HP Color LaserJet CP6015de User Manual

SizeDimensionsStacking2Angled
staple (left-
angled)Angled
staple (right-
angled)Two staples
(top or side)FoldingSaddle stitch
A4210 x 297 mm (8.27
x 11.69 in)  
A4 Rotated297 x 210 mm
(11.69 x 8.27 in) 11
Executive184 x 267 mm (7.24
x 10.51 in)     
Executive (JIS)216 x 330 mm (8.5
x 13 in)     
A3297 x 420 mm
(11.69 x 16.54 in)11
A5148 x 210 mm (5.83
x 8.27 in)     
A6105 x 148 mm (4.13
x 5.83 in)     
Statement140 x 216 mm (5.5
x 8.5 in)     
11 x 17
(Ledger)279 x 432 mm (11 x
17 in)11
12 x 18305 x 457...

SizeDimensionsStacking2Angled
staple (left-
angled)Angled
staple (right-
angled)Two staples
(top or side)FoldingSaddle stitch
Banner(99 to 320 x up to
915 mm) (12.9 x
36 in)     
Envelope 9#98.4 x 225.4 mm
(3.88 x 8.88 in)     
Envelope 10#104.77 x 241.3 mm
(4.12 x 9.5 in)     
Envelope DL110 x 220 mm (4.33
x 8.66 in)     
Envelope C5162 x 229 mm (6.38
x 9.02 in)     
Envelope B5176 x 250 mm (6.93
x 9.84 in)     
Envelope C6114 x 162 mm (4.49
x 6.38 in)     
Envelope
Monarch98.42 x 190.5 mm
(3.88 x 7.5...

Supported paper types
Table 7-4  Tray 1 paper information
TypeSpecificationsQuantityDriver settingsPaper orientation
Paper and cardstock,
standard sizesRange:
60 g/m
2 (16 lb) bond to
220 g/m2 (58 lb) bond
Maximum stack height:
10 mm (0.6 in)
Equivalent to 100
sheets of 75 g/m
2 (20
lb) bond.
Plain or unspecifiedLoad preprinted or
prepunched paper
facing down, with the
bottom edge leading
into the tray, or toward
the front of the product
EnvelopesLess than 60 g/m2 (16
lb) bond to 90 g/m2 (24
lb) bond
Up...

TypeSpecificationsQuantityDriver SettingsPaper orientation
Heavy0.13 mm (0.005 in)
thickMaximum stack height:
54 mm (2.1 in)Light glossy, glossy, or
heavy glossySide to be printed on
facing up
GlossyRange:
75 g/m
2 (20 lb) bond to
220 g/m2 (58 lb) bond
Maximum stack height:
54 mm (2.1 in)Light glossy, glossy, or
heavy glossySide to be printed on
facing up
Photo media60 g/m2 (16 lb) bond to
220 g/m2 (58 lb) bond
Maximum stack height:
54 mm (2.1 in)Light glossy, glossy, or
heavy glossySide to be printed...

Special paper or print media guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory
results. When using special paper or print media, be sure to set the type and size in your print driver to
obtain the best print results.
CAUTION: HP LaserJet printers use fusers to bond dry toner particles to the paper in very precise
dots. HP laser paper is designed to withstand this  extreme heat. Using inkjet paper not designed for this
technology could damage...

Load paper and print media
You can load different media in the trays and then request media by type or size by using the control
panel.
Load Tray 1
CAUTION:To avoid jams, never add or remove  paper from Tray 1 during printing.
1.Open Tray 1.
2.Set the side guides to the correct width, and pull out the tray extensions to support paper.
3. Load paper in the tray with the side to be prin ted on face down and the top of the paper or non-
postage end facing the front of the printer.
NOTE: For Letter Rotated...

Print envelopes
If your software does not automatically format an envelope, specify Landscape for page orientation in
your software program or printer driver. Use the following guidelines to set margins for return and
destination addresses on Commercial #10 or DL envelopes:
Address typeLeft marginTop margin
Return15 mm (0.6 in)15 mm (0.6 in)
Destination 102 mm (4 in) 51 mm (2 in)
For envelopes of other sizes, adjust the margin settings accordingly.
Load banner paper into Tray 1
You can print banners from...

2.Adjust the paper-width guide by squeezing the ad justment latch and sliding the guide to the size
of the paper being used.
3. Adjust the paper-length guide by squeezing the adjustment latch and sliding the guide to the size
of the paper being used.
94 Chapter 7   Paper and print media ENWW
 

4.Load paper into the tray face up. Check the paper to  verify the guides lightly touch the stack, but
do not bend it.
NOTE: To prevent jams, do not overf ill the input tray. Be sure the top of the stack is below the
tray full indicator.
NOTE: For best performanc e, fill the tray complete ly without splitting the ream of paper. Splitting
the ream can cause a multifeed problem. The capacity of the paper tray can vary. For example, if
you are using 75 g/m
2 (20 lb) paper, the tray holds a full ream  of 500...

●SRA3 (Trays 3, 4, or 5 only)
● B5 (ISO)
● RA4
● SRA4
● 8K 270 x 390 mm
● 16K 195 x 270 mm
● 8K 260 x 368 mm
● 16K 184 x 260 mm
● 8K 273 x 394 mm
● 16K 197 x 273 mm
CAUTION:
Do not print envelopes or unsupported sizes  of paper from the 500-sheet trays. Print on
these types of paper only from  Tray 1. Do not overfill the input tray or open it wh ile it is in use. Doing so
can cause paper jams.
Load custom-size paper into Tray 2, 3, 4, or 5
To use custom media, change the size setting on the control panel...