Honeywell Netaxs 4 Manual

NetAXS™ Access Control Unit User’s Guide, Document 800-04410, Revision A 1
1
Connecting to the Web Server
In this chapter...
1.1  Overview
A NetAXS™ access control site is configured with a host system and NetAXS™ 
access control units that exceed existing N-1000-III/IV, Pro Series specifications and 
approvals, and that communicate with each other and with a variety of input and 
output devices. Each access control unit, or panel, has four reader ports. See the 
NetAXS™ NX4L1 Installation Guide, NetAXS™...

2www.honeywell.com Connecting to the Web Server
Connecting to the Web Server
1.2  Connecting to the Web Server
This section describes how to connect a computer to the NetAXS™ web server via Ethernet and 
Internet Explorer. 
Notes:
• The NetAXS™ panel that you are connecting to the computer is the Gateway panel. DIP switch 
6 on a Gateway panel must be set to ON for a successful connection.
• The Microsoft Windows™ screen captures used in this section reflect the Windows 2000™ 
platform. If you are using...

Connecting to the Web Server
Connecting to the Web Server
NetAXS™ Access Control Unit User’s Guide, Document 800-04410, Revision A 3
Figure 1-2:  NetAXS™ Web Server Direct Connection
2. Configure the computer’s network connection:
a. Select 
Start > Settings > Control Panel.
b. Click Network and Dial-up Connections.
Terminal
NetAXS PanelEthernet Port
Ethernet
Cable 

4www.honeywell.com Connecting to the Web Server
Connecting to the Web Server
c. Identify your local Ethernet connection (commonly labeled Local Area Connection), and 
right click the icon to display the Local Area Connection Properties screen.
d. Highlight the Internet Protocol (TCP/IP) connection.
e. Click 
Properties to display your system’s current Internet Protocol properties.
f.
Important: Keep a record of your computer’s current network configuration as it appears 
in this screen. You will need to...

Connecting to the Web Server
Connecting to the Web Server
NetAXS™ Access Control Unit User’s Guide, Document 800-04410, Revision A 5
j. Click OK to accept the entries.
3. Open your browser (Internet Explorer shown below), and enter https://192.168.1.150 as the 
target address. 

6www.honeywell.com Connecting to the Web Server
Connecting to the Web Server
4. Press the Enter key to display the Honeywell NetAXS™ login screen.
Note: If you are using Microsoft Internet Explorer 7, and you receive a certificate error 
message, follow these steps to clear it: 
a. Enter the IP Address of the panel into the URL box.
b. Click Continue to the website (not recommended) to display the login screen.
c. Click Certificate Error at the top-right of the IP Address. The “Untrusted Certificate”...

Connecting to the Web Server
Reading the Select Panel
NetAXS™ Access Control Unit User’s Guide, Document 800-04410, Revision A 7
1.3  Reading the Select Panel
The Select Panel is located at the right margin of the NetAXS™ web server main screen, shown in the 
preceding section. The presence of a number in one of the Select Panel cells indicates that its 
associated panel is online. For example, if you see a number 1 in a cell, this indicates that panel 1 is 
online. The combinations of size and color of...

8www.honeywell.com Connecting to the Web Server
Reading the Select Panel
Large white number on blue background, such as 
“2” in the example below:Panel 2 is selected, and it has no unacknowledged 
alarms.
Small white number on a red background, such as 
“1” in the example below:Panel 1 is not selected, but it does have 
unacknowledged alarms.
Table 1-1:  Reading the Select Panel (continued)
Cell Display Status 

NetAXS™ Access Control Unit User’s Guide, Document 800-04410, Revision A9
2
Configuring via the Web Server
In this chapter...
Overview 10
Configuring the System 11
Configuring the Doors 31
Configuring Other I/O & Groups Tab 52
Configuring Interlocks 59
Configuring Time Management 24
Configuring Access Levels 45
Configuring Users 61 

10www.honeywell.com Configuring via the Web Server
Configuring the System
2.1  Overview
This chapter explains the NetAXS™ configuration functions as accessed via the NetAXS™ web 
server. These functions should be performed only by the NetAXS™ system administrator or service 
personnel.
Caution: The sequence of NetAXS™ configuration tasks is critical. If the sequence given below is not 
followed, the NetAXS™ system cannot be successfully configured.
The flow chart in Figure 2-1 shows the order in which to...