Honeywell 1900ghd-2 User Manual

 ix
Maintenance ...................................................................................................................... 14-1
Cleaning the Scanner .................................................................................................. 14-1
Cleaning the Window ................................................................................................... 14-1
Health Care Housing ......................................................................................................

 x 

1 - 1
1
Getting Started
About This Manual
This User’s Guide provides installation and programming instructions for the Xenon™ 1900 and 1910 corded area-imaging 
scanners, the Xenon 1902 and 1912 cordless area-imaging scanners, the Granit 1910i and 1980i corded industrial scanners, 
and the Granit 1911i and 1981i cordless industrial scanners.  Product specifications, dimensions, warranty, and customer sup-
port information are also included.
Honeywell bar code scanners are factory programmed for the most...

1 - 2
2. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner.  Loosen the locking plate 
and slide it over the base of the cable connector to lock the cable in place.  Tighten the screw.
Corded Granit Scanner 
USB Connection:
CCB01-010BT Base 
USB Connection: 

1 - 3
Note: The power supply must be ordered separately, if needed.
3. If you are connecting a CCB01-010BT Base, make sure the cables are secured in the wireways in the bottom of the 
cordless base and the base sits flat on a horizontal surface.  If you are connecting a CCB02-100BT or CCB05-100BT 
Base, see Mounting a CCB02-100BT/CCB05-100BT Baseon page 1-9.
4. The scanner beeps.
5. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this 
manual....

1 - 4
2. Connect the appropriate interface cable to the device and to the terminal/computer.
3. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner.  Loosen the locking plate 
and slide it over the base of the cable connector to lock the cable in place.  Tighten the screw.
Corded Xenon Scanner 
Keyboard Wedge 
Connection:
Corded Granit Scanner 
Keyboard Wedge 
Connection: 

1 - 5
Note: The power supply must be ordered separately, if needed.
4. If you are connecting a CCB01-010BT Base, make sure the cables are secured in the wireways in the bottom of the 
cordless base and the base sits flat on a horizontal surface.  If you are connecting a CCB02-100BT or CCB05-100BT 
Base, see Mounting a CCB02-100BT/CCB05-100BT Baseon page 1-9.
5. Turn the terminal/computer power back on.  The scanner beeps.
6. Verify the scanner or cordless base operation by scanning a bar code from the...

1 - 6
Connecting with RS232 Serial Port
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the scanner.
Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer.
Corded Xenon Scanner 
RS232 Serial Port 
Connection:
Corded Granit Scanner RS232 Serial 
Port Connection: 

1 - 7
3. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner.  Loosen the locking plate 
and slide it over the base of the cable connector to lock the cable in place.  Tighten the screw.
Note: The power supply must be ordered separately, if needed.
4. If you are connecting a CCB01-010BT Base, make sure the cables are secured in the wireways in the bottom of the 
cordless base and the base sits flat on a horizontal surface.  If you are connecting a CCB02-100BT or...

1 - 8
Connecting with RS485
A Xenon scanner or cordless base can be connected for an IBM POS terminal interface.  (This interface is not available in 
the Granit devices.)
1. Connect the appropriate interface cable to the device, then to the computer.
Note: The power supply must be ordered separately, if needed.
2. Make sure the cables are secured in the wireways in the bottom of the cordless base and the base sits flat on a 
horizontal surface.
3. Turn the terminal/computer power back on.  The scanner...