Home > Honeywell > Control panel > Honeywell control panel LYNX Touch User Manual

Honeywell control panel LYNX Touch User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Honeywell control panel LYNX Touch User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							– 61  – 
    FIRE
    FIREFIRE FIRE/CO /CO/CO
    /CO ALARM SYSTEM ALARM SYSTEM ALARM SYSTEM
     ALARM SYSTEM 
      
     
    National Fire Protection Association’s 
    Smoke Detector Recommendations 
     
    UL
    ULUL
    UL 
        LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour 
    backup battery (P/N LYNXRCHKIT-SHA) is installed.
     
     
    With regard to the number and placement of smoke and heat detectors, we subscribe to the 
    recommendations contained in the National Fire Protection Associations (NFPA) Standard 
    #72 noted below.  
    Early warning fire detection is best achieved by the installation of fire detection equipment 
    in all rooms and areas of the household. The equipment should be installed as follows: A 
    smoke detector installed outside of each separate sleeping area, in the immediate vicinity of 
    the bedrooms and on each additional story of the family living unit, including basements and 
    excluding crawl spaces and unfinished attics.  
    In addition, the NFPA recommends that you install heat or smoke detectors in the living 
    room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage 
    rooms, basements and attached garages. 
     
    DINING KITCHENBEDROOM
    BEDROOM
    BEDROOM
    BEDROOM
    LIVING ROOMBEDROOM BDRM
    DINING 
    LIVING ROOM
    TV ROOM
    KITCHEN
    BEDROOM
    BEDROOM
    TO
    BR
    LVNG RM
    BASEMENT KTCHN.CLOSED
    DOOR
    GARAGE
    Smoke Detectors for Minimum Protection
    Smoke Detectors for Additional Protection
    Heat-Activated Detectors
    BDRM
    floor_plan-001-V1  
    						
    							– 62  – 
    FIRE
    FIREFIRE FIRE/CO /CO/CO
    /CO ALARM SYSTEM  ALARM SYSTEM  ALARM SYSTEM 
     ALARM SYSTEM  
      
     
    Emergency Evacuation  
    UL
    ULUL
    UL 
        LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour 
    backup battery (P/N LYNXRCHKIT-SHA) is installed.
     
    Establish and regularly practice a plan of escape in the event of fire. The following steps are 
    recommended by the National Fire Protection Association: 
    1.  Position your detector or your interior and/or exterior  sounders so that they can be heard by all occupants. 
    2.  Determine two means of escape from each room. One  path of escape should lead to the door that permits 
    normal exit from the building. The other should be an 
    alternative escape, such as a window, should your path 
    to that door be unpassable. Station an escape ladder at 
    such windows if there is a long drop to the ground. 
    3.  Sketch a floor plan of the building. Show windows, doors,  stairs and rooftops that can be used to escape. Indicate 
    escape routes for each room. Keep these routes free from 
    obstruction and post copies of the escape routes in every 
    room. 
    4.  Assure that all bedroom doors are shut while you are  asleep. This will prevent deadly smoke from entering 
    while you escape. 
    5.  Try the door. If the door is hot, check your alternate  escape route. If the door is cool, open it cautiously. Be 
    prepared to slam the door if smoke or heat rushes in. 
    6.  When smoke is present, crawl on the ground. Do not  walk upright, since smoke rises and may overcome you. 
    Clearer air is near the floor. 
    7.  Escape quickly; dont panic. 
    8.  Establish a place outdoors, away from your house, where  everyone can meet and then take steps to contact the 
    authorities and account for those missing. Choose 
    someone to assure that nobody returns to the house  — 
    many die going back. 
       
     
    
    FRONT
    
    BACK
    
    BATH
    BEDROOMKITCHEN
    BACK DOOR
    1   FLOORST
    BEDROOM
    2    FLOORND
    BATHBEDROOMPORCH
    CLOSET
    BEDROOM
    BEDR
    emerevac 
    						
    							– 63  – 
    SYSTEM FUNCTIONS 
    Testing the System (to be conducted weekly)  
    Test Mode 
    The Test mode allows each protection point to be checked for proper operation. When the 
    Walk Test mode is active, the control sounds a single beep every 30 seconds as a reminder 
    that the system is in the Test mode.  
     NOTE:  An alarm message will not be sent to your alarm monitoring company during these tests.  
    Entering Test Mode 
    Disarm the system and close all protected windows, doors, etc. The  “READY ” indicator 
    should be lit. 
     
    Testing the System 
    Arm Away
    Ready To Arm
    Arm Stay
    Back
    DelaySettings
    10:18 AM  June 8,  20105000-100-007-V0
    Tools
      1. With the system in the disarmed state, 
    select the “ Tools” icon from the second page 
    of the Home Screen. The system displays 
    the Keypad screen. 
     
    Ready To Arm
    Program the system
    Enter Code:
    Cancel
    5000-100-009-V0
    23
    1
    5 6
    4
    0 8 9
    7
    Clear
      2.  Enter your 4-digit Master User Code. The 
    system displays the Master User 
    programming screen. 
     
    Slide ShowDate Time
    Ready To Arm
    Events
    BackReminders
    TestSchedulesDevicesUsers
    5000-100-070-V0 3. Select the 
    “Test ” icon. The system displays 
    the Test screen.  
      
    						
    							– 64  – 
    SYSTEM FUNCTIONS 
    Testing the System (to be conducted weekly) 
     Ready To Arm
    Back5000-100-076-V0
    Version Number: CA01.00EXX
    CRC Number: 0X877D
    RF Version Number: 0.44
    Walk TestDialer Test
      4. Select the 
    “Walk Test ” or  “Dialer Test ” icon. 
    If Walk Test is selected proceed to Step 5. If 
    Dialer Test is selected proceed to Step 6 
    5.  “Walk Test …” is displayed on the system 
    status bar. Fault each zone as described 
    below. 
    6.  If the dialer test is unsuccessful the system  will display a Reporter Failure message. 
    Contact your security service provider. 
    Walk Test 
    FAULT ZONES.  Open each protected door and window in turn and listen for three beeps 
    from the control, followed by the zone ’s Voice Descriptor, if it is programmed. Identification 
    of each faulted protection point should appear on the display. The display will clear when the 
    door or window is closed. 
    Walk in front of any interior motion detectors (if used) and listen for three beeps and/or voice 
    descriptors, if programmed. The identification of the detector should appear on the display 
    when it is activated, and its voice descriptor will be announced (if programmed). The display 
    will clear when no motion is detected. Note that if wireless motion detectors are used, in 
    order to conserve battery life, there is a 3-minute delay between activations. 
    To test all smoke detectors, follow the manufacturers instructions. The identification of each 
    detector should appear on the display when each is activated. 
    If a problem is experienced with any protection point (no confirming sounds, no display), 
    notify your service company. 
    When all protection points have been checked and are intact (closed), there should be no zone 
    identification numbers displayed on the touchscreen.  
     
    Exiting Test Mode  
    When testing is completed, exit the Walk Test or Dialer Test mode by entering an Off 
    sequence.  
     
    NOTE:  If the Walk Test mode is inadvertently left active, it automatically turns off after 4 hours. The Dialer 
    Test mode will remain active until exited via an Off sequence. 
     
    LYNX Touch SIA Exit/Entry Delay Times 
    The LYNX Touch SIA will send an event code to the Central Station after entering and after 
    exiting from Test mode.  
    						
    							– 65  – 
    SYSTEM FUNCTIONS 
    Maintaining your system 
    The components of your security system are designed to be as maintenance-free as possible. 
    To make sure that your system is in working condition, do the following: 
    1.  Test your system weekly. 
    2.  Test your system after any alarm occurs (see the  TESTING THE SYSTEM section). 
    Routine Care 
     Treat the components of your security  system as you would any other electrical 
    equipment. Do not slam sensor-protected doors or windows. 
       Keep dust from accumulating on the touchscreen and all protective sensors, particularly 
    on motion sensors and smoke detectors. 
       The touchscreen and sensors should be cleaned carefully with a dry soft cloth.  Do not 
    spray water or any other fluid on the units. 
     
    Low Battery Conditions in Wireless Sensors 
    Each wireless sensor in your system has an internal battery. The system detects low battery 
    conditions in wireless sensors, including smoke detectors, personal emergency transmitter, 
    and the portable wireless keypad, and displays a  “Battery Low ” message on the touchscreen, 
    which also beeps. A low battery in a wireless keypad is detected as soon as one of its keys is 
    pressed. In addition, a wireless smoke detector with a low battery also emits a chirp sound 
    approximately once every 20 –30 seconds, identifying itself as the smoke detector with the 
    weak battery. 
    NOTE:  A low battery message means that battery replacement in the indicated sensor(s) is due within 30 
    days. In the meantime, a sensor with a low battery is still operational. 
    To silence Low Battery Warning Tones, enter an Off sequence.  The low battery message 
    display will remain on as a reminder. When you replace the weak battery with a fresh one, 
    the sensor will send a good battery signal to the control when the sensor is activated 
    (opening/closing of door, window, etc.). To clear the  “Low Battery ” message, enter an Off 
    sequence. 
     
    When replacing batteries, use only those recommended by your installer. 
    Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2 –4 
    years of service. 3-volt lithium batteries may provide from 4-7 years of operation. Actual battery life will 
    depend on the environment in which the sensor is used, the number of signals that the transmitter in the 
    sensor has had to send, and the specific type of sensor. Factors such as humidity, high or low temperatures, 
    and large swings in temperature may all lead to the reduction of actual battery life in an installation.   
    						
    							– 66  – 
    SYSTEM FUNCTIONS 
    Maintaining your system 
    Changing the LYNX Touch Series System Battery  
    In the event of an AC power loss, the LYNX Touch Series is powered by a rechargeable, 
    nickel-metal hydride battery pack. The battery pack should be replaced when a  “Battery 
    Low ” message with no zone number is displayed. 
     NOTE:   The battery pack (P/N LYNXRCHKIT-SC or LYNXRCHKIT-SHA) should be changed every four years 
    and must be replaced by a qualified service technician.  
     
    Following battery pack replacement, rechargeable batteries may take up to 48 hours to 
    charge. The  “Battery Low ” message may be displayed after one minute, however it should 
    clear within 4 hours or by entering Test Mode.  
    						
    							– 67  – 
    SUMMARY OF AUDIBLE & VISUAL NOTIFICATIONS  SOUND CAUSE  ANNOUNCEMENT* 
    INTERRUPTED 
     FIRE ALARM (3 beeps) 
    OR  
    CARBON MONOXIDE ALARM (4 beeps)
     fire alarm + zone voice descriptor 
    OR 
    Carbon monoxide alarm + zone voice descriptor 
    (Voice descriptor is interlaced with the sounder 
    and sounds every 45 seconds) 
    CONTINUOUS 
     
    BURGLARY/AUDIBLE EMERGENCY 
    ALARM   alarm + zone voice descriptor 
    (Voice descriptor is interlaced with the sounder 
    and sounds every 45 seconds) 
    ONE SHORT BEEP 
    (not repeated)  
     a.  SYSTEM DISARM   
    b. SYSTEM ARMING  ATTEMPT WITH AN 
    OPEN ZONE. 
    c.  BYPASS VERIFY   a. disarmed–ready to arm 
    b. disarmed–not ready to arm 
     
    c. zones bypassed 
    ONE SHORT BEEP 
    (once every 45 secs)  
    a.  SYSTEM IS IN TEST MODE 
    b. LOW BATTERY AT A TRANSMITTER 
    c.  SYSTEM LOW BATTERY 
    d. FAIL TO COMMUNICATE  a. no  announcement 
    b. low battery + zone voice descriptor 
    c. system low battery 
    d. check  system 
    TWO SHORT 
    BEEPS  
    ARM AWAY   armed away [instant] – exit now 
    THREE SHORT 
    BEEPS a.  ARM STAY OR INSTANT   
    b. ZONE OPENED WHILE SYSTEM IS IN 
    CHIME MODE.    a. armed stay [instant] – exit now 
    b. zone  voice  descriptor 
    RAPID BEEPING  
     
    a.  TROUBLE   
    b. MEMORY OF ALARM   a. fault + zone voice descriptor 
    b. fire alarm or alarm + zone voice descriptor 
    SLOW BEEPING  
     
    a.  ENTRY DELAY WARNING 
    b. EXIT DELAY WARNING   a. disarm system now 
    b. armed [away] [instant] – exit now 
    Additional Announcements: 
    The system will announce the following primary messages, depending on the system
    ’s status 
    at the time: 
    •  Disarmed –Ready to Arm [check system] 
    •   Disarmed [not ready to arm] 
    •   Armed [away] [stay] [instant] [check system] [exit now] 
     
    The system will announce the following secondary messages, depending on the system ’s 
    status at the time: 
    •   Fire Alarm + zone voice descriptor  
    •   Alarm + zone voice descriptor 
    •   Carbon Monoxide Alarm + zone voice descriptor 
    •   Carbon Monoxide Fault + zone voice descriptor 
    •   Fire Fault + zone voice descriptor 
    •   Fault + zone voice descriptor Alarm + zone voice descriptor  
    •   Low Battery + zone voice descriptor Fire Fault + zone voice descriptor 
    •   System Low Battery 
    •  Check System 
    •  AC Loss 
    •  Zones Bypassed 
    •  Chime 
     Note:  If there are no secondary messages, the primary status messages will be announced.  
    						
    							– 68  – 
    SUMMARY OF AUDIBLE & VISUAL NOTIFICATIONS 
     
    System Displays 
    The following icons will be displayed on the Home screen along with specific zone status 
    information (if applicable) to indicate system status. 
    DISPLAY DEFINITION   DISPLAY DEFINITION 
     AC Loss 
      Door Open 
     Alarm 
    (intrusion) 
      
    Window Open 
     Armed Away 
      Exit Active 
     
    Armed Stay  
      Fire 
     
    Battery Low  
     
    Flood 
     
    Check Zones  
     
    Glass Break 
     
    CO Alarm  
     
    Medical Alarm 
     
    Disarmed Not 
    Ready to Arm  
     
    Motion 
     
    Disarmed 
    Ready to Arm  
     
    Temperature  
     
    Reporter 
    Failure  
     
    90 RF Jam 
     
    Cover  
    Tamper
     
      
    94 Phone  
    Line Cut 
     
    Trouble  
     
    103 Comm. 
    Trouble 
         
     
        
     
      
      
    						
    							– 69  – 
    SUMMARY OF AUDIBLE & VISUAL NOTIFICATIONS 
     
    Zone Status Icons 
    The following icons may be displayed on the Zone Status screen. 
    ICON  DEFINITION 
     ICON  DEFINITION 
     
    Alarm  
     
    Trouble (red) 
     
    Fault (Yellow)  
     
    Bypass 
     
    Ready    
         
     
    LED Meanings 
    ARMED LED (Red):  ON = System armed 
      OFF = System disarmed 
      Blinking = System armed, but a fault exists or alternating with READY LED 
    when AVM (VOX or Talk) or speaker phone mode is active. 
     READY LED (Green):  ON = System disarmed, ready to arm 
      Blinking = System disarmed, not ready to arm (a fault exists) or alternating with ARMED LED when AVM (VOX or Talk) or speakerphone mode is active. 
    Note:  When the system is armed, the READY LED turns off.  
    						
    							– 70  – 
    Regulatory Agency Statements 
        
    Federal Communications Commission (FCC) Part 15 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or Use rs Manual.  Unauthorized changes or modifications could void the users authority to operate the equipment. 
    CLASS B DIGITAL DEVICE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installatio n. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not  occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  following measures: 
    • Reorient or relocate the receiving antenna. •  Increase the separation between the equipment and receiver. •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •  Consult the dealer or an experienced radio/TV technician for help. 
    This Class B digital apparatus complies with Canadian ICES-003. Cet appareil num érique de la classe B est conforme  à la norme NMB-003 du Canada. 
    Industry Canada (IC)  
    This device complies with RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may caus e undesired operation. 
    Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d interferences nuisibles. (2) Cet appareil doit accepter  toute interference reçue y compris les interferences causant une reception ind ésirable.  
    						
    All Honeywell manuals Comments (11)

    Related Manuals for Honeywell control panel LYNX Touch User Manual