HP DesignJet 4500 User Manual

14.Fix the left foot using four screws.
15.Position a foot on the right leg. There are pins to help you to position the foot correctly.
NOTEDo not remove the anti-slip material from the wheel.
16.Fix the right foot using four screws.
Attach the stand
1.You now need to identify the left and right of the printer. This information is shown on the foam
end packs. Also identify the rear of the printer.
ENWWAttach the stand 17
How do I... (printer
assembly topics) [4000]
 

2.Pull open the protective plastic from the base of the printer. Please ensure that there is a three-
meter space clear of obstructions to the rear of the printer.
Remove the two desiccant bags from the printer.
3.In this step, make sure you position the stand pins in the holes in the center of the printer body
brackets.
Lift the stand assembly onto the printer body. The anti-slip material should face to the rear of
the printer.
4.Fix the right side of the stand to the printer using one screw. Make sure...

5.Fix the left side of the stand to the printer using two screws. Make sure that the screws are fully
tightened.
6.Place the spare and consumables boxes against the rear of the printer box. The arrows on the
boxes must point towards the printer box.
Check that the anti-slip material is still fixed to the two rear wheels.
7.Using four people, rotate the printer on to the spare and consumables boxes.
Rotate the printer until its rear rests on the spare and consumables boxes and the wheels with
the...

8.Remove the pallet before trying to lift the printer into an upright position.
9.Using four people and the hand holds on the rear of the printer body, carefully lift the printer into
an upright position. The anti-slip material should stop the printer from sliding forwards.
Remove packaging materials
1.Remove the two foam end packs and the plastic covering the printer.
2.Position the left leg cover on the front of the left leg (1), then clip the rear edge (2) into place.
20 Chapter 2   How do I......

3.Position the right leg cover on the front of the right leg (1), then clip the rear edge (2) into place.
4.Remove the anti-slip material from the two rear wheels on the stand assembly.
5.Remove the packing tapes 1 to 8. Open the printer window and remove the two window inserts
9 and 10.
6.Remove the protective covering from the printer window and the front panel screen.
7.Remove the spindle lock.
ENWW Remove packaging materials 21
How do I... (printer
assembly topics) [4000]
 

8.Open the printhead cleaner door and remove the carriage packing material. Then close the
cleaner door.
9.Press the spindle lever down, which will unseat the right–hand end of the spindle. Remove that
end of the spindle first, and then the left. Do not insert your fingers into the spindle supports
during the removal process.
10.Remove the spindle lock foam piece. Then replace the spindle.
11.Install the Quick Reference Guide holder. Angle the holder at the top (1), then position the two
hooks and clip...

Assemble the bin
1.Locate the bin components.
2.Fix one screw to the inside of the stand’s left leg.
3.Do not fully fit the screw.
4.Fix one screw to the inside of the stand’s right leg.
5.Do not fully fit the screw.
ENWWAssemble the bin 23
How do I... (printer
assembly topics) [4000]
 

6.Lift the supporting framework of the bin into position in front of the printer.
7.Fix the top arms of the bin to the two screws that you have just fitted.
8.Fix the lower arms of the bin to the stand using one screw for each leg.
9.Now tighten the two top screws.
10.Clip all six loops to the frame of the bin. Locate the loops with rear extensions in positions 2, 4,
and 6.
24 Chapter 2   How do I... (printer assembly topics) [4000] ENWW
How do I... (printer
assembly topics) [4000]
 

11.Secure all six loops to the frame, using two clips on each loop.
12.Fit all three mobile stoppers to the three loops as indicated.
13.Carefully squeeze the mobile stopper and then fit it onto the loop.
14.When the mobile stopper is engaged with the loop, release your grip.
15.Move the three mobile stoppers into their parked position. These stoppers are used only when
printing on sheets of paper less than 900 mm in length (up to A1 size).
ENWWAssemble the bin 25
How do I... (printer
assembly topics)...

Switch on for the first time
1.Plug the power cable into the rear of the printer, then plug the other end into the AC power outlet.
2.Turn the power switch at the rear of the printer to the on position.
3.If the power light on the front panel remains off, press the Power key to switch on the printer.
4.Wait until you see this front panel message. Highlight your language on the front panel using
the Up and Down keys. Press the Select key.
5.The front panel will now display how to install the ink...