Honeywell C1 Autopilot Manual

							 15 
Motion detection
You can turn motion detection on or off, as well as adjust the sensitivity.
1 Press the side menu button on the 
home screen.
2 Press the camera you want to change 
the settings on. Look for the name you 
gave the camera when installed.
3 Press Motion Detection.
4 Use the Motion Detection switch to turn 
motion detection on or off.
5 Adjust how big a movement triggers 
a Motion Event by selecting Off, Low, 
Medium, or High.•  Off - ignores all movement.
•  Low - detects only big movement.
•  Medium - detects general movement and changes in environment.
•  High - detects all movement and changes in environment.
To set up separate zones, see “Set up detection zones” on page 20. 
						

							  16
Sound detection
You can turn sound detection on or off, as well as adjust the sensitivity.
1 Press the side menu button on the 
home screen.
2 Press the camera you want to change 
the settings on. Look for the name you 
gave the camera when installed.
3 Press Sound Detection.
4 Use the Sound Detection switch to turn 
sound detection on or off.
5 Adjust the volume of sound that 
triggers a Sound Event by selecting 
Low, Normal, or High.•  Low – detects only loud sounds, 
such as a motorcycle or food 
processor, around 80–100 decibels.
•  Normal – detects general sounds 
like a refrigerator, air conditioner 
or conversation, around 50–100 
decibels. 
•  High – detects even the quietest 
sounds like a pin drop or whispers, 
around 10–100 decibels. 
						

							 17 
Smoke or carbon monoxide alarm detection
If your smoke or carbon monoxide alarm goes off and your camera is on, it will send you 
an alert that a smoke or CO alarm has been detected.
To test this feature, press and hold the Test button on your smoke/CO detector for at least 
5 seconds or 3 cycles of the detector’s alarm. A shorter test might not trigger a sound 
event. 
						

							  18
Delete a camera
If you need to remove a camera from your 
account, it is easy to do using the app.
1 Press the side menu button on the 
home screen.
2 Press the camera you want to delete. 
Look for the name you gave the 
camera when installed.
3 Press Camera Configuration.
4 Press DELETE CAMERA.
Note: Deleting the camera from the app 
will result in losing all stored video clips 
that have not been saved to another 
device.
5 To re-install the camera, follow the steps in “Launch the Lyric app” on page 4.  
						

							 19 
Geofencing setup
If you set up the camera to use geofencing to turn itself on and off, the camera will sense 
where you are through the location of your mobile device.
Note: Turn geofencing on in the camera settings. See “Camera settings” on page 12.
1 Press the side menu button on the 
home screen.
2 Press Geofence.
3 Use the Geofence this Location switch 
to turn geofencing on or off.
4 When geofencing is on, the Location 
Status will indicate whether you are 
Home or Away.
5 Press Geofence Radius to change how 
close your smartphone is to the camera 
for it to turn on (when Away) or off 
(when Home). 
6 Press the black dot and drag the 
geofence radius to the size you want.
7 Press NEXT.
8 When the geofencing is set, press 
NEXT. 
						

							  20
Set up detection zones
Draw your own alert zones for extra sensitivity or to ignore background motion such as a 
ceiling fan.
1 Press the side menu button on the 
home screen.
2 Press the camera you want to change 
the settings on. Look for the name you 
gave the camera when installed.
3 Press Motion Detection.
Note: The app will need access to the 
camera so you can set up detection zones.
4 The default area for Zone 1 is the entire 
snapshot. To re-size, drag the rectangle 
from any corner or edge. Drag from the 
center to re-locate.
5 Set the desired sensitivity for Zone 1 by 
selecting Off, Low, Medium, or High. •  Off - no motion detection in this 
zone.
•  Low - detects only big movement.
•  Medium - detects general movement 
and changes in environment.
•  High - detects all movement and 
changes in environment. 
						

							 21 
Set up detection zones
6 Press Zone 2.
7 Press Enable this Detection Zone.
8 Re-size or re-locate Zone 2 the same 
way you did Zone 1.
Note: Zones can not overlap. 
						

							  22
App settings and account info
Follow these steps to see app settings such as version info, help, etc.
1 Press the side menu button on the 
home screen.
2 Press App Settings & Info. 
3 Select any of the menu options for 
more information.
Follow these steps to see your account 
information, such as name, email address, 
password reset, etc.
1 Press the side menu button on the 
home screen.
2 Press My Account. 
3 Change your name, email address, 
password, or access. Follow the steps in 
the app to complete. 
						

							 23 
Manage messages
Use the app to view and manage messages about motion or sound detected by your 
camera.
1 Press the side menu button on the 
home screen.
2 Press Messages. 
3 The messages are displayed.
4 Press a message to read it.
5 Press the back arrow to go back to the 
list of messages. 
						

							  24
Frequently Asked Questions
What kind of maintenance does my security camera need?
Your camera requires no maintenance.
What should I do if I get a message that the security camera is unavailable?
1. Check that the security camera is connected to power.
2.  Check for any notification from Honeywell sent via email about scheduled maintenance.
3.  Check that your home Wi-Fi network is working, and the camera LED is solid green.
4.  If the camera LED is not green, unplug the camera from wall outlet, wait 10 seconds, 
and plug it back in. If you can livestream from the camera, it is now available.
5.  There are other networks and servers involved in the data transfer process, and one of 
them could be down temporarily. Wait a bit and try again. 
6.  If none of these steps solves the problem, contact Honeywell Lyric Support at  
1-800-633-3991.
Does the security camera record continuously?
No. To conserve bandwidth, the security camera only records to the cloud when it detects 
a sound or motion. 
When does the camera record?
When the security camera detects sound or motion, it records a clip that includes 
5 seconds before the sound or motion and 25 seconds after, then uploads the 30 second 
clip to cloud storage and sends you a notification of the event. If the cloud is unavailable 
or the security camera is not connected to the internet, clips are stored on the SD card, 
and uploaded to the cloud when the connection is restored.
How many clips can be stored on the SD card?
SD card storage is synced with the numbers of clips saved to the cloud and based on the 
storage tier you selected. 
Plan 1-day storage (default) 7-day storage30-day storage
Clips stored 503501500