HP DesignJet 510 610 mm User Manual

Paper advance calibration is 
recommended.
Press ENTER to calibrate
You are recommended to perform the Advance calibration routine, 
to ensure the optimum print quality.
Press the Enter key to create the calibration pattern. See  Advance calibration
.
Paper advance calibration is 
recommended. Load paper 
and select Paper advance 
calibration.
Press ENTER to finish You are recommended to perform the Advance calibration routine, 
to ensure optimum print quality.
Load a sheet or roll of paper and then...

Paper not present.
Load paper to print calibration 
patternThe paper axis calibration routine has been triggered without having 
paper loaded.
Load paper; see 
Advance calibration
 for details of the routine.
Paper too big to scan the 
pattern after printing it
During paper loading for the Calibration routine, the printer has 
detected that it will not be able to load the paper when it will be 
needed for scanning. The minimum size required for the print is 
65 cm (25 in) long and 50 cm (20 in) wide....

Paper too small to print the 
pattern
The paper loaded is not big enough to contain the paper axis 
calibration pattern.
Load a roll or sheet that is at least 65 cm (25 in) long and 50 cm 
(20 in) wide.
Paper too small
Press ENTER to retry
Press CANCEL to abort While loading paper into the printer 
(roll or sheet), the printer has 
found that it is either too narrow or too short (sheet only) to be 
loaded properly.
Press the  Enter key to load larger paper, or the  Cancel key to stop 
the load process....

Possibly a paper jam1. Open window
2. Switch power off
3. Clear paper path
4. Switch power on
5. Align printheads
There may be paper jammed in the printer. (The printer has 
detected that a motor is blocked and the likely cause is a paper jam; 
however, it may be due to some other cause.)
Follow these steps to check the paper path, as described in  Clearing a paper jam
. When the jammed paper has been cleared, you are 
strongly recommended to align the printheads, as they are quite 
likely to have become...

Printheads not aligned
Paper type not valid
to align printheads
Press ENTER to continueYou have replaced one or more printheads but the printer has 
detected that you do not have the right type of paper loaded for the 
alignment process.
Press the 
Enter key to load the correct type of paper, or the  Cancel 
key to stop the load process.Printheads not aligned
Paper too small
to align printheads
Press ENTER to continue
You have replaced one or more printheads but the printer has 
detected that you do not...

Problem found during 
calibration
A general problem was found during the Advance calibration
 
routine.
Respond to any other messages that appear on the front panel, 
indicating ink or paper pr oblems, and then retry the  Advance 
calibration  routine.
Problems detected in INK 
CARTRIDGES.
Continue process and replace 
them.
Press ENTER to continue There is an error with the ink cartridges during the preparation of the 
ink system.
Press the 
Enter key and then follow the instructions to replace the...

Right edge of sheet too far 
from load line
Press ENTER to retry
Press CANCEL to abortDuring the loading of a sheet of paper, the printer has detected that 
the paper is too far to the left; it should be aligned close to the blue 
line painted on the right side of the platen.
Either
: Press the Enter  key to restart the loading procedure;
Or : Press the  Cancel key to cancel paper loading.Roll edge not found
Please check roll edges are 
non-clear
Press ENTER to retry
Press CANCEL to abort
During the...

Sheet too long
Please check it is not a roll
Press ENTER to retry
Press CANCEL to abort
You have requested the printer to load a sheet of paper, but the 
sheet appears to be too long.
Check that the paper is not a roll.
Either: Press the Enter  key to try to load the sheet again;
Or : Press the  Cancel key to stop the process. If the paper is on a 
roll, follow the instructions in Loading roll paper
.
Troubleshooting finished
Resume normal printing
If problem persists select 
Troubleshooting again
Press...

Unknown ink cartridges.
Press ENTER to continue.The ink cartridges are not recognized by the printer as HP-
approved, and there is at least one that is new.
Press the 
Enter key.Unknown paper format
Reload paper
The format (roll or sheet) of the paper loaded in the printer is 
unknown.
Reload the paper following the normal procedure, to solve this 
problem. See  Loading roll paper
 or Loading sheet paper
.
Unknown paper type
Select paper type The type of the paper loaded in the printer is unknown to the...

Front-panel messages (continued)
Message
Explanation and Action
Warning!
Machine calibrations need to 
be performed. Refer to guide 
for instructions.The color calibrations for the paper that is loaded have been lost.
Follow the procedure described in 
Advance calibration
.
Warning: color calibration not 
done on this paper type
The printer has detected that this paper type has not been color-
calibrated, and the system is configured to do it.
To calibrate color for the current paper type, select  Ink...