HP Compaq Q1859 User Guide

User’s Guide3-1
3
Setting Up the Monitor
Unpacking the Monitor
1.Unpack the monitor. Make sure all contents are included. Store the packing box.
2.Turn off the computer and other attached devices.
3.Determine whether the monitor will be desktop mounted or wall-mounted. See “Installing the Monitor” in this 
chapter.
4.Prepare a flat area to assemble the monitor. You may need a flat, soft, protected area for placing the monitor 
screen-down while preparing it for installation.
5.You need a Phillips...

Setting Up the Monitor
3-2User’s Guide 3.Lift the monitor to an upright position and place on a flat, stable surface.
Monitor in upright position
Preparing the monitor for wall-mounting
1.Disconnect the power cable and any other cables from the monitor.
2.Place the monitor face down on a flat, protected surface.
3.Release the base from the column by squeezing the two tabs toward each other. Pull the base away from the 
column as you do so.
Bottom view of monitor base showing release tabs (circled)...

Setting Up the Monitor
User’s Guide3-3 4.Remove the screws inside the support column as indicated.
Remove the screws inside the support column 
5.Rock the bottom of the support column until it snaps away from the top portion of the column, which covers the 
support column mounting bracket.
Snapping the bottom portion of the column from the top
6.Slide the top portion of the column up to expose the mounting bracket.
Removing the top portion of the column
7.Remove the four screws that secure the column...

Setting Up the Monitor
3-4User’s Guide
8.
Slide the column mounting bracket aw ay from the bottom of the monitor.
Sliding the column mounting bracket from the monitor
9. Remove the Compaq logo from the back of mo nitor to expose the top two threaded holes (A) and ( B) for the wall 
mount bracket. Place the tip of a small, flat  blade screwdriver under the logo to pry it up.
Removing the logo from the back of the monitor
Use the four holes ( A), ( B), ( C), and ( D) to attach the swing arm or other mo...

Setting Up the Monitor
User’s Guide3-5
Connecting the VGA (Analog) Cable
Use a VGA video cable to connect your Compaq flat-screen monitor to your computer.
Connecting the VGA cable
To connect the VGA cable
Connect one end of the VGA video cable to the back of  the monitor and the other end to the VGA video connector 
on the computer.
NOTE:  If your computer has a DVI connector and no VGA conn ector, use a DVI-I to VGA adapter to connect your 
computer to the monitor. Connect the DVI-I to VGA adapte r to...

Setting Up the Monitor
3-6User’s Guide
Audio and Video Cables and Adapters
The following table shows the cable and adapter types that may be required to connect the monitor to the computer, 
TV, or set-top box.
The number and type of cables required may vary by model. Some cables and adapters are included for select 
models only and may be sold separately.
Cable/Adapter NameDescription
VGA cable VGA transmits an analog video signal.
DVI-I to VGA adapter Connects a VGA monitor to a DVI connector on the...

Setting Up the Monitor
User’s Guide3-7
Connecting the Audio Cable
Connect the built-in monitor speakers to the computer by using the audio cable, as shown in the following illustration.
Connecting the audio cables—connector locations may vary
 

Setting Up the Monitor
3-8User’s Guide
Connecting the Power Cable
1.Read the warning below.
Connecting the power cable
2.Connect one end of the power cable to the monitor and the other end to a grounded electrical outlet.
WARNING: To reduce the risk of electric shock or damage to your equipment:
■Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the 
power cord into a grounded (earthed) electrical outlet.
■Be sure that the grounded power outlet you plug...

Setting Up the Monitor
User’s Guide3-9
Cable Management
Your Compaq LCD monitor provides cable management. Cables can be easily routed through the hollow section of 
the support column and are hidden when the monitor is viewed from the front.
Routing cables through the rear of the support column
 

Setting Up the Monitor
3-10User’s Guide
Adjusting the Tilt
For optimal viewing, adjust the screen tilt to your own preference, as follows:
1.Face the front of the monitor and hold the base so that you do not topple the monitor while changing the tilt.
2.Adjust the tilt by moving the top edge of the monitor either toward or away from you, without touching the 
screen.
Tilt adjustment