Home > Honeywell > Control panel > Honeywell control panel LYNX Touch Security Systm User Manual

Honeywell control panel LYNX Touch Security Systm User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Honeywell control panel LYNX Touch Security Systm User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
     
    LYNX TOUCH SECURITY SYSTEM  
    Quick Guide to Home Automation Functions 
     
    Full Home Automation Guide Available Online: This Quick Guide describes the most frequently used features and functions of your system. For full details of all functions, please see the system’s Home Automation located online at: http://www.security.honeywell.com/hsc/products (see LYNX Touch Security System Home Automation Guide P/N 800-16091 or higher). The full version Home Automation Guide is also available from your installer upon request. 
    General Information 
    The Honeywell LYNX Touch control is a security enabled Z-Wave® device that is designed to automate devices in a home control network. The control allows you to easily add and control multiple devices with the press of a button and supports Z-Wave Network Wide Inclusion (NWI) mode. 
    Management of Z-Wave devices, which are also known as nodes or modules, includes two main operations; inclusion/exclusion and control.  This section describes how to Include (add) devices into your home control network, edit devices and Exclude (delete) devices. Automation and Z-Wave functions are accessed via the LYNX Touch Automation icon, Z-Wave Device Management and Z-Wave Advanced Tools screens. The devices can be controlled from the LYNX Touch control or a Mobile Device. Once the Z-Wave devices have been Included (added) to the network they can be controlled either manually or through “Scenes” that are programmed using your LYNX Touch control’s Automation features. 
    Check with your Installer to see which features are available with your system.  
     Automation is intended for lifestyle convenience. It should not be used for life safety or property protection. 
     
    U
    L Z-Wave automation functionality is supplementary only and has not been evaluated by UL. 
     
    Automation The Automation icon on the LYNX Touch Home Screen provides access to Z-Wave Home Automation features. (For 
    additional information regarding terms and functions refer to the Z-Wave Glossary included in LYNX Touch Security 
    System Home Automation Guide P/N 800-16091 or higher). A list of compatible Z-Wave Devices can be found in the 
    LYNX Touch Security System Home Automation Guide P/N 800-16091 or higher.  
    Z-Wave® System Basics 
    LYNX Touch Z-Wave options are displayed on two Automation Screens. The down  and up   arrows are used to scroll between the 
    two screens. Advance tools functions are displayed on the Z-Wave Device Management Screen. Refer to the full Home Automation Guide 
    P/N 800-16091 for complete information. 
    Automation Screen (Page 1) Options 
    Button Function 
     Switches  Provides access to the Switches Screen 
    68 Thermostats  Provides access to the Thermostats Screen 
     Locks 
    Provides access to the Locks Screen 
     Water Valves 
    Provides access to the Water Valves Screen 
    Garages Provides access to control Garage Door 
    operation. 
    Press To See 
    Failed devices Displayed if a device failure is detected in 
    the Z-Wave network (For additional 
    information Refer to the Failed Device 
    section of LYNX Touch Security System 
    Home Automation Guide P/N 800-16091 or 
    higher) 
     
    Automation Screen (Page 2) Options 
    Button Functions 
     Scenes Provides access to the Scenes Screen. Up 
    to 20 scenes can be programmed. 
     Schedules  Provides access to the Schedules Screen.  
     Rules  Provides access to the Rules Screen.  
      Tools Provides access to the Z-Wave Device 
    Management Screen 
     
    Garage door 
    setup Provides access to program/enroll 
    Garage Door Openers. 
    Other Devices Provides access to control Unknown or 
    Unsupported Devices using basic On/Off 
    commands  
        
     
     
     
     
     
    Z-Wave and Z-Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the United States and other countries.  
    						
    							 
    Z-Wave® System Basics (Continued)  
    Z-Wave Device Management Screen Options 
    Button Function 
    Include Devices  Enroll Z-Wave Devices/Modules 
    Exclude Devices  Delete Z-Wave Devices/Modules 
    View Failed Devices Displayed only when device failures have 
    been detected in the Z-Wave network 
    (For additional information Refer to the 
    Failed Device section of LYNX Touch 
    Security System Home Automation Guide 
    P/N 800-16091 or higher) 
    Advanced Tools Provides access to additional Z-Wave 
    options. 
     
    Z-Wave® Advanced Tools  
    Z-Wave Advanced Tools Options 
    Button Function 
    View Enrolled Devices View Z-Wave device information. 
    View Enrolled 
    Controllers View Controller Information. 
    Reset Controller Deletes all nodes and generates a new 
    random Home ID. Resetting the Controller 
    does not Exclude the individual devices. 
    Pri. Controller Shift  
    to Secondary Transfers the role of primary controller to 
    another controller (i.e.; a Z-Wave remote 
    control) and duplicates the Z-Wave 
    network. 
    Locking Door 
     Enable Arm Stay, Arm Away or Arm without 
    Auto-Stay when Z-Wave door lock is locked. 
    Causes the system to arm in the selected 
    mode, Away, Stay, or Away without Auto-
    Stay when the Z-Wave Door is Locked. 
    Learn 
     Includes the panel as secondary controller, 
    usually on a Z-Wave remote control, and 
    duplicates the Z-Wave network.  
    All Devices Off 
    OR 
    All Devices On Allows User to “manually” turn Off OR On all 
    switches that are programmed in the Z-
    Wave Network.  
     
    Including Z-Wave® Devices 
    The steps described below should be accomplished at the LYNX 
    Touch control in order to include (add) Z-Wave devices to the 
    network. For additional information regarding the inclusion of 
    specific Z-Wave Devices refer to the full Home Automation Guide 
    P/N 800-16091 or higher.  
    Step Action 
    1.  At the Home Screen select the “Automation” icon  
    2.  At the second page of the Automation Screen, select 
    “Tools”. 
    3.  At the “Device Management” screen, select “Include 
    Devices”.  The panel displays “Entering Inclusion Mode. 
    Please Wait…” 
    4.  “Ready to include device. Press the function button on 
    device” is displayed. Within one minute press the device’s 
    Function button or activate the switch, as applicable. 
    5.  If the module has been successfully enrolled, the panel 
    displays “Device Found! Please Wait” and then displays the 
    device information. 
    6.  After successfully including a device, the associated 
    information will be added to the top of the inclusion list. 
    7.  Repeat steps 4 - 6 to enroll additional Z-Wave devices. 
    8.  Once you have finished including devices, press the “Home” 
    key to return to the Home screen or select the “” button 
    to return to the previous screen. 
      
    Editing Z-Wave Device Names 
    The steps described below should be accomplished at the LYNX 
    Touch control in order to edit a Z-Wave devices name.  
    Step Action 
    1.  At the Home Screen select the “Automation” icon.  
    2.  At the Automation Screen, select the type of device to edit. 
    3.  Select the device that you wish to edit from the list. 
    4.  Select the edit button 
    5.  Enter the desired information (limited to 14 characters) on the displayed keypad and then select “Done”. The system returns to the previous screen. 
    6.  Press the “Home” key to return to the Home screen or select the “” button to return to the Automation screen.  
    Excluding Z-Wave® Devices 
    The steps described below should be accomplished at the LYNX 
    Touch control in order to Exclude (remove) a Z-Wave device from 
    the network. 
     
    Step Action 
    1.  At the Home Screen select the “Automation” icon.  
    2.  At the Automation Screen, select “Tools”. 
    3.  At the “Device Management” screen, select “Exclude 
    Devices”. 
    4.  “Entering Exclusion Mode. Please Wait…” is displayed 
    followed by “Ready to Exclude device. Press the function 
    button on the device”. Within one minute press the 
    device’s Function button or activate the switch. 
    5.  If the device has been successfully excluded, the device 
    information is shown on the excluded list.  If a device, 
    which is not known to the panel is excluded, “Unknown 
    Device Excluded” is displayed on the excluded list.   
    6.  Once you have finished excluding devices, press the 
    “Home” key to return to the Home screen or select the 
    “” button to return to the previous screen. 
     
    Controlling Z-Wave Devices 
    Z-Wave devices can be activated Manually or by using Scenes to 
    control a single or group of devices, by turning them OFF, ON, 
    ON to a preset lighting level, temperature or mode, and/or to 
    lock/unlock a door.  The LYNX Touch provides 20 Scenes that 
    can be configured to control up to 10 devices each. Scenes can 
    be activated manually or by a Schedule or Rule.  Schedules and 
    Rules are used to control Scenes via pre-set “Conditions” and 
    “Triggers”.  Up to 20 Rules may be programmed locally in the 
    LYNX Touch. An additional 20 Rules can be programmed through 
    Total Connect Service. Check with your Installer to see if these 
    features are available to you.  
    Manually Activating Z-Wave Devices 
    The steps described below should be accomplished at the LYNX 
    Touch control in order to manually activate devices. 
    Step Action 
    1.  At the Home Screen select the “Automation” icon.  
    2.  At the Automation Screen, select the type of device (i.e.; 
    Switches, Thermostats or Locks) that you wish to control. 
    3.  Select the device that you wish to control from the 
    displayed list. 
    4.  Refer to the figures below for typical examples of the 
    features that can be controlled manually for the devices. 
    5.  Press the “BACK” key to return to the previous screen.  
    6.  Press the “Home” key to return to the Home screen or 
    select the “” button to return to the Automation screen. 
    Note: The features and functions that can be controlled vary by 
    manufacturer. Refer to the User Manual that was provided with 
    the Z-Wave device to determine the specific capabilities.  
    						
    							 
    Manually Activating Z-Wave Devices (Continued) 
    5200-100-099-V0
    Press to Turn Off Den Lamp
    ON
    Ready To Arm
    Back Edit 
    Switch Control Screen 5200-100-100-V0
    Den Lamp
    ON 70%
    Ready To Arm
    Back Edit
    Press to Turn Off
     
    Dimmer Switch Control Screen 
    Ready To Arm
    5200-100-104-V0
    Unknown 001       Secured
    1       Unknown   Type: 0000    ID: 0000
    Node:2    Sigma Designs (Sigma Designs)
    Basic Off Basic On
    OFF
     
    Unsupported Device Control Screen 
    5200-100-101-V0EDITBACK
    73
    Set to
    Threshold Monitoring
    Fan ModeAUTO
    Living Room
    HEAT
    Hold
    Ready To Arm
     
    Thermostat Control Screen 5200-100-103-V0EDITBACK
    25.5C 23.0Set to
    Saving Off
    Fan ModeAUTO
    Living Room
    HEAT
    NORMAL
    Ready To Arm
     
    Thermostat Energy Savings Control 
    Screen 5200-100-102-V0EDITBACK
    84
    Cool
    Setpoint
    73
    Heat
    Setpoint
    Threshold Monitoring
    Fan ModeAUTO
    Living Room
    AUTO
    Hold
    Ready To Arm
     
    Thermostat Dual Setback Control 
    Screen 
    5200-100-098-V0
    Press to Lock Front DoorUnlocked
    Ready To Arm
    Back Edit 
    Lock Control Screen 
    Ready To Arm
    5100-100-106-V0
    Garage Door 1
    CLOSEDPress to open
    Edit BackClose inClose at 
    Garage Door Control Screen 5200-100-054-V0
    Press to Turn OffSwitch 003
    Water On
    Back Edit
    Ready To Arm
     Water Valve Control Screen  
    Programming/Editing/Deleting Scenes 
    The steps described below should be accomplished at the LYNX Touch control in order to program Scenes used to control Z-Wave 
    devices. For more detailed information regarding Scenes refer to the full Home Automation Guide P/N 800-16091 or higher. 
    Program a Scene 
    Step Action 
    1.  Select the “Automation” icon from the Home Screen. 
    2.  Select the “Scenes” icon from the second page of the 
    “Automation” screen. The Scenes screen is displayed.  
    3.  Select “Add New Scene”. The system displays a keypad 
    along with the next available Scene number. 
    4.  If desired, select clear then enter a name (limited to 13 
    characters) for the scene on the displayed keypad then 
    select “Done”. 
    5.  Select the “Add New Device” button. The system displays 
    the available Z-Wave device types. 
    6.  Select one of the following options: 
    Switches 
    Thermostats 
    Locks  
    Garages 
    Water Valves 
    Sirens 
    7.  Select the desired device type, then select the applicable 
    device from the displayed list. The device’s operational 
    screen is displayed. Select “Save” when finished. Up to 10 
    devices may be associated with a scene. 
    8.  Set the desired options. 
    9.  Select Save when complete. The system returns to the Z-
    Wave device screen. Select the “” button as required to 
    return to the Automation programming screen or the 
    Home key to return to the Home screen. 
     
    Edit or Delete a Scene 
    Step Action 
    1.  Select the “Automation” icon from the Home Screen. 
    2.  Select the “Scenes” icon from the second page of the 
    “Automation” screen. The Scenes screen is displayed. 
    3.  Select the scene you wish to edit or delete. 
    4.  Select the “Edit” or “Delete” button. 
    5.  If “Edit” was selected, the system advances to the 
    Scene. Edit as required and proceed to Step 6. If delete 
    was selected proceed to Step 7. 
    6.  Select Save when complete. The system returns to the 
    Z-Wave device screen. Select the “” button as required 
    to return to the Automation programming screen or the 
    Home key to return to the Home screen. 
    7.  The system displays a confirmation screen and then 
    returns to the previous screen. Select the “” button as 
    required to return to the Automation programming 
    screen or the Home key to return to the Home screen. 
    Manually Run a Scene 
    Step Action 
    1.  Select the “Automation” icon from the Home Screen.  
    2.  Select the “Scenes” icon from the second page of the 
    “Automation” screen. The Scenes screen is displayed.  
    3.  Select the scene you wish to run. 
    4. 
    Select the
     “”button to run the scene.
     
      
    						
    							Ê800-15983rŠ 
    800-16092  12/13  Rev A 
    2 Corporate Center Drive, Suite 100
    P.O. Box 9040, Melville, NY 11747
    Copyright © 2013 Honeywell International Inc.
    www.honeywell.com/security
       
    Programming/Editing/Deleting Schedules 
    The steps described below should be accomplished at the LYNX 
    Touch control in order to program Schedules that are used to 
    automatically perform certain functions at a scheduled time, day 
    of the week or month, as applicable. For more detailed 
    information regarding Schedules refer to the full Home 
    Automation Guide P/N 800-16091 or higher. 
    Program a Scheduled Function 
    Step Action 
    1.  Select the “Automation” icon from the Home Screen. 
    2.  Select the “Schedules” icon from the second page of the 
    “Automation” screen. The Schedules screen is displayed. 
    3.  At the Schedules screen, select “Add New”.  
    4.  Select “Name” then enter a name (limited to 13 
    characters) for the schedule on the displayed keypad 
    then select “Done”. 
    5.  Select “Frequency”, then select one of the displayed 
    options. 
    6.  Program the options based upon the Frequency selected 
    in Step 5. 
    7.  Select “Type” to scroll between the available options. 
    8.  If Auto Stay is selected, select “Start Time” and proceed 
    to Step 9. If “Rules” is selected proceed to Step 10. If 
    “Disarm Notification” is selected, proceed to Step 11. 
    9.  On the displayed keypad, select “Clear” and enter a 4-
    digit time on the displayed keypad, then select “Save”. 
    10.  Select “Rules” OR “Scenes”, as applicable, then select a 
    Rule or Scene from the displayed list. 
    11.  Select “Start Time” and “End Time” and on the displayed 
    keypad select “Clear. Enter a 4-digit Start Time and End 
    Time, as applicable, then select “Save”. 
    12. Select the “” button or press the Home key to return to 
    the Automation programming  or the Home screen. 
     Edit or Delete a Scheduled Function 
    Step Action 
    1.  At the Schedules screen, select the Schedule to edit or 
    delete. 
    2.  Select the “Edit” or “Delete button as applicable. If editing 
    the schedule, proceed to Step 3 or if deleting proceed to 
    Step 4  
    3.  When the Schedule programming screen appears, follow 
    Steps 4-11 as noted above in the Program a Scheduled 
    Function section to edit and save your changes. 
     
    4. Select the “Delete” button. At the displayed confirmation 
    screen select “Yes” to confirm the deletion.  
    5. Select the “” button or press the Home key to return to 
    the Automation programming  or the Home screen. 
     
    Programming/Editing/Deleting Rules 
    The steps described below should be accomplished at the LYNX 
    Touch control in order to program up to 20 Rules that are used 
    for Triggers, Z-Wave Scenes and Follow-Me Messages. For more 
    detailed information regarding Rules refer to the full Home 
    Automation Guide P/N 800-16091 or higher. 
    Program a Rule 
    Step Action 
    1.  Select the “Automation” icon from the Home Screen. 
    2.  Select the “Rules” icon from the second page of the 
    “Automation” screen. The Rules screen is displayed. 
    3.  At the Rules screen, select a “Rules” key. 
    4.  Select “Name” then enter a name (limited to 13 
    characters) for the Rule on the displayed keypad then 
    select “Done”. 
     
    Programming/Editing/Deleting Rules (Continued)  
    Step Action 
    5.  Select the “Type” button to toggle through the type options. 
    The available options are dependent upon what features are 
    programmed in your control. The system displays several new 
    programming fields that are dependent upon the Type that 
    was chosen.  
    6.  Select “Action” to toggle between options, which is dependent 
    on the selection made in Step 5. 
    7.  Select “Start Zone Type” OR “Zone Type Fault”. Select an 
    option from the displayed list, which is dependent upon the 
    selection made in Step 5. 
    8.  Select “Stop Zone Type” OR “Zone Type Restore. Select an 
    option from the displayed list, which is dependent on the 
    selection made in Step 5. 
    9.  Select “Start System Operation” OR “System Operation 1”. 
    Select an option from the displayed list, which is dependent on 
    the selection made in Step 5. 
    10.  Select “Stop System Operation” OR “System Operation 2”. 
    Select an option from the displayed list, which is dependent on 
    the selection made in Step 5. 
    11. Use the “” button to advance to next page, then select “Zone 
    Number Operation” to toggle between options. 
    12  Select the First, Second or Third “Start Zone” then select a 
    Zone from the displayed list. 
    13  Select the First, Second or Third “Stop Zone” then select a 
    Zone from the displayed list. 
    14.  Select “Save” when programming is complete. 
    15. Select the “” button or press the Home key to return to the 
    Automation programming or the Home screen. 
     Edit or Delete a Rule 
    Step Action 
    1.  At the Rules screen, select the Rule to edit or delete. 
    2.  Select the “Edit” or “Delete button as applicable. 
    3.  If editing the rule, follow Steps 4-15 as noted above in the 
    Program a Rule section. If deleting the rule, proceed to Step 4. 
    4. Select the “” button or press the Home key to return to the 
    Automation programming or the Home screen. 
     
    Garage Door Feature Operation  
    Step Action 
    1.  Select the “Automation” icon from the Home Screen. 
    2.  At the Automation Screen, select the Garages icon. 
    3.  Select the Garage door that you wish to control/program from 
    the displayed list. The control advances to the Garage Door 
    operation screen. 
    4.  Refer to the table below for additional operation and 
    programming information. 
     Button   Function 
    Edit Used to modify description of Garage Door 
    Close in  Used to set a specific period of time (up to 12 hours and
    59 minutes) before an open garage door closesautomatically. If programmed the time will also bedisplayed. 
    Close at Used to set a specific time that an open garage doorcloses automatically. If programmed the time will alsobe displayed. 
    Back Used to return the control to the Garage Door list. 
    Press to open Displayed when Garage Door is Closed. Select to Open 
    Garage Door. 
    Press to close Displayed when Garage Door is Open. Select to Close 
    Garage Door.    
      
    						
    All Honeywell manuals Comments (0)

    Related Manuals for Honeywell control panel LYNX Touch Security Systm User Manual