HP 5500 Ei 5500 Si Switch Series Configuration Guide

 130 
      Packet(s) arrived late: 0 
# Display the history of DNS tests. 
[DeviceA] display nqa history admin test 
  NQA entry (admin admin, tag test) history record(s): 
    Index      Response     Status           Time 
    1          62           Succeeded        2011-01-10 10:49:37.3 
FTP test configuration example 
Network requirements 
As shown in  Figure 43, configure NQA FTP tests to test the connection with a specific FTP server and the 
time required for Device A to upload a file to the FTP...

 131 
[DeviceA] display nqa result admin test 
  NQA entry (admin admin, tag test) test results: 
    Destination IP address: 10.2.2.2 
      Send operation times: 1              Receive response times: 1 
      Min/Max/Average round trip time: 173/173/173 
      Square-Sum of round trip time: 29929 
      Last succeeded probe time: 2011-01-22 10:07:28.6 
    Extended results: 
      Packet loss in test: 0% 
      Failures due to timeout: 0 
      Failures due to disconnect: 0 
      Failures due to no...

 132 
[DeviceA-nqa-admin-test-http] url /index.htm  
# Configure the HTTP version 1.0 to be used in HTTP tests. (Version 1.0 is the default version, and this step 
is optional.) 
[DeviceA-nqa-admin-test-http] http-version v1.0 
# Enable the saving of history records. 
[DeviceA-nqa-admin-test-http] history-record enable 
[DeviceA-nqa-admin-test-http] quit 
# Start HTTP tests. 
[DeviceA] nqa schedule admin test start-time now lifetime forever 
# Stop HTTP tests after a period of time. 
[DeviceA] undo nqa...

 133 
Configuration procedure 
Before you make the configuration, make sure the devices can reach each other. 
1. Configure Device B: 
# Enable the NQA server, and configure a listenin g service to listen to IP address 10.2.2.2 and 
UDP port 9000. 
 system-view 
[DeviceB] nqa server enable 
[DeviceB] nqa server udp-echo 10.2.2.2 9000 
2.  Configure Device A: 
# Create a UDP jitter test group. 
 system-view 
[DeviceA] nqa entry admin test 
[DeviceA-nqa-admin-test] type udp-jitter 
# Configure UDP jitter...

 134 
      Positive SD sum: 52                    Positive DS sum: 38 
      Positive SD average: 10                Positive DS average: 10 
      Positive SD square sum: 754            Positive DS square sum: 460\
 
      Min negative SD: 1                     Min negative DS: 6 
      Max negative SD: 13                    Max negative DS: 22 
      Negative SD number: 4                  Negative DS number: 5 
      Negative SD sum: 38                    Negative DS sum: 52 
      Negative SD average:...

 135 
      Negative SD average: 13                Negative DS average: 14 
      Negative SD square sum: 46994          Negative DS square sum: 303\
0 
    One way results: 
      Max SD delay: 46                       Max DS delay: 46 
      Min SD delay: 7                        Min DS delay: 7 
      Number of SD delay: 410                Number of DS delay: 410 
      Sum of SD delay: 3705                  Sum of DS delay: 3891 
      Square sum of SD delay: 45987          Square sum of DS delay:...

 136 
[DeviceA-nqa-admin-test-snmp] quit 
# Start SNMP tests. 
[DeviceA] nqa schedule admin test start-time now lifetime forever 
# Stop the SNMP tests after a period of time. 
[DeviceA] undo nqa schedule admin test 
# Display the results of the last SNMP test. 
[DeviceA] display nqa result admin test 
  NQA entry (admin admin, tag test) test results: 
    Destination IP address: 10.2.2.2 
      Send operation times: 1              Receive response times: 1 
      Min/Max/Average round trip time:...

 137 
[DeviceB] nqa server tcp-connect 10.2.2.2 9000 
2. Configure Device A: 
# Create a TCP test group. 
 system-view 
[DeviceA] nqa entry admin test 
[DeviceA-nqa-admin-test] type tcp 
# Configure TCP probe packets to use 10.2.2.2 as the destination IP address and port 9000 as 
the destination port. 
[DeviceA-nqa-admin-test-tcp] destination ip 10.2.2.2 
[DeviceA-nqa-admin-test-tcp] destination port 9000 
# Enable the saving of history records. 
[DeviceA-nqa-admin-test-tcp] history-record enable...

 138 
Figure 48  Network diagram 
 
 
Configuration procedure 
Before you make the configuration, make sure the devices can reach each other. 
1. Configure Device B: 
# Enable the NQA server, and configure a listenin g service to listen to IP address 10.2.2.2 and 
UDP port 8000. 
 system-view 
[DeviceB] nqa server enable 
[DeviceB] nqa server udp-echo 10.2.2.2 8000 
2.  Configure Device A: 
# Create a UDP echo test group. 
 system-view 
[DeviceA] nqa entry admin test 
[DeviceA-nqa-admin-test] type...

 139 
      Failures due to other errors: 0 
      Packet(s) arrived late: 0 
# Display the history of UDP echo tests. 
[DeviceA] display nqa history admin test 
  NQA entry (admin admin, tag test) history record(s): 
    Index      Response     Status           Time 
    1          25           Succeeded        2011-01-22 10:36:17.9 
Voice test configuration example 
Network requirements 
As shown in  Figure 49, configure NQA voice tests to test the delay jitter of voice packet transmission and 
voice...