HP Compaq Le19f User Guide

							To use the auto-adjustment feature:
1.Allow the monitor to warm up for 20 minutes before adjusting.
2.Press the -/Auto button on the monitor front panel.
●You can also press the Menu button, then select Image Control from the OSD Main Menu.
Refer to 
Adjusting the Monitor Settings on page 15 in this chapter.
●If the result is not satisfactory, continue with the procedure.
3.Insert the CD in the disc drive. The CD menu is displayed.
4.Select Open Auto-Adjustment Software. The setup test pattern is displayed.
5.Press the -/Auto button on the monitor front panel to produce a stable, centered image.
6.Press the ESC key or any other key on the keyboard to exit the test pattern.
ENWW Using the Auto-Adjustment Function 13
 
						

							Front Panel Controls
Table 4-1  Monitor Front Panel Controls
Control Function
1MenuOpens, selects or exits the OSD menu.
2– (minus)/Auto●If the OSD menu is on, press to navigate backward
through the OSD menu and decrease adjustment
levels.
●If the OSD menu is inactive, press to activate the auto
adjustment feature to optimize the screen image.
3+ (plus)●Navigates forward through the OSD menu and
increases adjustment levels.
●When the OSD menu is inactive, an Input button
chooses the video input signal input, VGA or DVI (select
models have input select function).
4 Power LEDGreen = Fully powered.
Amber = Sleep mode.
Flashing Amber = Sleep Timer mode.
5Power Turns the monitor on or off.
14 Chapter 4   Operating the Monitor ENWW
 
						

							Adjusting the Monitor Settings
The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP Display
Assistant utility.
NOTE:If there is a problem with the display settings, try resetting the settings to the factory defaults
by opening the OSD and selecting Factory Reset from the OSD menu.
Using the On-Screen Display Menu
Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences. To
access the OSD, do the following:
1.If the monitor is not already on, press the Power button to turn on the monitor.
2.To access the OSD Menu, press the Menu button on the monitor’s front panel.
3.To navigate through the OSD Menu, press the + (Plus) button on the monitor’s front panel to scroll
up, or the – (Minus)/Auto button to scroll in reverse.
4.To select an item from the OSD Menu, use the + or – buttons to scroll to and highlight your selection,
then press the Menu button to select that function.
5.Adjust the item using the + or – buttons on the front panel to adjust the scale.
6.After adjusting the function, select Save and Return, or Cancel if you don’t want to save the setting,
then select Exit from the Main Menu.
NOTE:If the buttons remain untouched for 10 seconds while displaying a menu, new adjustments will
be discarded and the settings will revert to previous settings and exit the menu.
ENWW Adjusting the Monitor Settings 15
 
						

							OSD Menu Selections
The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions.
After changing an OSD menu item, and if the menu screen has these options, you may choose to:
●Cancel—to return to the previous menu level.
●Save and Return—to save all changes and return to the OSD Main Menu screen. This Save and
Return option is only active if you change a menu item.
Table 4-2  OSD Menu
IconMain MenuSubmenuDescription
BrightnessAdjustable scaleAdjusts the brightness level of the screen. The factory
default range is 90.
ContrastAdjustable scaleAdjusts the contrast level of the screen. The factory
default range is 80.
Volume (select
models with
internal speakers) Adjusts the monitors speaker volume level. The
factory default range is 50.
Image ControlAdjusts the screen image. (VGA input only)
Auto AdjustmentAutomatically adjusts the screen image.
Horizontal PositionAdjusts the position of the screen image left and right.
Vertical PositionAdjusts the position of the screen image up and down.
Custom Scaling (select
models)Selects the method on how displayed information on
the monitor will be formatted. Select:
●Fill to Screen - image fills the entire screen and
may look distorted or elongated because of non-
proportional scaling of height and width
●Fill to Aspect Ratio - image is sized to fit the
screen and maintains proportional image
●One-to-one (select models) - disables video
scaling, displays an image that is smaller in size
than the monitor’s capability and centers the
image on the screen in the active viewing area
Sharpness (select
models)Adjusts the screen image to look sharper or soft.
NOTE:If the one-to-one custom scaling menu is
selected, scaling is disabled and the sharpness
feature will also be disabled.
 Dynamic Contrast Ratio
(select models)Turns Dynamic Contrast Ratio On or Off. The factory
default is Off.
ClockMinimizes any vertical bars or strips visible on the
screen background. Adjusting the Clock will also
change the horizontal screen image.
Clock Phase Adjusts the focus of the display. This adjustment
allows you to remove any horizontal noise and clear or
sharpen the image of characters.
16 Chapter 4   Operating the Monitor ENWW
 
						

							IconMain MenuSubmenuDescription
ColorSelects the screen color. The factory default is 6500K
or Custom Color, depending on the model.
9300 KChanges to slightly blueish white.
6500 KChanges to slightly reddish white.
Custom ColorSelects and adjusts your own color scales:
●R—sets your own red color levels
●G—sets your own green color levels
●B—sets your own blue color levels
sRGBSets your screen colors to adapt to the color standards
used in the image technology industry.
Quick View Select the viewing mode.
  MovieSelect the movie mode.
  PhotoSelect the photo mode.
  GamingSelect the gaming mode.
  TextSelect the text mode.
  CustomSettings saved when user adjusts the Brightness,
Contrast, or Color in one of the Quick View options.
LanguageSelects the language in which the OSD menu is
displayed. The factory default is English.
ManagementSelects the OSD and power management features of
the monitor.
  OSD Control Adjusts the position of the OSD menu screen to:
●Horizontal OSD Position—Changes the viewing
position of the OSD menu to the left or right area
of the screen. The factory default range is 50.
●Vertical OSD Position—Changes the viewing
position of the OSD menu to the top or bottom
area of the screen. The factory default range is
50.
●OSD Transparency—Adjust to view the
background information through the OSD
●OSD Timeout—Sets the time duration in seconds
that the OSD is visible after the last button is
pressed. The factory default is 30 seconds.
●OSD Rotation (select models)—Rotates the OSD
Menu to support pivot function.
Table 4-2  OSD Menu (continued)
ENWW Adjusting the Monitor Settings 17
 
						

							IconMain MenuSubmenuDescription
Power SaverEnables the power saving feature. Select:
●On
●Off
The factory default is On.
Power On RecallRestores power to the monitor following an
unexpected removal of power. Select:
●On
●Off
The factory default is On.
Mode DisplayDisplays the resolution, refresh rate and frequency
information on the screen each time the OSD Main
Menu is accessed. Select:
●On
●Off
Depending on monitor model, factory default is On or
Off.
Power-On Status
DisplayDisplays the operating status of the monitor each time
the monitor is powered on. Select the location to
display the status to:
●Top
●Middle
●Bottom
●Off
The factory default is Top.
DDC/CI SupportAllows the computer to control some OSD menu
features such as brightness, contrast and color
temperature. Set to:
●On
●Off
The factory default is On.
  Bezel Power LED Turns off the power LED on the front panel of the
monitor. The factory default is On.
Table 4-2  OSD Menu (continued)
18 Chapter 4   Operating the Monitor ENWW
 
						

							IconMain MenuSubmenuDescription
Sleep TimerProvides the timer adjustment menu options:
●Set Current Time—sets the current time in hours
and minutes
●Set Sleep Time—sets the time you want to place
the monitor in sleep mode
●Set on Time—sets the time you want the monitor
to wake up from sleep mode
●Timer—sets the Sleep Timer feature On or Off.
The default setting is Off.
●Sleep Now—immediately sets the monitor to
enter sleep mode
Video Input
Control (select
models) Selects the video input signal. DVI is the factory
default.
 Switch Video InputSelects the other (VGA or DVI) video input signal.
Default is DVI.
 Auto-Switch InputTurns the systems automatic video signal input to on
or off. The factory default is On.
 Default Video InputSelects the default or primary video input signal when
the monitor is connected to two active and valid video
sources. The monitor will automatically determine the
video format. The default input selection is DVI.
Analog — VGA — Selects VGA input.
Digital — DVI — Selects DVI input.
InformationSelects and displays important information about the
monitor.
Current SettingsProvides the current input video mode.
Recommended
SettingsProvides the recommended resolution mode and
refresh rate for the monitor.
Serial NumberReports the serial number of the monitor. The serial
number is needed if contacting HP technical support.
VersionReports the firmware version of the monitor.
Backlight HoursReports the total hours of backlight operation.
  Service Support: http://
www.hp.com/support 
Factory ResetReturns all OSD menu settings and DDC/CI controls
to the factory default settings, except the Language.
Exit Exits the OSD menu screen.
Table 4-2  OSD Menu (continued)
ENWW Adjusting the Monitor Settings 19
 
						

							Optimizing Digital Conversion
Two controls in the on-screen display can be adjusted to improve image performance: Clock and Clock
Phase.
NOTE:The Clock and Clock Phase controls are adjustable only when using an analog input. These
controls are not adjustable for digital inputs.
The Clock must first be set correctly since the Clock Phase settings are dependent on the main Clock
setting. Use these controls only when the auto-adjustment function does not provide a satisfactory
image.
●Clock—Increases/decreases the value to minimize any vertical bars or stripes visible on the screen
background.
●Clock Phase—Increases/decreases the value to minimize video distortion or video jitter.
NOTE:When using the controls, you will obtain the best results by using the auto-adjustment pattern
software utility provided on the CD.
When adjusting the Clock and Clock Phase values, if the monitor images become distorted, continue
adjusting the values until the distortion disappears. To restore the factory settings, select Yes from the
Factory Reset menu in the on-screen display.
Using the HP Display Assistant Utility
HP Display Assistant, included on the software and documentation CD, is a software utility that guides
you through the tuning process with easy to understand instructions and background patterns designed
for each monitor control. It provides:
●Accurate screen calibration through the use of step-by-step instruction Wizards to obtain the best
overall image quality.
●Software control of the monitor image and color settings to eliminate dependence on the monitor’s
front panel buttons and On-Screen Display (OSD) menu.
●Defined preset display settings for each individual user in a multi-user environment.
●Multiple preset display settings for a single user based on content and ambient lighting.
●Asset Management and Power Management capabilities that include remote control for individual
or a group of displays on the domain from a centralized console application.
●Power Saving Plug-in feature that applies power saving modes to the display and a schedule power
saving feature that allows the display to be set to idle (stand-by) mode or powered off after a pre-
determined time of inactivity.
The HP Display Assistant Utility has two modes of operation: Wizard and OSD mode. The preferred
method of use is Wizard mode, which takes you through a step-by-step process to accurately calibrate
the monitor. This method relies on a sequence of steps that will obtain the best display results when
completed.
NOTE:Refer to the HP Display Assistant user guide for additional information about the software.
20 Chapter 4   Operating the Monitor ENWW
 
						

							Identifying Monitor Conditions
Special messages will appear on the monitor screen when identifying the following monitor conditions:
●Input Signal Out of Range—Change resolution setting to 1440 x 900 – 60Hz—Indicates the
monitor does not support the input signal because the resolution and/or refresh rate are set higher
than the monitor supports (models LE1901w/LE1901wm/LE19f).
●Input Signal Out of Range—Change resolution setting to 1680 x 1050 – 60Hz—Indicates the
monitor does not support the input signal because the resolution and/or refresh rate are set higher
than the monitor supports (model LE2201w).
●No Source Signal—Indicates the monitor is not receiving a video signal from the PC on the monitor
video input connector. Check to determine if the PC or input signal source is off or in the power
saving mode.
●Auto Adjustment in Progress—Indicates the auto-adjustment function is active.
●Monitor Going to Sleep—Indicates the screen display is entering a sleep mode.
●Check Video Cable—Indicates the video cable is not properly connected to the computer.
●OSD Lockout—The OSD can be enabled or disabled by pressing and holding the Menu button
on the front panel for 10 seconds. If the OSD is locked, the warning message OSD Lockout
displays for ten seconds.
◦If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.
◦If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.
●Power Button Lockout—Indicates the power button is locked. If the power button is locked, the
warning message Power Button Lockout displays.
◦If the power button is locked, press and hold the power button for 10 seconds to unlock the
power button function.
◦If the power button is unlocked, press and hold the power button for 10 seconds to lock out
the power button function.
●Theft Mode Enabled—Indicates that theft deterrence mode has been activated. Theft deterrence
is an optional feature that can be set up in HP Display Assistant. Theft deterrence mode is triggered
if both the power and display cables have been disconnected from the monitor, the monitor is
reconnected to a different computer, and the theft deterrence PIN number is not entered within the
elapsed time. When the monitor is in theft deterrence mode, all front panel buttons are disabled
other than the power button.
Sleep Timer Mode
The Sleep Timer mode is an energy-saving feature that enables you to set a time for the monitor to
power on and off at the same time every day. This also extends the life of the backlight bulbs in the
monitor. The Sleep Timer has five settings:
●Set Current Time
●Set Sleep Time
●Set On Time
ENWWIdentifying Monitor Conditions 21
 
						

							●Timer: On/Off
●Sleep Now
To set the timer:
1.Press the Menu button on the monitor front panel to display the OSD Menu.
2.Scroll down and highlight Management.
3.Press the Menu button to select Management.
4.Scroll down and highlight and select Sleep Timer > Set Current Time.
NOTE:You must set the current local time before you reset the time for Sleep Time or On
Time. Note that the time is displayed in a 24–hour clock format. For example, 1:15 p.m. is displayed
as 13 hours 15 minutes.
A power failure or loss of power to the monitor will cause the timer to reset to 00:00. If this occurs,
you will need to reset the sleep timer mode.
5.Press the Menu button once to enter the adjustment mode for hours.
6.Press the - (Minus) or + (Plus) button to adjust the hour.
7.Press the Menu button again to enter the time for minutes.
8.Press the - (Minus) or + (Plus) button to adjust the minutes.
9.Press the Menu button to lock in the time chosen.
10.After setting the current time, the highlight automatically skips to Set Sleep Time hours. Repeat
steps 6 through 9 to set Sleep Time.
11.If you do not want to set Sleep Time, press the Menu button twice, then select Save and
Return to exit the menu.
12.After setting Sleep Time, the highlight automatically skips to Set On Time hours. Repeat steps 6
through 9 to set On Time.
13.Set the Timer mode to On to activate the Sleep Timer settings.
14.When you are finished, select Save and Return to exit the menu.
The fifth selection, Sleep Now, turns the monitor backlights off immediately and stays in sleep mode
until the next On Time activates or a monitor button is pressed.
22 Chapter 4   Operating the Monitor ENWW