HP Ep7112 Digital Projector Users Guide
Have a look at the manual HP Ep7112 Digital Projector Users Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Adjusting the projector User’s Guide 41 Sound menu Setup menu Help menu Sound menu Mute Turns off the projector’s speaker. Volume Adjusts the loudness of the speakers. Internal speakers Sets whether the internal speakers are turned on. Reset sound settings Restores sound settings to their default settings. Setup menu Language Selects the language used by the on-screen menu. Projector position Adjusts the picture to match the orientation of the projector: upright or upside-down, in front of or behind the screen. Inverts or reverses the image accordingly. Timeout for menu Sets how many seconds the on-screen menu waits for input before it closes. DVI compatibility Sets the configuration of DVI port. If a computer connected to the DVI port always projects a low-resolution image, use VGA only. Reset lamp hours For a new lamp, resets the hours of use. Reset all settings Restores all menu settings to factory default settings. Help Displays information and status for the projector. Diagnostics... Show tests for checking the operation of the projector and the remote control.
User’s Guide 43 4 Maintaining the projector Getting the projector status To get the projector status, press the menu button on the projector or remote control and go to Help. This screen shows information and status for the projector. Cleaning the projector lens You can clean the front lens of the projector using the following recommendations. You cannot clean any of the internal surfaces. ■To minimize the risk of damaging or scratching the lens surface, blow dust particles off the lens with clean, dry, deionized air. ■If this method does not work, use the following method: a. Wipe the lens in a single direction with a clean, dry cloth. Do not wipe back and forth across the lens. b. If the cloth is dirty or smears the lens, wash the cloth. If the cloth is still dirty after washing it or the fabric is damaged, replace it. Ä Cleaning requires special consideration: ■Do not spray any type of fluid or cleaner directly on the lens surface. Cleaners might damage the lens. ■Do not use fabric softener when washing a cleaning cloth or softener sheets when drying the cloth. Chemicals on the cloth might damage the surface of the lens. ■Do not store a cleaning cloth in contact with the lens for a long time because doing so contaminates the lens with dye from the cloth. The cloth can be contaminated if left in the open air.
44 User’s Guide Maintaining the projector Replacing the lamp module As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage. You can install a new lamp at any time to bring the projector up to factory-fresh brightness. We recommend replacing the lamp if a warning message is displayed. Å Replacing the lamp module requires special consideration: ■To reduce the risk of injury, be careful when removing the lamp module as broken glass might be present. For a ceiling installation, wear goggles and gloves when removing the lamp module. If the lamp is broken, contact HP about repairs that might be required due to glass fragments. ■The lamp contains a small amount of mercury. If the lamp breaks, adequately ventilate the area where the breakage occurred. Disposal of this lamp might be regulated due to environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance at http://www.eiae.org. ■Because the lamp assembly operates at a very high temperature, wait 30 minutes before removing the lamp module. 1. Turn off the projector and allow it to cool for 30 minutes. 2. Unplug the power cord. 3. Loosen the 3 screws 1 on the front cover and pull out the front cover until the tab 2 at the right end comes out of the projector 3. 4. Loosen the two screws 4 on the lamp module, and pull out the module 5.
Maintaining the projector User’s Guide 45 5. Insert the new lamp module into the projector and tighten the two screws. 6. Insert the tab on the front cover into the slot in the projector and close the cover. 7. Tighten the screws that hold the cover. 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp. 9. Press menu, go to Setup > Reset lamp hours, and press ok. Replacing the battery in the remote control 1. On the back of the remote control, push in the tab 1 and remove the battery cover 2 to reveal the batteries. 2. Remove the old batteries and install two new AAA batteries 3. 3. Install the battery cover. When discarding old batteries, contact your local waste-disposal provider regarding local restrictions on the disposal or recycling of batteries.
User’s Guide 47 5 Installing permanently Installing the projector Installing on a table This installation is covered in detail in Chapter 1. See “Setting up the projector” on page 15 for more information. Installing on the ceiling Å WARNING: To minimize the risk of injury from improperly installed equipment, it is recommended that a professional installer performs the ceiling installation. 1. Attach the projector to the ceiling using an HP L1733A ceiling mount kit. The base of the projector must by removed when it is attached to the ceiling mount. See the installation instructions provided with the ceiling mount kit. 2. After the projector is mounted on the ceiling, adjust the projector settings to match this setup. Press menu, select Setup > Projector position, and select Front Ceiling from the drop-down list. Installing for rear projection 1. Place the projector 1 to 10 m (3 to 33 ft) behind a translucent screen that is designed for rear projection. See “Setting up the projector” on page 15 or “Installing on the ceiling” on page 47 for more instructions. 2. Press menu and select Setup > Projector position. Then select Rear Table or Rear Ceiling.
48 User’s Guide Installing permanently Connecting to a room controller If your projector has a serial port, you can connect the projector to a room controller using a serial (RS-232) cable. After you program the room controller using the following commands, you can use the room controller to operate the projector and other components of your home theater. Serial connections The serial port on the projector uses a standard serial (RS-232) cable: ■Pin 2: data sent to the projector (RxD) ■Pin 3: data sent from the projector (TxD) ■Pin 5: ground The room controller must use the following serial (RS-232) settings: ■9600 baud ■1 start bit + 8 data bits (D0=LSB, D7=MSB) + 1 stop bit ■No parity ■Full duplex communication channels (no flow control) ■No handshaking Examples of room controller commands In the following examples, “” and “” represent a carriage return and line feed, respectively. Commands are sent to the projector as requests which consist of an asterisk (*) prefix, the command name, any needed parameter, and a carriage return as a terminator: * command = parameter Requests can contain only ASCII alphanumeric characters. Blanks (spaces) are allowed, except within keywords and numbers. Line feeds are ignored.
Installing permanently User’s Guide 49 The following table shows the specific syntax to use for various requested tasks. In general, every request sent to the projector generates one or more notification messages, which are sent to the room controller. Actions initiated by the projector can also generate notifications. The projector always sends notifications whenever a setting changes, whether as the result of a request from a controller, or as the result of an action, such as a button press or menu change. Some requested setting changes take time to perform, or are carried out in stages. Because of this, requests might produce delayed notifications. The following table lists the types of notifications generated in various situations. Incorrect commands cause the following types of notifications: ■No asterisk at start of command—no response ■Unrecognized command name—command with “?” added ■Command that is currently unavailable—command with “?” added To perform this task... Use this request syntax... Change a setting to a specified value *command=value Ask the current setting*command=? Increment a setting*command=+ Decrement a setting*command=- Invoke an action (no parameter needed)*command This type of request... Generates this type of notification... Modify a setting Echoes the request command and shows the resulting value: Request: *BRT=65 Notification: *BRT=65 Query a setting Echoes the request command and shows the resulting value: Request: *CON=? Notification: *CON=40 Execute an action Echoes the request command: Request: *NXT Notification: *NXT
50 User’s Guide Installing permanently ■Invalid parameter—command with current value ■Action command with unnecessary parameter—action command ■Action command that is unavailable—action command The following simplified example shows how the projector typically responds to a request to change the active input source. Note that the three latter notifications are delayed. Room controller commands In the following tables, if the parameter listing for a particular command is “None,” that command requires no parameter. Some commands are valid only when the projector is turned on, STAT=1. Some commands are available only when specific input sources are active. Request:*RSRC=4 Notification:*RSRC=4(acknowledges request) *SRC=0(projector is attempting to acquire source 4, and in the interim has no valid source) *SRC=4(source 4 is now active) *BRT=60(brightness has been modified for source 4) *CSPC=?(color space is not supported for this input) Source functions Command Parameters Description SRC? Queries the current active input source: 0=no active source, 3=composite video, 4=S-video, 5=component video, 8=DVI. RSRC3,4,5,8,? Attempts to use the specified source as the active input source, or queries the last source requested: 3=composite video, 4=S-video, 5=component video, 8=DVI. NXTNone Switches to the next input source.