Honeywell Rlv4305a1000e Manual

RLV4305
Programmable Thermostat
Owner’s 
Guide
69-2613ES-01.book  Page -1  Thursday, November 10, 2011  11:38 AM 

Overview
About your new thermostat ................................................................... 1
Controls ................................................................................................. 2
Display................................................................................................... 3
Installation
Installation guidelines ............................................................................ 4
Wiring...

RLV4305
1 This thermostat is designed to control an electric heating system such as a
baseboard heater, a radiant ceiling, a convector or a fan-forced heater.
The thermostat CANNOT be used with:
• a resistive load under 0.83 A
• a resistive load over 14.6 A
• a system driven by a contactor or a relay (inductive load)
• a central heating system
SUPPLIED PARTS
• One (1) thermostat
• Two (2) 6-32 mounting screws
• Two (2) solderless connectors
About your new thermostat
Do you need assistance?
We are here to...

Owner’s Guide
2
Controls
Mode button 
(see pages 8 & 10)Day button
Hour button
Program button Minute button
Up and Down buttonsReturn button
Backlit screen *
* The screen is backlit for 12 seconds when you press any button.
69-2613ES-01.book  Page 2  Thursday, November 10, 2011  11:38 AM 

RLV4305
3
Display
Room temperature
Heating intensity indicator Time and day
Mode indicator 
(see pages 8 & 10) Appears when power to 
the thermostat is cut off 
(see page 7)
Setpoint 
temperature *
Appears if the 
thermostat is configured 
for a fan-forced heater 
(see page 11)
Period indicator
(see page 8)
Indicates that the settings 
are locked (see page 11)
* To display the set temperature (setpoint), press the Up or Down
button once. The thermostat will display the setpoint instead of the
clock for 5...

Owner’s Guide
4
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN
POWER PANEL TO AVOID ELECTRICAL SHOCK.
All cables and connections must comply with local electrical
codes.
This thermostat has tinned copper wires for line and load connec-
tions. Special CO/ALR solderless connectors must be used if
these wires will be connected to aluminium conductors.
Install the thermostat onto an electrical box.
Install the thermostat about 5’ (1.5 m) high, on an inside wall facing
the heater.
Avoid locations where...

RLV4305
5
Connect the thermostat wires to the power and to the load using
solderless connectors for copper wires.
Wiring
2-wire Installation
4-wire Installation
69-2613ES-01.book  Page 5  Thursday, November 10, 2011  11:38 AM 

Owner’s Guide
6
1)Push the excess wires back inside 
the electrical box.
2)Secure the thermostat to the 
electrical box using the provided 
screws.
3)Insert the screws through either the 
right or left pair of mounting holes 
on the thermostat.
NOTE: If there is a protective film or
sticker on the thermostat’s screen, peel it
off.
4)Apply power to the heating system. Verify the installation by 
checking that the heater can be turned on by raising the setpoint 
using the Up button and off by lowering the...

RLV4305
7
1)Press the Day button 
to set the day.
2)Use the Hour and Min 
buttons to set the 
clock.
3)Press the   button to 
exit.
Clock and day setting
The clock must be set 
when the time is incorrect 
or flashes on the screen.
69-2613ES-01.book  Page 7  Thursday, November 10, 2011  11:38 AM 

Owner’s Guide
8
In Automatic mode, the thermostat adjusts its temperature set-
point according to the period of the day. To place the thermostat in
this mode, press the Mode button until Auto appears on the
screen. The current period name also appears (unless the ther-
mostat has not been programmed with a schedule).
You can program up to 4 periods (Wake, Leave, Return or Sleep)
in a day. You can set 2 different programs: one for the weekdays
(Monday to Friday) and another one for the weekend (Saturday...