Honeywell Galaxy 3144 User Guide

3
SETTING THE SYSTEM
Before Setting
Before setting the system ensure all doors and windows are secured
and areas protected by movement detectors are free from obstruction.
Entering A Pin - User Type 2.1 - 2.2
As each digit is entered the keypad responds with a bleep and displays
a *. When all the digits are entered, press the ent or A > key to start the
setting routine.
Entering A Pin - User Type 2.3 - 3.6
As each digit is entered the keypad responds with a bleep and displays
a *. When all the digits are...

4
Sounder
During the setting period the sounder emits a continuous tone if all of
the zones are closed. If a zone is opened during the setting period, the
sounder begins to pulse. The sounder also pulses during the last 25%
of the setting time to indicate time running short.
Zones Open
The exit time will reset should any zones be open or opened during
setting. The display will indicate the number of zones open and invite
viewing. Closing the zones will restart the exit time. An alarm will be
generated if...

5
MAX SETTING OPTIONS
Setting with User Cards/Tags/Fobs
MAX user cards/tags/fobs can be used to set the system. This is done by assigning a MAX
user card (tag or fob) with one of the setting options. When the MAX card is held against a
MAX module for five seconds, the MAX function is activated. For example, if the MAX
function assigned is 13 = Part Set, then activating the card held function results in the system
being part set.
If a user is assigned group choice, then a keypad will have to be accessed...

6
UNSETTING THE SYSTEM
Normal Entry
Unsetting starts immediately when the FINAL door is opened or an
ENTRY zone is activated. The sounder pulses slowly and the user must
go directly to the keypad and enter a valid PIN, followed by  A>,  or < B. Press ent to
return to the banner. Certain types of alarms, once cancelled, require a
code with the appropriate reset authorisation to be entered. The system
prompts for a valid reset code by displaying Manager Reset Re-
quired or Engineer Reset Required on the...

7
Fault and Tamper Conditions
When a fault or tamper condition occurs in the unset state, an alert condition is activated.
This consists of an intermittent beep at the keypad and/or a visual alert on the keypad. A user
should enter their code at the keypad and press ent. The condition causing the fault or
tamper will be shown. Use the A>and 

8
MENU OPTIONS
The Galaxy 3 Series provides various menu options for modifying the functional perform-
ance of the system.
There are two menu structures:
Full Menu
Only accessed by authorised users including the master manager code and by the engineer.
Quick Menu
A selection of options from the full menu. The quick menu is the default menu access for all
user codes (type 2.3 and above) except the master manager and engineer.
Table 1. Menu Options
e p y T r e s Uu n e M k c i u Qu n e M l l u F
3 . 2 e p...

9
Accessing The Menu
To access the menu enter a valid code and press the ent key. If there are any outstanding
system faults, these will be displayed first. Where there is more than one fault a > symbol
will be displayed and the scroll keys can be used to view them. Pressing the ent key again
takes the display into the menu. The Full Menu or Quick Menu is accessed, depending on the
user type.
Note: 1.  If  the user does not have group choice, all groups assigned to the user code must
     be unset.
2....

10
Omit Zones (User Type 2.3 and Above)
Purpose
This option allows the user to omit zones before setting the system.
Zones must be eligible for omission otherwise they will not be displayed.
Note: Zones remain omitted for one set period only.
Selecting Omit Zones
Enter the QUICK MENU. The 0=OMIT ZONES option is displayed.
Press the ent key to select this option.
Viewing Eligible Zones
When the Omit Zones option is selected the first zone eligible for
omission is displayed. The eligible zones can be...

11 Atm 1/2/3/4 Zones
ATM zones are omitted by entering one of the ten ATM codes (last 10
users). To select this option enter an ATM code followed by the ent
key. Use the A> key to scroll through the four ATM zone options
(ATM1 to ATM4) and select by pressing the ent key. A preprogrammed
ATM delay time will expire before omitting all ATM zones with the
selected ATM zone type. The zones will be omitted for the duration of
the ATM time-out period and the remaining time in minutes will be
displayed on the...

12
Chime (User Type 2.3 and Above)
Purpose
The Chime mode is switched on and off by this option. When the
Chime mode is on, any zones that have been programmed by the
engineer for chime will activate momentarily when opened.
Note:Your system may not require any zones of this type.
Selecting Chime
Enter the QUICK MENU. Press key 2 followed by the ent  key. The
display shows the ON/OFF status of the Chime mode. Press the >A
key to toggle between the states and press the ent key to accept the
selection....