Honeywell keypad with Voice 6150V 6160V User Manual

							K0022UGV1  12/01  Rev. C 
 
 
ADEMCO 6150V & 6160V 
Voice Remote Keypad 
USER GUIDE 
This document provides Operating Instructions for your Keypad’s voice features.  Refer to your 
security system User Guide for all other security system functions and operating procedures.   
Message Center  The ADEMCO 6150V/6160V Keypads feature a 
voice message center that lets you record and 
playback one message.  
•  The message can be up to 2.5-minutes long 
•  The message remains in the Keypad’s 
memory until a new message is recorded.   
•  The volume control of the message is 
adjustable. 
•  Refer to the procedures below when using the 
Message Center functions.
 
1OFF
4MAX
7INSTANT
READY
2AWAY
5TEST
8CODE
03
STAY
6BYPASS
9CHIME
#
ARMED
READY
6160V-00-005-V1
MESSAGE
MICRECORD
VOLUME
PLAY
STATUS
VOICE
FUNCTION
VOLUME
KEY
VOICE
KEY
STATUS
KEYFUNCTION
KEYDOWN
VOLUME PLAY KEY
AND
UP VOLUME RECORD
KEY SPEAKER
LCD
DISPLAY
MICROPHONE
LEDs
 
To record a message: Press [#] FUNCTION + [0] VOICE + [1] RECORD keys.    The red MESSAGE indicator will light, indicating record in progress. 
 Note:  A message cannot be recorded during the Exit Delay period.   
To end recording:   Press [1] RECORD key. 
   The red MESSAGE LED will flash indicating a message waiting to be 
played.  After the message is played once the MESSAGE LED will go 
out.   
To play a message:   Press [#] FUNCTION + [0] VOICE + [3] PLAY keys. 
   The recorded message plays and the red MESSAGE LED turns off.  The 
recorded message will remain in memory until a new message is 
recorded.   
To adjust the volume: Press [#] FUNCTION + [0] VOICE + [2] VOLUME keys,  
  then press the desired volume control key [3] ↑ (up) or [6] ↓ (down).   
  Note:   
• Adjusting message volume also adjusts status volume.  Volume 
cannot be adjusted while playing a message.   
• Each time you enter the command to adjust the volume, the word 
“CHECK” will be heard to verify the current setting.   
(Continued on Other Side)  
						

							 
Chime and Status Features 
Voice Chime 
You can set each Keypad to announce faulted (opened) entry/exit or perimeter zones whenever 
the control panel’s Chime mode is on by turning on the Voice Chime mode. 
Voice Chime On/Off:  Press the [#] FUNCTION + [0] VOICE + [2] VOLUME + [4] keys. 
  When on, any faulted zone(s) causes a voice status annunciation, chime, 
and display. When off, the sounder will still provide chime when the 
control’s Chime mode is on.   
Voice Status 
You can use the STATUS key to announce system status and display any system and/or zone 
faults (if they exist) by first turning on the Voice Chime mode (see above).  When Voice Chime 
mode is on, pressing the STATUS key displays and announces current system status and zone 
descriptors (programmed by your installer) of faulted zones. If zone descriptors are not 
programmed, the respective faulted zone numbers are announced. 
To Announce Status:   Press the [#] FUNCTION + [0] VOICE + [] STATUS key once 
(Voice 
Chime mode must be “on”; see above)
.   The respective system status is announced (e.g. “Disarmed Ready to 
Arm” or “Disarmed Not Ready to Arm”).   
 Note:  Status cannot be announced during the Exit Delay period.   
To Announce Faults: Press the [] STATUS key a second time within 10 seconds of the first 
press. 
  Up to 3 faulted zones are announced with their zone descriptors, if 
programmed. If zone descriptors are not programmed, the respective 
zone numbers are announced. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ÊK0022UGV14Š 
K0022UGV1  12/01  Rev. C 
 
2 Corporate Center Drive, Suite 100 
P.O. Box 9040, Melville, NY 11747 
Copyright © 2004 Honeywell International Inc. 
www.honeywell.com/security