Hitachi Storage Navigator Modular 2 User Guide

Installing Navigator 23–9
Hitachi Storage Navigator Modular 2 User’s Guide
4. In the Performance area, click Settings and then click the Data 
Execution Prevention tab.
5. Click Turn on DEP for all programs and services except those I 
select.
6. Click Add and specify the Navigator 2 installer HSNM2-xxxx-W-GUI.exe, 
where xxxx varies with the version of Navigator 2. The Navigator 2 
installer HSNM2-xxxx-W-GUI.exe is added to the list.
7. Click the checkbox next to the Navigator 2 installer HSNM2-xxxx-W-...

3–10Installing Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Installing Navigator 2 on a Sun Solaris operating system
The following procedure describes how to install Navigator 2 on a Navigator 
2-supported version of Sun Solaris. Before you perform the following 
procedure, be sure that the following directories have at least the minimum 
of amount of available disk space shown in Table 3-1.
To perform a new installation for Sun Solaris
1. Insert the Hitachi Storage Navigator Modular 2...

Installing Navigator 23–11
Hitachi Storage Navigator Modular 2 User’s Guide
In this command line:
• [IP address] is the IP address used to access Navigator 2 from 
your browser. When entering an IP address, do not specify 
127.0.0.1 and localhost. For DHCP environments, specify the host 
name (computer name).
• [port number] is the port number used to access Navigator 2 
from your browser. The default, port number is 1099. If you use it, 
you can omit the –p option from the command line.
6. Proceed to...

3–12Installing Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
• [port number] is the port number used to access Navigator 2 
from your browser. The default port number is 1099. If you use it, 
you can omit the –p option from the command line.
4. Proceed to Chapter 4, Starting Navigator 2 for instructions about logging 
in to Navigator 2. 

Starting Navigator 24–1
Hitachi Storage Navigator Modular 2 User’s Guide
4
Starting Navigator 2
After you use the instructions in Chapter 3, Installing Navigator 2 
to install the Navigator 2 software, use the instructions in this 
chapter to start Navigator 2.
The topics covered in this chapter are:
ˆHardware considerations
ˆLogging in to Navigator 2
ˆSelecting a storage system for the first time
ˆRunning the Backup Volume wizard 

4–2Starting Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Hardware considerations
Before you log in to Navigator 2, observe the following considerations.
Verifying your hardware installation
Install your Hitachi Data Systems storage system according to the 
instructions in the system’s hardware guide. Then verify that your Hitachi 
Data Systems storage system is operating properly.
Connecting the management console
After verifying that your Hitachi Data Systems storage system is...

Starting Navigator 24–3
Hitachi Storage Navigator Modular 2 User’s Guide
•  IPv6 https example (IP address must be entered in brackets): 
https://[IP address]:23015/StorageNavigatorModular/Login
You cannot make a secure connection immediately after installing 
Navigator 2. To connect using https, set the server certificate and 
private key (see Setting the certificate and private key on page 10-
8).
3. At the login page (see Figure 4-1), type system as the default User ID 
and manager as the default...

4–4Starting Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Figure 4-2:  Example of Storage Systems in the Arrays Window
5. Under Array Name, click the name of the storage system you want to 
manage. One of the following actions occurs:
•  If the storage system has not been configured using Navigator 2, a 
series of first-time setup wizards launch, starting with the Add 
Array wizard. See Selecting a storage system for the first time, 
below.
•  Otherwise, the storage system uses the...

Starting Navigator 24–5
Hitachi Storage Navigator Modular 2 User’s Guide
After you use these wizards to define the initial settings for your Hitachi 
storage system, you can use Navigator 2 to change the settings in the future 
if necessary.
Navigator 2 also provides the following wizard, which you can run manually 
to further configure your Hitachi storage system:
• Backup Volume wizard - lets you create a local backup of a volume. See 
page 4-19.
Running the Add Array wizard
When Navigator 2 launches,...

4–6Starting Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Figure 4-3:  Add Array Wizard - Search Array Window
Table 4-1:  Add Array Wizard - Search Array Window 
FieldDescription
IP Address or Array Name Discovers storage systems using a specific IP address or 
storage system name in the Controller 0 and 1 fields. The 
default IP addresses are:
• Controller 0: 192.168.0.16
• Controller 1: 192.168.0.17
For directly connected consoles, enter the default IP 
address just for the port to which...