honda nc700 s sa sd owners 2012 User Manual

98
Troubleshooting
Other Warning Indication
Fuel Gauge Failure Indication
If the fuel system has an error, the fuel gauge 
indicators will be displayed as shown in the 
illustration.
If this occurs, see your dealer as soon as 
possible.
12 NC700S (NM-1)-32MGS600.book  98 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 

99continued
Troubleshooting
Tyre Puncture
Repairing a puncture or removing a wheel 
requires special tools and technical expertise. 
We recommend you have this type of service 
performed by your dealer.
After an emergency repair, always have the 
tyre inspected/replaced by your dealer.
Emergency Repair Using a Tyre 
Repair Kit
If your tyre has a minor puncture, you can 
make an emergency repair using a tubeless 
tyre repair kit.
Follow the instructions  provided with the 
emergency tyre repair kit....

Tyre Puncture u Removing Wheels
100
Troubleshooting
(NC700SA/SD only)
When removing and installing the wheel, be 
careful not to damage the wheel speed 
sensor and pulser ring.
❙Front Wheel
Removal
1.Park on a firm, level surface.
2.Cover both sides of  the front wheel and 
brake caliper with protective tape or 
cloth.
3.On the right side, remove the mounting 
bolts and remove the brake caliper.
u Support the brake caliper assembly so 
that it doesn’t hang from the brake 
hose. Do not twist the brake...

Tyre Puncture u Removing Wheels
101continued
Troubleshooting
4.Loosen the axle pinch bolt.
5.Support your motorcycle securely and 
raise the front wheel off the ground 
using a maintenance stand or a hoist.
6.On the left side, loosen and withdraw 
the front axle shaft, and remove the side 
collars and wheel. Installation
1.Attach the side collars to the wheel.
2.On the left side, place the wheel 
between the fork legs and insert the 
front axle shaft to the end, through the 
left fork leg and wheel hub....

Tyre Puncture u Removing Wheels
102
Troubleshooting
4.Install the brake caliper and tighten the 
mounting bolts.
u Take care to prevent the brake caliper 
from scratching the wheel during 
installation.
u Use new mounting bolts when 
installing the brake caliper.
5.Lower the front wheel on the ground.
6.(NC700S)
Apply the brake lever several times. 
Then, pump the fork several times.
(NC700SA/SD)
Apply the brake lever and brake pedal 
several times. Then, pump the fork 
several times.
7.Tighten the axle...

Tyre Puncture u Removing Wheels
103continued
Troubleshooting
❙Rear Wheel
Removal
1.Support your motorcycle securely and 
raise the rear wheel off the ground using 
a maintenance stand or a hoist.
2.(NC700SD only)
Release the parking brake.
3.(NC700SD only)
Remove the mounting bolts and remove 
the parking brake caliper. (NC700SD only)
Parking brake caliper
Mounting 
bolts
12 NC700S (NM-1)-32MGS600.book  103 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 

Tyre Puncture u Removing Wheels
104
Troubleshooting
4.Loosen the rear axle  nut, lock nuts and 
turn the adjusting nuts  so the rear wheel 
can be moved all the way forward for 
maximum drive chain slack.
5.Remove the rear axle nut.
6.Remove the drive chain from the rear 
wheel sprocket by pushing the rear wheel 
forward.
Wheel speed sensor (NC700SA/SD only)
Lock nut Rear axle 
nut
Adjusting nut Washers
Pulser ring 
(NC700SA/SD only)
Lock nut
Rear axle shaft
Adjusting nut
Washer
Drive 
chain
12 NC700S...

Tyre Puncture u Removing Wheels
105continued
Troubleshooting
7.Remove the rear axle shaft, washers, 
brake caliper bracket, rear wheel and side 
collars.
uSupport the brake cali per assembly so 
that it doesn’t hang from the brake 
hose. Do not twist the brake hose.
u Avoid getting grease, oil, or dirt on the 
disc to pad surfaces.
u Do not push the brake pedal while the 
wheel is removed.
(NC700SD only)
u Do not pull the parking brake lever 
while the wheels is removed.
Installation
1.To install the...

Tyre Puncture u Removing Wheels
106
Troubleshooting
3.Adjust the drive chain. 2P. 83
4.Install and tighten the rear axle nut.
5.Tighten the drive chain adjusting nuts 
lightly, then hold the adjusting nuts and 
tighten the lock nuts.
6.After installing the wheel, apply the brake 
pedal several times, then recheck the 
wheel rotates freely.  Recheck the wheel if 
the brake drags or if the wheel does not 
rotate freely. 
7.(NC700SD only)
Install the parking brake caliper and 
tighten the mounting bolts.
u...

107continued
Troubleshooting
Electrical Trouble
Battery Goes Dead
Charge the battery using a motorcycle 
battery charger.
Remove the battery from the motorcycle 
while charging.
Do not use an automobile-type battery 
charger, as these can  overheat a motorcycle 
battery and cause permanent damage.
If the battery does not recover after 
recharging, contact your dealer.
Burned-out Light Bulb
Follow the procedure below to replace a 
burned-out light bulb.
Turn the ignition switch  to the OFF or LOCK...