HP Compaq S2021 User Guide

Maintenance Guidelines  
To enhance the performance and extend the life of the monitor: Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those 
controls that are covered in the operating instructions. If the monitor is not operating properly or has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider. ● Use only a power source and connection appropriate for this monitor, as indicated on the label/ back plate of the monitor. ● Be...

3 Setting Up the Monitor Unpacking the Monitor 1. Unpack the monitor. Make sure all contents are included. Store the packing box. 2. Turn off the computer and other attached devices. 3. Determine whether the monitor will be desktop mounted or wall-mounted. See “Installing the Monitor” in this chapter. 4. Prepare a flat area to assemble the monitor. You may need a flat, soft, protected area for placing the monitor screen-down while preparing it for installation. 5. You need a Phillips screwdriver for...

2.     Align the column with the monitor support column and push forward until the column 
locks in place. Then align the stand with the column and push the stand towards the 
bottom of the monitor. Figure 3-1  Installing the monitor column and stand 3. Lift the monitor to an upright position and place on a flat, stable surface.  Figure 3-2  Monitor in upright position  Preparing the monitor for wall-mounting 1. Check the stability of the wall-mounting fixture. WARNING! To reduce the risk of personal...

Figure 3-3  Bottom view of monitor stand showing release button (circled) Figure 3-4  Remove the stand from monitor  8 Chapter 3   Setting Up the Monitor ENWW                                                                                                                                                                                                                                                      
4.   Press the release button as indicated first before removing the stand then follow the arrow...

6.   Follow the instructions included with the mounting fixture to ensure that the monitor is safely 
attached. 
         
The four threaded holes that are on the back of the panel are compliant with the VESA standard for mounting flat-panel monitors. ENWW Installing The Monitor 9                                           5.   Use the threaded holes to attach the wall mount bracket.  
 
Use the four holes (A), (B), (C), and (D) to attach the swing arm or other mounting fixture to the back of the monitor...

NOTE: If your computer has a DVI connector and no VGA connector, use a DVI-I to VGA adapter to connect your computer to the monitor. Connect the DVI-I to VGA adapter to the DVI connector on the computer graphic card, and connect the VGA cable to the adapter and the monitor.   Connect one end of the VGA video cable to the back of the monitor and the other end to the VGA video connector on the computer.                                Connecting Cables  
Connecting the VGA (Analog) Cable or DVI-D (Digital)...

Connecting the Audio Cable (select models) 
Connect the built-in monitor speakers to the computer by using the audio cable, as the 
following illustration shows Figure 3-7  Connecting the audio cables (select models) NOTE:   When using a VGA or DVI signal, you must connect your audio separately because a 
VGA or DVI signal converts only video data, not audio data.      ENWW Connecting Cables 11  
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
  

Connecting the Power Cable 1. Follow all Electrical and Power Warnings WARNING! To reduce the risk of electric shock or damage to your equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet. 
Be sure that the grounded power outlet you plug the power cord into is easily accessible to the 
operator and located as close to the equipment as possible. A power cord should be routed so that it is...

Adjusting the Tilt   
For optimal viewing, adjust the screen tilt to your own preference, as follows: 1. Face the front of the monitor and hold the base so that you do not topple the monitor while changing the tilt. 2. Adjust the tilt by moving the top edge of the monitor either toward or away from you, without touching the screen. Figure 3-9 Tilt adjustment ENWW Adjusting the Tilt 13  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
  

4 Operating the Monitor CD Software and Utilities  
The CD that is included with this monitor contains drivers and software that you can install on your computer. Installing Drivers  
If you determine that you need to update the drivers, you can install the monitor driver INF and ICM files from the CD, or download them from the Internet. Installing the monitor driver software from the CD 
 
To install the monitor driver software from the CD: 1. Insert the CD in your computer CD drive. The CD menu...