HP 2210m User Guide

Icon Main Menu Options Sub-menu Options Description
    Default Source Selects the default or primary video
input signal when the monitor is
connected to two active and valid video
sources. The monitor will automatically
determine the video format.
    Auto Switch Source Turns the systems automatic video
signal input to On or Off. The factory
default is On.
Selecting Video Input Connectors
The input connectors are:
●VGA connector (analog)
●DVI-D connector (digital) (select models)
●HDMI connector (select...

If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.
If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.
●Dynamic Contrast Ratio ONIndicates DCR is applied when Movie mode is selected from the
Quick View options.
●Dynamic Contrast Ratio OFFIndicates DCR has been turned off when the monitor is changed
to another viewing mode.
●No Input Signal — Indicates the monitor is not receiving a video signal from the computer on
the monitor video...

Power-Saver Feature
When the monitor is in normal operating mode, the Power light is green and the monitor uses the
normal watts of power. For power usage, refer to Technical Specifications (Appendix B).
The monitor also supports a power-saver mode that is controlled by the computer. When the monitor
is in the reduced-power state, the monitor screen is blank, the backlight is off, and the Power light is
amber. The monitor uses minimum power. When the monitor is awakened, a brief warm-up period
occurs...

A Troubleshooting
Solving Common Problems
The following table lists possible problems, the possible cause of each problem, and the
recommended solutions:
Problem Solution
Power LED is not on. Make sure the Power button is on, and the power cord is properly connected to a grounded
power outlet and to the monitor.
Select Management in the OSD menu, and then select Bezel Power LED. Check if the
Bezel Power LED option is set to Off and, if so, set to On mode.
Screen is blank. Connect the power cord. Turn on...

Problem Solution
Unable to hear audio from
built-in speakers.
Do the following:
●Ensure the source signal is good by using headphones at the source.
●Press the Menu button to access the OSD menu. Select Management, and then select
Volume to adjust the volume.
●Turn up the volume with the Volume button.
●Ensure speaker volume is not muted or too low: Click the Windows start button™,
Control Panel, and Hardware and Sound. Under Audio Devices and Sound, click
Adjust system volume. Under Main Volume, move...

Have the following information available when you call:
●Monitor model number (located on label on back of monitor)
●Monitor serial number (located on label on back of monitor or in the OSD display in the
Information menu)
●Purchase date on invoice
●Conditions under which the problem occurred
●Error messages received
●Hardware configuration
●Name and version of hardware and software you are using
Locating the Rating Label
The rating label on the monitor provides the product number and serial number. You...

B Technical Specifications
All specifications represent the typical specifications provided by HPs component manufacturers;
actual performance may vary either higher or lower.
HP LCD Monitors
Face treatment: Glare polarizer with hard coating
Input terminal:
●VGA connector
●DVI-D 24–pin D-type connector (select models)
●HDMI connector (select models)
Table B-1  Model 1910m
Specifications: 
Display Type: TFT LCD active matrix
Viewable Image Size: 47.0 cm (18.5 in.) diagonal
Tilt –5° to +25°
Maximum Weight...

Specifications: 
Operating Humidity: 20% to 80%
Non-Operating Humidity: 5% to 95%
Power Source: 100–240 V AC (ca), 50/60 Hz
Power Consumption: 28.5 watts (W) maximum
Sleep Power Consumption: 

Specifications: 
Tilt –5° to +25°
Maximum Weight (unpacked): 5.52 kg (12.2 lb)
Dimensions (h x w x d): 392 x 536 x 200 mm (15.4 x 21.1 x 7.9 in.)
Maximum Graphics Resolution: 1920 x 1080 @ 60 Hz analog mode
Optimum Graphics Resolution: 1920 x 1080 @ 60 Hz analog mode
Text Mode: 720 x 400
Dot Pitch: 0.2480 x 0.2480 mm
Horizontal Frequency (analog mode): 24 to 94 kHz
Vertical Frequency (analog mode): 50 to 76 Hz
Environmental Requirements
Temperature (independent of altitude)
Operating Temperature: 5° to...

Specifications: 
Temperature (independent of altitude)
Operating Temperature: 5° to 35° C (41° to 95° F)
Non-Operating Humidity: –20° to 60° C (–4° to 140° F)
Relative Humidity (non-condensing):
Operating Humidity: 20% to 80%
Non-Operating Humidity: 5% to 95%
Power Source: 100–240 V AC (ca), 50/60 Hz
Power Consumption: 56 watts (W) maximum
Sleep Power Consumption: