Home > Honeywell > Control panel > Honeywell control panel LYNXR2 User Manual

Honeywell control panel LYNXR2 User Manual

Here you can view all the pages of manual Honeywell control panel LYNXR2 User Manual. The Honeywell manuals for Control panel are available online for free. You can easily download all the documents as PDF.

Page 11

– 11 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
About the Master Keypad 
 
General  
IMPORTANT: If the keypad beeps rapidly upon entering the premises, an alarm has occurred during 
your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT 
THE POLICE from a nearby safe location.  
 
The keypad allows you to control all system functions. In the speaker phone mode the keypad becomes 
a full-function telephone keypad. The keypad features...

Page 12

– 12 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
Master Keypad Definitions   
BYPASS
NO DELAY RECORD
TEST
FUNCTION STATUSVOLUMEPLAY
CODE LIGHTS ON
LIGHTS OFF
CHIME ESCAPE
ADD
DELETE
SELECT
ARMED
READY
132
4
6
8
9
101215
16
17
19
18
1409015-003-V0
3
65
5
98
7
AUX0
13
74STAY
OFF
AWAY1
2021
2
11 
 
 
IMPORTANT! 
When you use the keypad to enter codes and commands, press the keys within 2 seconds of one another. If 2 
seconds elapse without a key depression, the entry is aborted...

Page 13

– 13 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
Master Keypad Definitions 
 
5. TEST
  KEY: Tests the system and alarm 
sounder.  
6. BYPASS
  KEY: Removes individual protection 
zones from being monitored by the system. 
Displays currently bypassed zones.  
Used to adjust volume of voice messages. 
7. CODE
  KEY:  Allows entry of additional user 
codes that can be given to other system users. 
8. CHIME
  KEY:  Turns the Chime mode on and 
off. When on, any entry through a...

Page 14

– 14 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
About the Display and Indicators 
 
Display Definitions (for other displays, see Trouble Messages) ALARM
AWAYINSTANTSTAYFIREREC MESSAGEBYPASSFAULT
CHIME   TEST  LOW BAT  AC
 ALARM:   Appears when the system is armed and an intrusion has been detected (also appears 
during a fire alarm or audible emergency alarm). Accompanied by the protection zone 
that is in alarm. 
AWAY:  All burglary zones, interior and perimeter, are armed....

Page 15

– 15 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Checking System Status 
General Information 
Before arming your system, all protected doors, windows, and other protection zones must be closed or 
bypassed (see the BYPASSING PROTECTION section). Pressing the 
STATUS key will announce all 
zones that are faulted, as well as any other abnormal system condition, making it easier for you to 
secure any open zones. 
READY LIGHT:  The green READY indicator on...

Page 16

– 16 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Arming the System  
Arming in Stay Mode 
Use this mode when you are staying home, but expect someone to use the entrance door later.  Close all 
protected perimeter windows and doors before arming.  The green READY indicator on the keypad 
should be lit if the system is ready to be armed. 
To arm in STAY mode: 
                       + STAY  or press and hold 
STAY **
 
  Your User code** 
** See Quick...

Page 17

– 17 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Arming the System  
Auto Stay Feature 
If this feature is enabled by installer, the LYNXR-2SIA, when armed AWAY from the control’s keypad 
or a Wireless Keypad, switches to the STAY mode if the Exit Time expires and no exit has been made.   NOTE:   If the exit route entry/exit sensor is in a check condition or has been bypassed it will result in a loss of interior protection because the alarm system will...

Page 18

– 18 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Entry/Exit Delays  
Exit Delay 
Exit delay begins immediately after arming the system, and gives you time to leave through the 
designated exit door without setting off an alarm.  A slow beeping will sound throughout the exit delay 
period, if programmed. During the last 10 seconds of the exit delay fast beeps will sound as a warning 
that the delay time is nearing its end. The exit beeps cannot be...

Page 19

– 19 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Disarming the System 
 
NOTE:  The control will provide a long confirmation ding when it is disarmed using an RF Key Fob.  
Use the 
OFF key to disarm the system and to silence alarm and trouble sounds. See the SUMMARY 
OF AUDIBLE NOTIFICATION section for information, which will help you to distinguish between fire 
and burglary alarm sounds. 
 
**IMPORTANT** 
If you return and the main burglary sounder...

Page 20

– 20 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Bypassing Protection Zones 
 
Bypassing Individual Zones 
Use the BYPASS key when you want to arm your system with one or more zones intentionally 
unprotected. Bypassed zones are unprotected and will not cause an alarm when violated while your 
system is armed. All bypasses are removed when an OFF sequence (security code plus OFF) is 
performed. Bypasses are also removed if the arming procedure that...
Start reading Honeywell control panel LYNXR2 User Manual

Related Manuals for Honeywell control panel LYNXR2 User Manual

All Honeywell manuals