HP DesignJet 510ps 610 mm User Manual

ANSI paper
The following table lists the printable area for the ANSI paper
 size system. The left and right margins are 0.2 in 
(5 mm) and the leading and trailing edge margins are 0.7 in (17 mm).
Where
: 
Printable areas for ANSI paper
Paper size
Orientation of  paper in printer
Printable area (width × height) by image orientation
Inches
Millimeters
Landscape
Portrait
Landscape
Portrait
Width
Height
Width
Height
Width
Height
Width
Height
A Portrait 9.7 8.1 8.1 9.7 245 206 206 245
Landscape 7.2 10.6 10.6...

Architectural paper
The following table lists the printable area for the Architectural paper
 size system.
The left and right margins are 0.2 in (5 mm) and the leading and trailing edge margins are 0.7 in (17 mm).
Where:
 . 
Printable areas for Architectural paper
Paper size
Orientation of  paper in printer
Printable area (width × height) by image orientation
Inches
Millimeters
Landscape
Portrait
Landscape
Portrait
Width
Height
Width
Height
Width
Height
Width
Height
C Portrait 22.7 17.6 17.6 22.7 576 447...

ISO paper
The following table lists the printable area for the ISO paper
 size system.
The left and right margins are 0.2 in (5 mm) and the leading and trailing edge margins are 0.7 in (17 mm).
Where:
 
Printable areas for ISO paper
Paper size
Orientation of  paper in printer
Printable area (width × height) by image orientation
Inches
Millimeters
Landscape
Portrait
Landscape
Portrait
Width
Height
Width
Height
Width
Height
Width
Height
A4 Portrait 10.4 7.9 7.9 10.4 263 200 200 263 Landscape 6.9 11.3 11.3...

Roll paperThe following procedures are described in detail, with animations where appropriate:• Installing a new roll on the printer
•Loading roll paper•Unloading roll paper•Removing roll paper from the spindle•Cutter replacement
 

Installing a new roll on the printerThe graphical sequence
 shows how to install a new roll of paper on the printer.
CAUTION:
Make sure the printer wheels are locked (the brake lever on each wheel is pressed Down) to 
prevent the printer from moving.
If you are a regular user of different types of roll paper, you can change the paper quicker if you have more than 
one spindle. This allows you to do the following:
1. Pre-load the different types of paper onto the spindles.
2. Remove and replace the...

Loading roll paperThe graphical sequence
 shows how to load a new roll of paper on the printer.
NOTE: You must have installed
 a new roll of paper on the printer before you can load it.
The front-panel menu items are:
Select (using the   keys)  Then press:
1. Paper Enter
2. Load Roll Enter
3. Select Roll Type Enter
 

Unloading roll paperThe graphical sequence
 shows how to unload a roll of paper from the printer.
 

Removing roll paper from the printerThe graphical sequence
 shows how to remove a roll of paper from the printer. 
NOTE: You must have unloaded
 the roll of paper from the printer before you can remove it.
 

Removing roll paper from the spindleThe graphical sequence
 shows how to remove a roll of paper from the roll  spindle
. 
NOTE: You must have removed
 the roll of paper from the printer before you can remove it from the 
spindle.
 

Cutter replacementThe graphical sequence
 shows the complete procedure for the replacement of the paper cutter in your printer.
PrerequisitesBefore attempting to replace the cutter you must contact your local  HP Customer Care
 center to:
• Order the replacement cutter.
• Receive instructions on how to access the front panel Service menu.
Important information• The cutter unit is attached to the printer by a black cutter holder that runs along the metal guide rail, and is  hooked onto the edge of the...