Honeywell control panel LYNXRI User Manual

							– 41 – 
FIRE ALARM SYSTE
FIRE ALARM SYSTEFIRE ALARM SYSTE FIRE ALARM SYSTEM
MM M 
    
National Fire Protection Association’s 
Smoke Detector Recommendations 
 
U
UU U
L
LL L 
    
 LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N 
LYNXRCHKIT-HC) is installed. 
 
With regard to the number and placement of smoke and heat detectors, we subscribe to the 
recommendations contained in the National Fire Protection Associations (NFPA) Standard #72 noted 
below. 
Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms 
and areas of the household. The equipment should be installed as follows: A smoke detector installed 
outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each 
additional story of the family living unit, including basements and excluding crawl spaces and 
unfinished attics.  
In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining 
room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and 
attached garages. 
 
DININGKITCHENBEDROOM BEDROOM
.
Smoke Detectors for Minimum Protection
Smoke Detectors for Additional Protection
Heat-Activated Detectors
BEDROOM BEDROOM
BEDROOMBEDROOM
LIVING
ROOMTV ROOM
DINING
LIVING ROOM
LIVING ROOM
BASEMENT
BEDROOM BEDROOMBEDROOM
CLOSED
DOORGARAGEKTCHN
KITCHEN
TO
BEDROOM
01000-002-V0  
						

							– 42 – 
FIRE ALARM SYSTEM 
FIRE ALARM SYSTEM FIRE ALARM SYSTEM  FIRE ALARM SYSTEM  
    
Emergency Evacuation  
U
UU U
L
LL L 
    
 LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N 
LYNXRCHKIT-HC) is installed. 
 
Establish and regularly practice a plan of escape in the event of fire. The following steps are 
recommended by the National Fire Protection Association: 
 
 
1.  Position your detector or your interior and/or exterior sounders 
so that they can be heard by all occupants. 
2.  Determine two means of escape from each room. One path of 
escape should lead to the door that permits normal exit from 
the building. The other should be an alternative escape, such 
as a window, should your path to that door be unpassable. 
Station an escape ladder at such windows if there is a long 
drop to the ground. 
3.  Sketch a floor plan of the building. Show windows, doors, stairs 
and rooftops that can be used to escape. Indicate escape routes 
for each room. Keep these routes free from obstruction and post 
copies of the escape routes in every room. 
4.  Assure that all bedroom doors are shut while you are asleep. 
This will prevent deadly smoke from entering while you escape. 
5.  Try the door. If the door is hot, check your alternate escape 
route. If the door is cool, open it cautiously. Be prepared to 
slam the door if smoke or heat rushes in. 
6.  When smoke is present, crawl on the ground. Do not walk 
upright, since smoke rises and may overcome you. Clearer air 
is near the floor. 
7.  Escape quickly; dont panic. 
8.  Establish a place outdoors, away from your house, where 
everyone can meet and then take steps to contact the 
authorities and account for those missing. Choose someone to 
assure that nobody returns to the house — many die going 
back. 
  
 
2nd FLOOR
BACK
FRONT
01000-023-V0
BATH CLOSET
BEDROOM
BEDROOM
BEDROOM
1st FLOOR
BATH KITCHEN
BEDROOMBEDROOM
PORCH
BACK DOOR
 
  
						

							– 43 – 
SYSTEM FUN
SYSTEM FUNSYSTEM FUN SYSTEM FUNCTIONS
CTIONSCTIONS CTIONS 
    
Security Codes 
General Information 
For additional security you (the Master User Code) can assign secondary user codes to individual users 
enabling them to perform specific system functions. These secondary users are identified by user 
numbers when their codes are assigned. You can assign up to 6 user codes (2-digit user numbers 03-
08). Note that the master user is the only one who can assign codes to secondary users, and is 
designated user no. 02; user no. 01 is the Installer’s code. 
All codes can be used interchangeably when performing system functions (a system armed with one 
users code can be disarmed by another users code), with the exception of the Babysitter Code described 
below. 
Babysitter Code (User 07):  This code can be used to arm the system, but cannot disarm the system 
unless the system was armed with this code. This code is typically assigned to someone (such as a 
babysitter) who needs to arm/disarm the system only at certain times. The Babysitter Code is assigned 
to User 07.  
Duress Code (User 08):  This feature is intended for use when you are forced to disarm or arm the 
system under threat. When used, the system will act normally, but can silently notify the alarm 
monitoring company of your situation, if that service has been provided. Duress Code is assigned to 
User 08. 
The Duress Code is useful only when the system is connected to an alarm monitoring 
company. 
To Add/Delete a User or Change a Users Code  
Changing the Master User Code 
Follow the procedure for changing a users code, but enter User No. 02 and enter the new code twice. 
IMPORTANT: Temporary users of the system (e.g., babysitters, cleaning staff) should not be shown 
how to use any system function they do not need to know, such as bypassing protection zones for 
example. 
Sequential key depressions for all steps in a procedure must be made within 2 seconds of one another, 
or else the entire entry is aborted and must be repeated from its beginning. 
 
Add a user code:  
                        +  CODE Key + user number (03-08) + user’s code    
  Master user code 
Delete a user code:                         +  CODE Key + user number  (03-08) 
  Master user code
 
 
Wait (about 3 seconds) until the keypad beeps once before pressing any other key. The code is 
automatically deleted.   
						

							– 44 – 
SYSTEM FUNCTIONS 
Testing the System (to be conducted weekly) 
 
Entering Test Mode 
The TEST key puts your system into the Test mode, which allows each protection point to be checked 
for proper operation. The keypad sounds a single beep every 45 seconds as a reminder that the system 
is in the Test mode.  
 
NOTE:  An alarm message will not be sent to your alarm monitoring company during the following tests. 
 
Disarm the system and close all protected windows, doors, etc. The “READY” indicator should be lit. 
 
Enter: 
                       + TEST key 
  Your user code 
 
WATCH. All LCD segments will light for 3 seconds. 
 
LISTEN. The external sounder should sound for 2 seconds and then turn off. If the sounder does not 
sound, notify your service company.  
 
FAULT ZONES. Open each protected door and window in turn and listen for three beeps from the 
keypad, followed by the zone’s Voice Descriptor, if it is programmed. Identification of each faulted 
protection point should appear on the display. The display will clear when the door or window is closed. 
Walk in front of any interior motion detectors (if used) and listen for three beeps and/or voice 
descriptors, if programmed. The identification of the detector should appear on the display when it is 
activated, and its voice descriptor will be announced (if programmed). The display will clear when no 
motion is detected. Note that if wireless motion detectors are used, there is a 3-minute delay between 
activations. This is to conserve battery life. 
To test all smoke detectors, follow the manufacturers instructions. The identification of each detector 
should appear on the display when each is activated. 
If a problem is experienced with any protection point (no confirming sounds, no display), notify your 
service company. 
When all protection points have been checked and are intact (closed), there should be no zone 
identification numbers displayed on the keypad.  
 
Exit Test Mode 
When testing is completed, exit the TEST mode by entering:                        +OFF key.  
  Your user code 
 
NOTES:  (1)  If the Test mode is inadvertently left active, it automatically turns off after 4 hours.  
  (2)  Macros cannot be run from the Test mode.
  
						

							– 45 – 
SYSTEM FUNCTIONS
SYSTEM FUNCTIONSSYSTEM FUNCTIONS SYSTEM FUNCTIONS 
    
Trouble Messages 
Typical Trouble Condition Displays 
To silence the beeping sound for fault conditions, press any key.  FAULT  Indicates that a problem exists with the zone(s) displayed, accompanied by rapid beeping. 
First, determine if the zone(s) displayed are intact and make them so if they are not. If 
the zone uses a wireless detector, check that changes in the room (moving furniture, 
televisions, etc.) are not blocking wireless signals from the detector. If the problem has 
been corrected, the zone descriptor(s) and FAULT should disappear from the display. If 
not, key an OFF sequence (security code plus OFF) to clear the display. A fault condition 
can also indicate a wiring problem. If the “FAULT” display persists, notify your service 
company. Note that the system will not allow arming if a fault condition exists. To arm 
the system with a fault condition present, you must first bypass the zone(s) having the 
fault condition. 
FAULT 103  Indicates an ECP communications/supervision failure, case tamper or low battery. 
FC  Indicates that a failure has occurred in the telephone communication portion of your 
system or a problem with the phone line existed when dialing was attempted.†
  
CC Indicates that the control is on-line with the central stations remote computer. The 
control will not operate while on-line. Wait a few minutes. The display should disappear. 
dI  If this remains displayed for more than 1 minute, the system is disabled.†
  
bF  Indicates backup LRR/GSM/IP module communication failure (displayed on RF 
Keypad only) 
CA  Indicates a cancelled alarm. See Entry/Exit Delay section 
EA  Indicates an exit alarm. See Entry/Exit Delay section. 
90  Indicates that the system has detected an RF jam condition or excessive interference. If 
the condition persists, notify your service company. 
LOW BAT  Accompanied by a once-per 45 seconds beeping at the keypad, indicates a low system 
(no zone no.)  battery condition exists. Refer to the Changing the LYNXR-I System Battery section.†
  
LOW BAT  Accompanied by a once-per-45 seconds beeping at the keypad, indicates a low battery 
(with zone no.) condition exists in the wireless transmitter displayed.†
  
LOW BAT  Accompanied by a once-per-45 seconds beeping at the keypad, indicates a low battery 
(with zone 00)  condition exists in a wireless keypad.†
   † Notify your service company.  
Routine Care 
  Treat the components of your security system as you would any other electrical equipment. Do not 
slam sensor-protected doors or windows. 
  Keep dust from accumulating on the keypad and all protective sensors, particularly on motion 
sensors and smoke detectors. 
  The keypad and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or 
any other fluid on the units.  
						

							– 46 – 
SYSTEM FUNCTIONS
SYSTEM FUNCTIONSSYSTEM FUNCTIONS SYSTEM FUNCTIONS 
    
Maintaining your system 
 
The components of your security system are designed to be as maintenance-free as possible. To make 
sure that your system is in working condition, do the following: 
1.  Test your system weekly. 
2.  Test your system after any alarm occurs (see the TESTING THE SYSTEM section). 
 
Low Battery Conditions in Wireless Sensors 
Each wireless sensor in your system has a 9-volt or 3-volt battery. The system detects low battery 
conditions in wireless sensors, including smoke detectors, personal emergency transmitter, and the 
portable wireless keypad, and displays a “LOW BAT” message on the master keypad, which also beeps. 
A low battery in a wireless keypad is detected as soon as one of its keys is pressed, and the master 
keypad (e.g. Ademco 5827) will display “00”. In addition, a wireless smoke detector with a low battery 
also emits a chirp sound approximately once every 20–30 seconds, identifying itself as the smoke 
detector with the weak battery. 
NOTE:  A low battery message means that battery replacement in the indicated sensor(s) is due within 30 days. 
In the meantime, a sensor with a low battery is still operational. 
To silence Low Battery Warning Tones at the Keypad: Press the OFF key. 
The low battery message display will remain on as a reminder. When you replace the weak battery 
with a fresh one, the sensor will send a good battery signal to the control when the sensor is activated 
(opening/closing of door, window, etc.).  
To clear the “LOW BAT” message enter: 
                       +  OFF key.  
  Your user code 
 
When replacing batteries, use only those recommended by your installer. 
Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2–4 years of 
service. 3-volt lithium batteries may provide from 4-7 years of operation. Actual battery life will depend on the 
environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and 
the specific type of sensor. Factors such as humidity, high or low temperatures, and large swings in temperature may all 
lead to the reduction of actual battery life in an installation.  
Changing the LYNXR-I System Battery 
In the event of an AC power loss, the LYNXR-I is powered by a rechargeable, nickel-metal hydride 
battery pack. The battery pack should be replaced when a “LOW BAT” message with no zone number is 
displayed. 
 NOTE:  The battery pack (P/N LYNXRCHKIT-SC or LYNXRCHKIT-HC) should be changed every four 
years and must be replaced by a qualified service technician.  
 Following battery pack replacement, rechargeable batteries may take up to 48 hours to charge. The 
“LOW BAT” message may be displayed after one minute, however it should clear within 4 hours or by 
entering Test Mode.  
						

							– 47 – 
Summary Of Audible Notification
Summary Of Audible NotificationSummary Of Audible Notification Summary Of Audible Notification 
    
 
*UPPER CASE indicates announcements after pressing STATUS once. Lower case indicates announcements after 
pressing STATUS twice. 
SOUND CAUSE  DISPLAY  ANNOUNCEMENT* 
INTERRUPTED 
Speaker and 
external piezo and 
bell FIRE ALARM FIRE ALARM is displayed; zone 
number in alarm displayed. fire alarm + zone voice 
descriptor 
(Voice descriptor is 
interlaced with the siren and 
sounds every 45 seconds) 
CONTINUOUS 
Speaker and 
external piezo and 
bell BURGLARY/AUDIBLE 
EMERGENCY ALARM  ALARM  is displayed; zone number 
in alarm displayed. alarm + zone voice 
descriptor 
(Voice descriptor is 
interlaced with the siren and 
sounds every 45 seconds) 
ONE SHORT BEEP 
(not repeated)  
Speaker and 
external piezo a.  SYSTEM DISARM   
b. SYSTEM ARMING  
ATTEMPT WITH AN 
OPEN ZONE. 
c.  BYPASS VERIFY  a. Green LED on steady  
b. The number of the open protection 
zone is displayed after pressing 
STATUS. 
c. Numbers of the bypassed 
protection zones are displayed 
(One beep is heard for each zone 
displayed).  a. DISARMED–READY  TO 
ARM 
b. DISARMED–NOT  READY 
TO ARM 
c. zones bypassed 
ONE SHORT BEEP 
(once every 45 
secs) Speaker and 
external piezo a.  SYSTEM IS IN TEST 
MODE 
b. LOW BATTERY AT A 
TRANSMITTER 
c. SYSTEM LOW 
BATTERY 
d. FAIL TO 
COMMUNICATE a. Opened zone identifications will 
appear. 
b. LOW BAT displayed with zone 
number of transmitter. 
c. LOW BAT displayed with no zone 
no. 
d. FC displayed with no zone no. a. No  announcement 
 
b. low battery + zone voice 
descriptor 
c. system low battery 
 
d. check  system 
TWO SHORT 
BEEPS  
Speaker and ext. 
piezo ARM AWAY OR MAXIMUM    AWAY or AWAY + INSTANT is 
displayed. Red ARMED indicator is 
lit. ARMED AWAY [INSTANT] – 
EXIT NOW 
THREE SHORT 
BEEPS 
Speaker and 
external piezo a.  ARM STAY OR INSTANT  
 
b. ZONE OPENED WHILE 
SYSTEM IS IN CHIME 
MODE.   a. STAY or STAY + INSTANT is 
displayed. Red ARMED indicator is 
lit. 
b. CHIME displayed, number of open 
protection zone will be displayed if 
the Status key is pressed. a. ARMED STAY [INSTANT] 
– EXIT NOW 
 
b. zone voice descriptor 
RAPID BEEPING  
Speaker and 
external piezo a.  TROUBLE   
 
b. MEMORY OF ALARM  a. FAULT displayed.  Number of 
troubled protection zone is 
displayed. 
b. FIRE ALARM or ALARM is 
displayed; zone number in alarm is 
displayed.  a. fault + zone voice 
descriptor 
 
b. fire alarm or alarm + zone 
voice descriptor 
SLOW BEEPING  
Speaker and 
external piezo a. ENTRY DELAY 
WARNING 
 
b. EXIT DELAY WARNING  
  a. Exceeding the delay time without 
disarming causes alarm.  
b. AWAY or AWAY + INSTANT  is 
displayed a. DISARM SYSTEM NOW 
 
b. ARMED  [AWAY] 
[INSTANT] – EXIT NOW 
  
						

							– 48 – 
Summary Of Audible Notification
Summary Of Audible NotificationSummary Of Audible Notification Summary Of Audible Notification 
    
 
Additional Announcements: 
Pressing STATUS key once will announce the following primary messages, depending on 
the system’s status at the time: 
Disarmed–Ready to Arm [check system] 
Disarmed [not ready to arm] 
Armed [away] [stay] [instant] [check system] [exit now] 
 
Pressing the STATUS key twice will announce the following secondary messages, depending 
on the system’s status at the time: 
Fire Alarm + zone voice descriptor Fault + zone voice descriptor Zones Bypassed 
Alarm + zone voice descriptor Low Battery + zone voice descriptor System Low Battery 
Fire Fault + zone voice descriptor  Chime AC Loss 
 
NOTE: If there are no secondary messages, the primary status messages will be announced. 
 LED Meanings 
ARMED LED: ON = System armed 
(Red)  OFF = System disarmed 
  Blinking = System armed, but a fault exists or once per second when AVM (VOX or Talk) or 
speaker phone mode is active. 
 
READY LED: ON = System disarmed, ready to arm 
(Green)  Blinking = System disarmed, not ready to arm (a fault exists) or once per second when AVM (VOX 
or Talk) or speakerphone mode is active. 
 
NOTE: When the system is armed, the READY LED turns off.  
						

							– 49 – 
UL NOTICE: This is a Grade A residential system. 
  
FCC STATEMENT 
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING 
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS 
DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY 
CAUSE UNDESIRED OPERATION.  
Federal Communications Commission (FCC) Part 15 Statement 
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC 
requires the following statement for your information: 
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, 
in strict accordance with the manufacturers instructions, may cause interference to radio and television 
reception. It has been type tested and found to comply with the limits for a Class B computing device in 
accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable 
protection against such interference in a residential installation. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is encouraged 
to try to correct the interference by one or more of the following measures: 
•  If using an indoor antenna, have a quality outdoor antenna installed. 
•  Reorient the receiving antenna until interference is reduced or eliminated.  
•  Move the radio or television receiver away from the receiver/control. 
•  Move the antenna leads away from any wire runs to the receiver/control. 
•  Plug the receiver/control into a different outlet so that it and the radio or television receiver are on 
different branch circuits. 
 
If necessary, the user should consult the dealer or an experienced radio/television technician for additional 
suggestions. The user or installer may find the following booklet prepared by the Federal Communications 
Commission helpful: Interference Handbook. This booklet is available from the U.S. Government Printing 
Office, Washington, DC 20402. 
The user shall not make any changes or modifications to the equipment unless authorized by the 
Installation Instructions or Users Manual.  Unauthorized changes or modifications could void the users 
authority to operate the equipment. 
 
Industry Canada 
This Class B digital apparatus complies with Canadian ICES-003. 
Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
						

							– 50 – 
 
Federal Communications Commission (FCC)  Part 68 
This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA.  On the 
front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence 
Number (REN).  You must provide this information to the telephone company when requested. 
This equipment uses the following USOC jack: RJ31X 
This equipment may not be used on telephone-company-provided coin service.  Connection to party lines 
is subject to state tariffs.  This equipment is hearing-aid compatible. 
 
Industry Canada 
NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the 
equipment meets telecommunications network protective, operational and safety requirements as 
prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department 
does not guarantee the equipment will operate to the user’s satisfaction. 
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities 
of the local telecommunications company. The equipment must also be installed using an acceptable 
method of connection. The customer should be aware that compliance with the above conditions may not 
prevent degradation of service in some situations. 
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any 
repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the 
telecommunications company to request the user to disconnect the equipment. 
Users should ensure for their own protection that the electrical ground connections of the power utility, 
telephone lines and internal metallic water pipe system, if present, are connected together, This precaution 
may be particularly important in rural areas. 
Caution: Users should not attempt to make such connections themselves but should contact appropriate 
electric inspection authority, or electrician, as appropriate. 
Ringer Equivalence Number Notice: 
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the 
maximum number of terminals allowed to be connected to a telephone interface.  The termination on an 
interface may consist of any combination of devices subject only to the requirement that the sum of the 
Ringer Equivalence Numbers of all the devices does not exceed 5.