HP 2310ti User Guide

cord does not exceed the rating of the cord. Look on the power label to determine the ampere
rating (AMPS or A) for each device.
●Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping
the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
●Turn the monitor off when not in use. You can substantially increase the life expectancy of the
monitor by using a screen saver program and turning off the monitor when not in use....

3 Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other
attached devices, then follow the instructions below.
Rear Components
HP 2310t Model
Figure 3-1  2310t Rear Components
Table 3-1  2310t Rear Components
Component Function
1 Cable Lock Provision Provides slot for use with cable security locks.
2 AC Power Connector Connects the AC power cord to the monitor.
3 Audio Connector Connects the audio cable to the monitor.
4 HDMI Connector...

HP 2310ti Model
Figure 3-2  2310ti Rear Components
Table 3-2  2310ti Rear Components
Component Function
1 Cable Lock Provision Provides slot for use with cable security locks.
2 AC Power Connector Connects the AC power cord to the monitor.
3 Audio Connector Connects the audio cable to the monitor.
4 DVI-D Connector Connects the DVI-D cable to the monitor.
5 VGA Connector Connects the VGA cable to the monitor.
6 USB Upstream Connector Connects the monitor USB cable to a host computer for
touch screen...

Routing the Cables
Before connecting the cables, route them through the cable routing hole in the center of the stand.
Figure 3-3  Routing Cables
Connecting the Cables
CAUTION:Before connecting cables to the monitor, ensure that the computer and the monitor are
powered off.
Connecting the VGA (Analog) Video Cable (HP 2310ti Model Only)
For analog operation, connect one end of a VGA signal cable (sold separately) to the VGA connector
on the rear of the monitor and the other end to the VGA connector on the...

Connecting the DVI-D (Digital) Video Cable
For DVI digital operation, connect one end of the provided DVI-D signal cable to the DVI connector on
the rear of the monitor and the other end to the DVI connector on the computer.
Figure 3-5  Connecting the DVI-D Cable
Connecting the HDMI (Digital) Video Cable (HP 2310t Model Only)
For HDMI digital operation, connect one end of an HDMI signal cable (sold separately) to the rear of
the monitor and the other end to a computer or other device with an HDMI...

Connecting the Audio Cable
Connect one end of the provided audio cable to the Audio In connector on the rear of the monitor and
the other end to the Audio Out connector on the computer.
NOTE:If you connect an HDMI cable (2310t model only) between the monitor and computer, you
do not need to connect the audio cable. The HDMI cable supports audio and video digital signals.
Figure 3-7  Connecting the Audio Cable
Connecting the USB Cable
Connect one end of the provided USB cable to the USB upstream connector...

Connecting the Power Cord
Connect one end of the power cord to the AC power connector on the rear of the monitor, and the
other end to an electrical wall outlet.
Figure 3-9  Connecting the Power Cord
WARNING!To reduce the risk of electric shock or damage to the equipment:
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
Disconnect power from the equipment...

2.Adjust the tilt by moving the top edge of the monitor either toward or away from you, without
touching the screen. The monitor will tilt forward 5 degrees and back 55 degrees.
Figure 3-10  Adjusting the Tilt
10 Chapter 3   Setting Up the Monitor ENWW
 

Keyboard Parking
If you need more space on your desktop, place the keyboard under the monitor when not in use.
Figure 3-11  Keyboard Parking
Turning on the Monitor
1.Press the power button on the computer to turn it on.
2.Press the power button on the front of the monitor to turn it on.
CAUTION:Burn-in image damage may occur on monitors that display the same static image on
screen for a prolonged period of time.* To avoid burn-in image damage on the monitor screen, you
should always activate a screen...

Removing the Monitor Pedestal Base
You can remove the monitor panel from the pedestal base to mount the panel on a wall, a swing arm,
or other mounting fixture (purchased separately).
CAUTION:Before beginning to disassemble the monitor, be sure the monitor is turned off and the
power and signal cables are both disconnected. Also disconnect the USB and audio cables if they are
connected to the monitor.
1.Disconnect and remove all cables from the back of the monitor.
2.Lay the monitor face down on a flat...