HP DesignJet 510 1067 mm User Manual

							Set-up menu
HelpPrint qualityPrinter InformationModel number, Serial number, Service ID, 
Firmware rev, Accessory rev, Paper used, 
Ink used (c, m, y, k), Scan axis usage,  Paper axis usage, Service station usage,
Spittoon usage, Pinch-lift usage, Cutter 
usage, Ink usage.
NormalFastViewPrintBest
Advanced Options
Best Quality SettingsOptimize for
ImagesLine drawings / textMaximum detailDefault
Define Palette
Pen no. 0  …  15Pen no. 0  …  15
0.13 … 12.0mm0 … 256
WidthColor
Palette
HPGL/2 settings
Merge
Palette A, Palette BFactorySoftware, Factory, Palette A, BOn/Off
Fast Quality Settings
Increased speedDefault
More menu options
 
 
						

							Set-up menu (continued)
Items always shown
BuzzerContrast
Front Panel
Altitude
Language
English, German, Spanish, French, Italian,
Japenese, Portuguese,  Korean, Chinese,
Taiwanese, …
Log
PrintheadsErrorsService testsService calibrationsService utilities 0-1000m
1000m - 2000m
>2000mON/OFF0%, 5%, … , 100%
Service tools
Hidden items that can only be accessed
from the Set-up menu through a 
certain combination of keys
Card setupI/O Timeout
No I/O Cards present
Reset Card 
No I/O Cards present / Contents provided by cardConfigurationAdvanced30 sec, … , 30 min
I/O setup
Card ID
Previous menu options
 
 
						

							Navigating the menu systemFrom the top level of the menu system, you can navigate through the menus using the display keys. Any menu 
item followed by a greater-than symbol (>), indicates that a further level of menu items is available.
See Navigation example
 for a brief overview of the menu system.
Press the  Up  and  Down   keys to scroll 
up and down though the menus or menu 
options.
Press  Menu to return to the top level 
without changing any menu selections. 
This will bring you to the four menu icons.
Press 
Back to return to the previous menu 
level without changing any menu selections.
Press Enter to:
• Select a menu and move to the next menu level.
• Change the value of the selected menu item.
 
						

							Navigation exampleThis section provides a typical example of how to navigate through the menus to configure a specific print option.
How to set the ink-drying time to two minutes
The front panel menu structure diagram for the Ink menu
 shows that the path to the Drying time option is:
Ink menu   → Drying time
Use the following procedure to set the ink-drying time to two minutes.
Setting drying time navigation example
Key action
Display
Result
1. Use the Up   and 
Down    keys to high-
light the  Ink menu icon. The 
Ink menu icon is 
highlighted to allow you to 
select the Ink  menu options.
2. Press the  Enter key to 
enter the printer  Ink 
menu. The display shows the 
Ink 
menu to allow you to select 
drying time.
Continued …
 
						

							3. Use the Up  and 
Down    keys to 
highlight the  Drying 
time  menu option. The display shows the 
Drying 
time  option highlighted.
4. Press the  Enter key to 
enter the Drying time  
menu. The display shows the 
Drying 
time  menu to allow you to 
select the type of drying time 
you require.
5. Use the Up   and 
Down    keys to 
highlight the  Manual 
menu option. The display shows the 
Manual
 option highlighted. 
6. Press the  Enter key to 
enter the Manual  drying 
time setting menu. The display shows the 
Manual
 drying time setting 
menu to allow you to select 
the drying time you require.
Previous …
Continued …
Setting drying time navigation example
Key action
Display
Result
 
						

							7. Press the Up  key 
once to select two 
minutes. The display shows the 
Manual
 drying time setting 
menu with two minutes 
selected.
8. Press the  Enter key to 
set the drying time to two 
minutes. If the front-panel buzzer is set 
ON, there will be a short 
‘beep’ to confirm the change. 
A tick mark (
√) in the right side 
of the field confirms the value. 
9. Press the Top key to  return to the top level 
menu. The display shows the 
Ink 
menu.
Previous …
Setting drying time navigation example
Key action
Display
Result
 
						

							Message descriptionsThis is a list of the error messages in the front-panel display. If an action is needed, it is shown in italics in the 
Explanation and action  column. The messages are listed in alphabetical order. Other front-panel messages, 
such as prompts, are included in the descriptions of the relevant procedures elsewhere in this document.
Front-panel messages
Message
Explanation and action
Alignment error due to 
printheads.
Press ENTER to see faulty 
printheads The printer was aligning its printheads, but encountered an error 
due to some printheads not printing properly. Alignment has 
stopped.
Press the 
Enter key.Alignment error
Press ENTER to continue
The printer was aligning its printheads, but encountered an error. 
Alignment has stopped.
Press the  Enter key.
Cartridges will expire in days: 
nn One or more of the cartridges are about to expire. nn is the number 
of days until expiry date of the cart
ridge that will expire first. The 
cartridges that are about to expire are indicated below this message.
For an explanation of the replacement procedure, see  Ink cartridge replacement
.
Color calibration error
Press ENTER to continue
The printer was performing a calibration of its color system, but 
encountered an error.
Press the Enter key.
 
						

							Error
Select Replace PrintheadsThe printer has detected that one or more of the printheads is 
missing or has an error, as indicated by flashing crosses. The four 
icons refer from left to right to the Cyan (
•), Black ( •), Magenta ( •) 
and Yellow ( •) printheads.
For an explanation of the replacement procedure, see  Printhead 
replacement
.
HP is not responsible for 
damage from use of non-HP
ink.
Replace
Continue
The printer has determined that one or more of the ink cartridges is 
not an HP product. Your product warranty applies only when you 
use HP ink. Any damage caused to your printer resulting from the 
use of non-HP ink cartridges is not the responsibility of Hewlett-
Packard.
If you want to replace the non-HP ink cartridges, select  Replace and 
press the  Enter key. Otherwise, select Continue  and press Enter to 
continue.
HP is not responsible for 
damage from use of non-HP
printheads. Replace
Continue The printer has determined that one or more of the printheads is not 
an HP product. Your product warranty applies only when you use 
HP printheads. Any damage caused to your printer resulting from 
the use of non-HP printheads is not the responsibility of Hewlett-
Packard.
If you want to replace the non-HP printheads, select 
Replace and 
press the  Enter key. Otherwise, select Continue  and press Enter to 
continue.
Front-panel messages
Message
Explanation and action
 
						

							Ink cartridge replacement 
required
The printer has detected that one or more of the ink cartridges is 
missing or has an error, as indicated by flashing crosses. The four 
icons refer from left to right to the Cyan (•), Black ( •), Magenta ( •) 
and Yellow ( •) cartridges.
For an explanation of the icons and details of the replacement 
procedure, see  Ink cartridges
.
INK CARTRIDGES need to be 
functional.
Replace before replacing 
printheads You have attempted to replace printheads, but the printer has 
detected that there are ink cart
ridges that are wrong. The ink 
cartridges must be replaced before the printheads can be replaced.
First replace the faulty, empty or missing ink cartridges and then 
replace the printheads. See  Ink cartridge replacement
 and 
Printhead replacement
.
Install missing cartridges and 
replace empty cartridges 
before replacing printheads
You are replacing printheads, but the printer has detected that some 
cartridges are empty and some are missing. The empty cartridges 
must be replaced and the missing ones inserted before the 
printheads are replaced.
Follow the procedure for  Ink cartridge replacement
. Press the Enter or 
Cancel  key to continue.
Install missing cartridges 
before replacing printheads You are replacing printheads, but the printer has detected that one 
or more cartridges are missing. 
The missing cartridges must be 
installed before the printheads are replaced.
Follow the procedure for  Printhead replacement
. Press the Enter  or 
Cancel  key to continue.
Front-panel messages
Message
Explanation and action
 
						

							Open window and check 
printhead cover is properly 
closed
You have replaced one or more printheads and the printer’s check 
has found that the printhead cover is not securely closed.
Open the window and check the printhead cover. The procedure is 
described in the Printhead replacement
 procedure.
Note : This message may also appear following a paper jam, as the 
printer cannot detect the exact reason for the problem. In this case 
you may have to resort to powering off the printer or even removing 
the power cable from the machine, in order to recover from the 
problem. See  Clearing a paper jam
.
Open window and check 
proper installation of setup 
printheads During system start-up, which occurs when you first install the 
printer, you need to install the setup printheads. These special 
printheads cannot be used for printing, but must be used when the 
printer has been powered off. The printer has detected that the 
setup printheads have not been installed correctly.
Open the window and follow subsequent instructions to reinstall or 
relocate the setup printheads. Contact HP for advice if the setup 
printheads are missing or cannot be installed correctly.
Option not available now
You have selected an option in the menu that is not available at the 
moment. (The printer may be busy, out of ink, out of paper, etc.)
Out of paper The printer ran out of paper while printing the calibration pattern. Load a sheet or roll that is at least  65 cm (25 in) long and 50 cm 
(20 in)  wide.
Front-panel messages
Message
Explanation and action