Up the Monitor 
2. Using both hands, position the monitor over the pedestal base 
and press down firmly to lock the pedestal base in place. 
When the base locks, it will make a clicking sound. Make 
sure the pedestal base is securely locked before continuing 
with the setup. 
Inserting the Monitor into the Pedestal Base 
3–2 User Guide 
 

Setting Up the Monitor 
Connecting the Monitor 
1. Place the monitor in a convenient, well-ventilated location 
near your computer. 
2. Connect the monitor signal cable on the back of the monitor 
to the video connector on the rear panel of the computer. 
ÅWARNING: To reduce the risk of electric shock or damage to your 
equipment: 
■�Do not disable the power cord grounding plug. The grounding 
plug is an important safety feature. 
■�Plug the power cord into a grounded (earthed) electrical outlet 
that...

Setting Up the Monitor 
3. Connect one end of the power cable to the back of the 
monitor, and the other end to an electrical wall outlet. 
Connecting the Signal and Power Cables 
3–4 User Guide 
 

Setting Up the Monitor 
4. Adjust the monitor as needed for your comfort using the 
monitor’s tilt adjustment capability. 
Tilting the Monitor 
5. Press the power switch to turn on the monitor. 
ÄCAUTION: Burn-in image damage may occur on monitors that 
display the same static image on screen for a prolonged period of 
time. To avoid burn-in image damage on your monitor screen, you 
should always activate a screen saver application or turn off the 
monitor when it is not in use for a prolonged period of...

Setting Up the Monitor 
Removing the Monitor Base 
You can remove the monitor base to mount the monitor on a wall, 
a swing arm, or other mounting fixture. Read the Caution and 
Warning statements below before beginning the procedure. 
ÄCAUTION: Before beginning to disassemble the monitor, be sure 
the monitor is turned off and the power and signal cables are both 
disconnected. If your monitor has a connected audio cable, 
disconnect it. 
Ä
CAUTION: Do not remove the base from the monitor while the...