HP DesignJet 4500ps User Manual

4.Highlight Load roll 1 and press the Select key.
5.Highlight the paper type you intend to load and press the Select key.
6.Using two hands, pull out drawer 1.
7.Remove the spindle from drawer 1.
ENWWLoad roll 1 77
How do I... (printer
assembly topics) [4500]
 

8.Use the supplied core adaptors when the roll core is of a larger diameter.
9.Remove the blue-colored stop from the left end of the spindle. Keep the spindle horizontal.
10.Slide the roll of paper that came with your printer onto the spindle. Make sure the paper is
oriented exactly as shown.
11.Push the black right-hand stop onto the roll. Make sure it is correctly seated.
78 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]
 

12.Put the blue-colored stop onto the spindle.
13.Push the blue left-hand stop onto the roll. Make sure it is correctly seated.
14.Hold the spindle assembly using the blue and black stops.
15.With the blue stop on the left, lower the spindle into drawer 1.
ENWWLoad roll 1 79
How do I... (printer
assembly topics) [4500]
 

16.Lift the drawer 1 paper load lever. This is located on the right-hand side of the printer, above
drawer 1.
17.Feed the paper from roll 1 onto the drawer 1 platen. Align the paper with the central blue line on
the right side of the platen.
18.Stop feeding the paper when the printer beeps.
19.Lower the drawer 1 paper load lever.
80 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]
 

20.Push in drawer 1.
21.Using the stops at each end of the spindle, carefully wind the excess paper back onto the
spindle.
22.Select the roll length if known.
Load roll 2
1.
To load roll paper from drawer 2: from the front panel, highlight the  icon and press the Select
key.
ENWWLoad roll 2 81
How do I... (printer
assembly topics) [4500]
 

2.Highlight Paper load and press the Select key.
3.Highlight Load roll 2 and press the Select key.
4.Highlight the paper type you intend to load and press the Select key.
5.Using two hands, pull out drawer 2.
6.Remove the spindle from drawer 2.
7.Load the spindle using the same procedure as already described for roll 1.
82 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]
 

8.With the blue stop on the left, lower the spindle into drawer 2.
9.Lift the drawer 2 paper load lever. This is located on the right-hand side of the printer and under
drawer 1.
10.Feed the paper from roll 2 onto the drawer 2 platen.. Align the paper with the central blue line
on the right side of the platen.
11.Stop feeding the paper when the printer beeps.
ENWWLoad roll 2 83
How do I... (printer
assembly topics) [4500]
 

12.Lower the drawer 2 paper load lever.
13.Using two hands, push in drawer 2.
14.Using the stops at each end of the spindle, carefully wind the excess paper back onto the
spindle.
84 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]
 

Assemble the bin
1.Locate all the parts for the bin assembly. The screwdriver is the same one used to fix the roll
module to the printer stand.
2.Lay one end frame on the floor. Hold one cross frame vertically with the angled part located at
the top of the end frame. The cross frame must be fixed onto the inside of the shortest leg of the
end frame.
3.Fix the cross frame to the end frame using two screws.
ENWWAssemble the bin 85
How do I... (printer
assembly topics) [4500]
 

4.Turn the bin assembly into a horizontal position. Attach the short leg of the second end frame to
the cross frame using two screws.
5.Attach the second cross frame to the bin assembly using four screws.
NOTEThis cross frame is mounted on the outside of the end frames.
6.Attach one end of the loop to the cross frame.
86 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]