HP DesignJet 9000s User Manual

a.Select ROLL using the ▲ or ▼ keys. For the NEST option, see How do I...Use manual nesting.
b.Press the OK key to confirm the selection.
17.Select a media type.
a.Select the media type with the ▲ or ▼ key.
There are five preset media types to choose from:
●Paper
●Glossy
●Matte
●Banner
●BLT_B (Backlit)
b.Press the OK key to confirm.
NOTEIf you wish to select a media type that is currently not available, then you
will need to create a new media type.
c.Select the NEW MEDIA ENTRY option using the ▲ or ▼...

Remove a media roll from the printer
To remove a media roll from the printer:
1.Lift the media load lever.
2.Loosen the left media hub lock, and pull the left media hub out of the media roll.
1. Left media hub
2. Lock
3. Media roll
32 Chapter 3   How do I load/unload media? ENWW
How do I load/unload media?
 

3.Remove the media roll from the printer.
CAUTIONHandle media rolls with care. They can be heavy and difficult to move in
confined spaces. In some cases, two people should move and install media rolls.
Dropping a media roll could cause personal injury or damage to the printer.
1. Media roll
2. Right media hub
Replace a jammed media roll
To replace a jammed media roll, see The problem is... A head crash.
ENWW Replace a jammed media roll 33
How do I load/unload media?
 

Load cut sheet
The printers front panel messages will guide you through the process of loading media. To load cut
sheet:
1.Open the rear cover and slide the media edge guards to each end of the platen.
Slide the fan guide lever to the right side of the platen to avoid obstructing the media path and
damaging the media.
NOTEPosition the media edge guards after loading the media. See How do I.. Use themedia edge guard.
Position the fan guide lever after loading the media.
2.Close the rear cover.
34 Chapter...

3.Lift the media load lever.
4.When installing the cut sheet in the printer, align the cut sheet to the left of the guide line.
1. Guide line
ENWWLoad cut sheet 35
How do I load/unload media?
 

5.Ensure the ME (Media End) lever is in the forward position.
6.Feed the media until a beep sounds from the media feeder (about 200 mm).
NOTEIf you have problems loading media, feed the media into the printer by holding
both edges of the media.
Take care that the media does not curl inside the rear cover and that the media edge
guards are not obstructing the media path. See How do I... 
Use the media edge guard.
36 Chapter 3   How do I load/unload media? ENWW
How do I load/unload media?
 

7.Lower the media load lever.
8.Open the rear cover and adjust the media edge guards and adjust the position of the fan guard
lever.
1. Fan guard lever
2. Media edge guard
To complete the loading procedure, follow the front panel instructions.
9.Confirm the position of the media edge guard and press the OK key.
10.Select cut sheet.
ENWWLoad cut sheet 37
How do I load/unload media?
 

a.Select SHEET using the ▲ or ▼ keys. For the NEST option, see How do I... Use manualnesting.
b.Press the OK key to confirm.
11.Select a media type.
a.Select the media type with the ▲ or ▼ key.
There are five preset media types to choose from:
●Paper
●Glossy
●Matte
●Banner
●BLT_B (Backlit)
b.Press the OK key to confirm.
NOTEIf you wish to select a media type that is currently not available, then you
will need to create a new media type.
c.Select the NEW MEDIA ENTRY option using the ▲ or ▼ key and press...

Use the take-up reel
There are three tasks required to complete loading of media on the take-up reel. The first part of
attaching a roll to the take-up reel is attaching the end of the roll (with tape) to the core tube supplied
with the take-up reel. You can also use an empty cardboard tube. Both types of core must be the same
length as the roll you are using.
●Set the take-up reel for clockwise or anti-clockwise winding.
●Define the winding mode.
●Load media onto the take-up reel.
Set the take-up reel...

1. Take-up reel off
2. Internal (anti-clockwise) winding
3. External (clockwise) winding
NOTEFor LOOSE winding mode, make sure that the media passes inside the take-up reel
sensor.
If the take-up reel is not used, turn the take-up reel switch off.
Make sure that you change the media roll on the take-up reel before the roll size exceeds the
diameter of the take-up reel media stop. Replace the core tube with a new one to avoid
winding errors.
1. Take-up reel sensor
40 Chapter 3   How do I load/unload...