Honeywell 1900ghd-2 User Manual

3 - 21
To see what the factory default settings are, refer to the table of Menu Commands, beginning on page 12-4.  The standard prod-
uct default settings for each of the commands are indicated by an asterisk (*).  
Note: Scanning this bar code also causes both the scanner and the base or Access Point to perform a reset and become 
unlinked.  The scanner must be placed in the base, or the Access Point linking bar code must be scanned to re-establish 
the link.  Refer to Scanner Modes, page 3-9 for...

3 - 22
Bluetooth HID Keyboard Connect
Your scanner can be paired with Bluetooth-capable devices, such as personal computers, laptops, and tablets, so that 
scanned data appears on your device screen as though it was entered on the keyboard.  In order to pair with the Bluetooth 
device: 
1. Scan the appropriate Bluetooth HID Keyboard Connect bar code below. 
2. Set tyour personal computer, laptopt or tablet so it searches for other Bluetooth devices.  (Refer to your device’s User’s 
Guide for pairing...

3 - 23
Virtual Keyboard
Once your scanner has been connected directly to an iPad, smart phone, or laptop, you can toggle the virtual keyboard on 
your device with a quick double pull of the scanner trigger. 
Note: This feature is not supported in Granit devices.
Bluetooth HID Keyboard Disconnect
If your scanner has been connected directly to an iPad, smart phone, or laptop using Bluetooth HID Keyboard Connect 
(page 3-22), you must disconnect it in order to once again communicate with the base or Access...

3 - 24
PDAs/Mobility Systems Devices
You may also use the scanner with a PDA or a Honeywell Mobility Systems device.  Scan the bar code below and follow the 
instructions supplied with your Bluetooth device to locate the scanner, and connect with it.  
Changing the Scanner’s Bluetooth PIN Code 
Some devices require a PIN code as part of the Bluetooth security features.  Your scanner’s default PIN is 1234, which you 
may need to enter the first time you connect to your PDA or PC.  The PIN code must be...

3 - 25
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base or an 
Access Point.  During the connection setup process, the scanner transmits in order to search for and connect to a base or 
an Access Point.  In order to prevent continuous transmissions that could interfere with other users of the ISM band, the 
number of attempts to connect is limited by this setting.  After the maximum number of attempts is reached, the...

3 - 26
When the scanner goes out of range, the scanner repeatedly attempts to connect to the base unit or Access Point.  Each 
attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time.  After one hour, the scanner 
powers off and batch mode data is lost.
Maximum Link Attempts set to 15
Other values at default setting
When the scanner goes out of range, 15 attempts are made to link to the base unit or Access Point.  Each attempt consists 
of approximately 5 seconds of...

3 - 27
Example:A good read beep is required for any item on file, but a razz or error tone is required if the item is not on file.  In this 
case,
[ESC]7, is sent to the host for an on-file product
[ESC]8,[ESC]8, is sent to the host for a not-on-file product
When a bar code is scanned, the scanner enters a timeout period until either the host ACK sequence is received, or the timeout 
expires (in 10 seconds, by default).
Once Host ACK is enabled, the system works as follows when a bar code is scanned:...

3 - 28 

4 - 1
4
Input/Output Settings
Power Up Beeper
Note: This feature does not apply to the CCB02-100BT/CCB05-100BT base.
The scanner can be programmed to beep when it’s powered up.  If you are using a cordless system, the base can also be pro-
grammed to beep when it is powered up.  Scan the Off bar code(s) if you don’t want a power up beep.  Default = Power Up 
Beeper On - Scanner.
Beep on BEL Character
You may wish to force the scanner to beep upon a command sent from the host.  If you scan the Beep on BEL...

4 - 2
Trigger Click
To hear an audible click every time the scanner trigger is pressed, scan the Trigger Click On bar code below.  Scan the Tr i g g e r  
Click Off code if you don’t wish to hear the click.  (This feature has no effect on serial or automatic triggering.)  Default = Trigger 
Click Off.
Good Read and Error Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read.  Turning this option off only turns off the beeper 
response to a good read indication....