honda cr v 19997 2000 User Manual
Here you can view all the pages of manual honda cr v 19997 2000 User Manual. The Honda manuals for Automobile are available online for free. You can easily download all the documents as PDF.
Page 931
Bleeding CAUNON: . Do not spill brake tluid on the vehicle. it may damage the paint; if brake fluid does contaqt th€ paint, wash it otf immodiately with water. . Maks sure no dirt oy other forsign matter is allowsd to contaminate the brake fluid. NOTE: . Do not reuse the drained fluid. . Always use Genuine Honda DOT 3 Brake Fluid. Using a non-Honda brake fluid can cause corrosion and decrease the life of the svstem. . The reservoir on the master cylinder must be at the MAX (upper) level mark at the...
Page 932
![Page 932
Inspection and Adjustment
Brake System Indicator
Circuit Diagram lNuLR.HorJDGNrT 0llSt!ITCHUNDEB.DASHFUSE]NEtAY BOIrllA Nl] 42 4!A
PAFK NC BRA(E S\IICH
GBNiBEO
Io\lt j I ERAKE tuU 0 rEVEr 9!1 I(N
| oPt^rf,1 .r
BIKI-o-:G401
Parking Brake Switch Test
1. Remove the parking brake cover,
2. Disconnect the connector from the parking brakeswitch.
3. Check for continuity between the terminal and bodyground in each position according to the table.
Terminal
Lever Position \
Positive
TerminalBody Ground
Lever...](http://img.usermanuals.tech/thumb/34/48204/w300_honda-cr-v-19997-2000-service-manual-931.png "Page 932
Inspection and Adjustment
Brake System Indicator
Circuit Diagram lNuLR.HorJDGNrT 0llSt!ITCHUNDEB.DASHFUSE]NEtAY BOIrllA Nl] 42 4!A
PAFK NC BRA(E S\IICH
GBNiBEO
Io\lt j I ERAKE tuU 0 rEVEr 9!1 I(N
| oPt^rf,1 .r
BIKI-o-:G401
Parking Brake Switch Test
1. Remove the parking brake cover,
2. Disconnect the connector from the parking brakeswitch.
3. Check for continuity between the terminal and bodyground in each position according to the table.
Terminal
Lever Position \
Positive
TerminalBody Ground
Lever...")
Inspection and Adjustment Brake System Indicator Circuit Diagram lNuLR.HorJDGNrT 0llSt!ITCHUNDEB.DASHFUSE]NEtAY BOIrllA Nl] 42 4!A PAFK NC BRA(E S\IICH GBNiBEO Io\lt j I ERAKE tuU 0 rEVEr 9!1 I(N | oPt^rf,1 .r BIKI-o-:G401 Parking Brake Switch Test 1. Remove the parking brake cover, 2. Disconnect the connector from the parking brakeswitch. 3. Check for continuity between the terminal and bodyground in each position according to the table. Terminal Lever Position \ Positive TerminalBody Ground Lever...
Page 933
Front Brake Pads Inspection and Replacement 1. Nsvgr u9e an air hose or dry brush to clean brake assemblies. Use an OSHA approved vacuum cleaner to avoid broathing brake dust. Loosen the front wheel nuts slightly, then raise the vehicle, and make sure it is securely supported. Remove the front wheels. Remove the caliper bolt, and pivot the caliper up out of the way. Check the hoses and pin boots for damage and deterioration. CALIPERBOLTCALIPER BODY 3. Remove the pads, pad shims, and pad retainers. INNEB...
Page 934
Front Brake Pads Inspection and Replacement (contdl 9. Apply Molykote M77 grease or Daikalub 528Dgrease to both sides of the pad shims and the back of the pads. Wipe excess grease off the shims. Apply Molykote M77 to both sides of shims. INOICATOR Apply Molykote M77or 0aikalub 528Dto both sides of shim. 10. INNER PAD OUTER PAD lnstall the brake pads and pad shims correctly. Install the pad with the wear indicator on the inside. . When reusing the pads, always reinstall thebrake pads in their original...