HP 5500 Ei 5500 Si Switch Series Configuration Guide

 250 
Step Command Remarks 
2.  Enter interface view. 
• Enter Layer 2 Ethernet interface 
view or Layer 2 aggregate 
interface view:  
interface interface-type 
interface-number  
• Enter port group view: 
port-group  manual 
port-group-name   Use one of the commands. 
3.
  Configure the MVRP 
registration mode.  mvrp registration
 { fixed | 
forbidden  | normal  }  Optional. 
The default setting is normal 
registration mode.  
 
Configuring MRP timers 
 
 
CAUTION: 
The MRP timers apply to all MRP...

 251 
Table  28 shows the value ranges for Join, Leave, and LeaveAll timers and their dependencies.  
•   If you set a timer to a value beyond the allowed value range, your configuration will fail. To do that, 
you can change the allowed value range by tuning the value of another related timer. 
•   To restore the default settings of the timers, restore the Join timer first, followed by the Leave and 
LeaveAll timers.  
Table 28  Dependencies of the Join, Leave, and LeaveAll timers 
Timer Lower  limit...

 252 
Task Command Remarks 
Display the MVRP status of 
the specified port and each 
MVRP interface in the 
specified VLAN. display mvrp state interface
 interface-type 
interface-number  vlan  vlan-id  [ | { begin  | 
exclude  | include  } regular-expression ]  Available in any view 
Display the MVRP running 
status.  display mvrp running-status
 [ interface 
interface-list ] [ | { begin |  exclude | 
include  } regular-expression ]   Available in any view
 
Display the MVRP statistics.  display mvrp...

 253 
Figure 80 Network diagram 
 
 
Configuration procedure 
Configuring Device A 
# Enter MST region view. 
 system-view 
[DeviceA] stp region-configuration 
# Configure the MST region name, VLAN-to-instance mappings, and revision level. 
[DeviceA-mst-region] region-name example 
[DeviceA-mst-region] instance 1 vlan 10 
[DeviceA-mst-region] instance 2 vlan 20 
[DeviceA-mst-region] revision-level 0 
# Manually activate the MST region configuration. 
[DeviceA-mst-region] active region-configuration...

 254 
# Configure port GigabitEthernet1/0/2 as a trunk port, and configure it to permit VLAN 40. 
[DeviceA] interface gigabitethernet 1/0/2 
[DeviceA-GigabitEthernet1/0/2] port link-type trunk 
[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 40 
# Enable MVRP on port GigabitEthernet1/0/2. 
[DeviceA-GigabitEthernet1/0/2] mvrp enable 
[DeviceA-GigabitEthernet1/0/2] quit 
# Configure port GigabitEthernet 1/0/3 as a trunk port, and configure it to permit all VLANs. 
[DeviceA] interface gigabitethernet...

 255 
[DeviceB] interface gigabitethernet 1/0/2 
[DeviceB-GigabitEthernet1/0/2] port link-type trunk 
[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan all 
# Enable MVRP on port GigabitEthernet1/0/2. 
[DeviceB-GigabitEthernet1/0/2] mvrp enable 
[DeviceB-GigabitEthernet1/0/2] quit 
# Configure port GigabitEthernet 1/0/3 as a trunk port, and configure it to permit all VLANs. 
[DeviceB] interface gigabitethernet 1/0/3 
[DeviceB-GigabitEthernet1/0/3] port link-type trunk 
[DeviceB-GigabitEthernet1/0/3]...

 256 
# Enable MVRP on port GigabitEthernet1/0/2. 
[DeviceC-GigabitEthernet1/0/2] mvrp enable 
[DeviceC-GigabitEthernet1/0/2] quit 
Configure Device D: 
# Enter MST region view. 
 system-view 
[DeviceD] stp region-configuration 
# Configure the MST region name, VLAN-to-instance mappings, and revision level. 
[DeviceD-mst-region] region-name example 
[DeviceD-mst-region] instance 1 vlan 10 
[DeviceD-mst-region] instance 2 vlan 20 
[DeviceD-mst-region] revision-level 0 
# Manually activate the MST region...

 257 
 ----[GigabitEthernet1/0/1]----  
 Config  Status                      : Enabled 
 Running Status                      : Enabled 
 Join Timer                          : 20 (centiseconds) 
 Leave Timer                         : 60 (centiseconds) 
 Periodic Timer                      : 100 (centiseconds) 
 LeaveAll Timer                      : 1000 (centiseconds) 
 Registration Type                   : Normal 
 Local VLANs :  
  1(default), 
 
 ----[GigabitEthernet1/0/2]----  
 Config  Status...

 258 
 Periodic Timer                      : 100 (centiseconds) 
 LeaveAll Timer                      : 1000 (centiseconds) 
 Registration Type                   : Normal 
 Local VLANs :  
  1(default), 
 
 ----[GigabitEthernet1/0/2]----  
 Config  Status                      : Enabled 
 Running Status                      : Enabled 
 Join Timer                          : 20 (centiseconds) 
 Leave Timer                         : 60 (centiseconds) 
 Periodic Timer                      : 100 (centiseconds)...

 259 
 
 ----[GigabitEthernet1/0/2]----  
 Config  Status                      : Enabled 
 Running Status                      : Enabled 
 Join Timer                          : 20 (centiseconds) 
 Leave Timer                         : 60 (centiseconds) 
 Periodic Timer                      : 100 (centiseconds) 
 LeaveAll Timer                      : 1000 (centiseconds) 
 Registration Type                   : Normal  
 Local VLANs :  
  1(default), 20, 
The output shows that: 
{ Port GigabitEthernet 1/0/1...