HP 5500 Ei 5500 Si Switch Series Configuration Guide

 190 
[PE1-GigabitEthernet1/0/1-vid-200] quit 
[PE1-GigabitEthernet1/0/1] quit 
{ Configure GigabitEthernet 1/0/2: 
# Configure GigabitEthernet 1/0/2 as a trunk po rt and assign it to VLAN 100 and VLAN 200. 
[PE1] interface gigabitethernet 1/0/2 
[PE1-GigabitEthernet1/0/2] port link-type trunk 
[PE1-GigabitEthernet1/0/2] port trunk permit vlan 100 200 
# Set the TPID in the outer VLAN tags to 0x8200. 
[PE1-GigabitEthernet1/0/2] quit 
[PE1] qinq ethernet-type service-tag 8200 
 
 NOTE: 
The previous...

 191 
  NOTE: 
The previous command is available only on  the 5500 EI Switch Series. For how to confi
gure the TPID value
on the 5500 SI Switch Series, see  Configuring the TPID value on the 5500 SI .
   
3. Configure third-party devices: 
On the third-party devices between PE 1 and PE 2, configure the port that connects to PE 1 and that 
connecting to PE 2 to allow tagged frames  of VLAN 100 and VLAN 200 to pass through. 
Selective QinQ configuration example (configuring an outer 
VLAN tagging policy in...

 192 
 IMPORTANT: 
Make sure that you have configured the devices in the service provider network to allow QinQ packets to
pass through. 
 
1.
 Configure PE 1: 
{  Configure GigabitEthernet 1/0/1: 
# Configure GigabitEthernet 1/0/1 as a hybrid port to permit frames of VLAN 10 and VLAN 
20 to pass through tagged, and frames of  VLAN 100 and VLAN 200 to pass through 
untagged. 
 system-view 
[PE1] interface gigabitethernet 1/0/1 
[PE1-GigabitEthernet1/0/1] port link-type hybrid 
[PE1-GigabitEthernet1/0/1]...

 193 
[PE1-GigabitEthernet1/0/2] port trunk permit vlan 100 200 
# Set the TPID in the outer VLAN tags to 0x8200. 
[PE1-GigabitEthernet1/0/2] quit 
[PE1] qinq ethernet-type service-tag 8200 
2. Configure PE 2: 
{  Configure GigabitEthernet 1/0/1: 
# Configure GigabitEthernet 1/0/1 as a hybrid port to permit frames of VLAN 10 and VLAN 
20 to pass through tagged, and frames of  VLAN 100 and VLAN 200 to pass through 
untagged. 
[PE2] interface gigabitethernet 1/0/1 
[PE2-GigabitEthernet1/0/1] port link-type...

 194 
# Set the TPID in the outer VLAN tags to 0x8200. 
[PE2-GigabitEthernet1/0/2] quit 
[PE2] qinq ethernet-type service-tag 8200 
3. Configure third-party devices: 
On the third-party devices between PE 1 and PE 2,  configure the port that connects to PE 1 and the 
port that connects to PE 2 to allow tagged fr ames of VLAN 100 and VLAN 200 to pass through. 
Selective QinQ configuration example (inner VLAN ID 
substitution) 
 
 IMPORTANT: 
This configuration example is available only on the 5500 EI...

 195 
 
1. Configure PE 1: 
{  Configure GigabitEthernet 1/0/1: 
# Configure GigabitEthernet 1/0/1 as a hybrid port to permit frames of VLAN 10 and VLAN 
20 to pass through tagged, and frames of  VLAN 100 and VLAN 200 to pass through 
untagged. 
 system-view 
[PE1] interface gigabitethernet 1/0/1 
[PE1-GigabitEthernet1/0/1] port link-type hybrid 
[PE1-GigabitEthernet1/0/1] port hybrid vlan 10 20 tagged 
[PE1-GigabitEthernet1/0/1] port hybrid vlan 100 200 untagged 
[PE1-GigabitEthernet1/0/1] quit 
#...

 196 
[PE1] traffic classifier A100 
[PE1-classifier-A100] if-match customer-vlan-id 10 
[PE1-classifier-A100] if-match service-vlan-id 100 
[PE1-classifier-A100] quit 
# Configure traffic behavior  T100 to mark matching pac kets with CVLAN 30. 
[PE1] traffic behavior T100 
[PE1-behavior-T100] remark customer-vlan-id 30 
[PE1-behavior-T100] quit 
# Create class A200 and configure the class to match frames with CVLAN 20 and SVLAN 
200. 
[PE1] traffic classifier A200 
[PE1-classifier-A200] if-match...

 197 
[PE2-behavior-P100] quit 
# Create class  A40 and configure the class to match frames with CVLAN 40. Create traffic 
behavior  P200 and add the action of inserting outer VLAN tag 200. 
[PE2] traffic classifier A40 
[PE2-classifier-A40] if-match customer-vlan-id 40 
[PE2-classifier-A40] quit 
[PE2] traffic behavior P200 
[PE2-behavior-P200] nest top-most vlan-id 200 
[PE2-behavior-P200] quit 
# Create a QoS policy named  qinq, associate traffic class  A30 with traffic behavior  P100, and 
associate...

 198 
# Create a QoS policy named  sqinq, associate traffic class A100 with traffic behavior  T100, 
and associate traffic class  A200 with traffic behavior  T200. 
[PE2] qos policy sqinq 
[PE2-qospolicy-sqinq] classifier A100 behavior T100 
[PE2-qospolicy-sqinq] classifier A200 behavior T200 
[PE2-qospolicy-sqinq] quit 
# Apply QoS policy  sqinq to the outgoing traffic on the port. 
[PE2] interface gigabitethernet 1/0/2 
[PE1-GigabitEthernet1/0/2] qos apply policy sqinq outbound 
# Set the TPID value in...

 199 
Configuring VLAN mapping (available only on 
the 5500 EI) 
Overview 
VLAN mapping re-marks VLAN tagged traffic with new VLAN IDs. HP provides the following types of 
VLAN mapping: 
•  One-to-one VLAN mapping —Replaces one VLAN tag with another. You can use one-to-one VLAN 
mapping to sub-classify traffic from a particular VLAN for granular QoS control. 
•   Many-to-one VLAN mapping — Re p l a c e s  m u l t i p l e  V L A N  t a g s  wi t h  t h e  s a m e  V L A N  t a g.  Yo u  c a n  u s e...