Hitachi Projector CP-X8800 User Manual

71
INPUT menu
ItemDescription
COMPUTER IN The computer input signal type for 
COMPUTER IN port can be set.
Use the ◄/► buttons to select the 
computer input signal type. AUTO  ó SYNC ON G OFF
• Selecting the AUTO mode allows   
you to input a sync on G signal or component video signal from the 
port.
• In the AUTO mode, the picture may be distorted with certain 
input signals. In such a case, remove the signal connector so that 
no signal is received and select the SYNC ON G OFF, and then 
reconnect the...

72
INPUT menu
ItemDescription
RESOLUTION The resolution for the 
COMPUTER IN input signal can be set on this 
projector.
(1)   In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be   
displayed.
(2)   In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.   
Selecting AUTO SETUP will set a 
resolution appropriate to the input 
signal.
(3)   Pressing the ► or  ENTER button when 
selecting a STANDARD resolution...

73
INPUT menu
ItemDescription
PbyP / PinP  
SETUP PinP POSITION
Using ▲/▼ buttons on the remote control changes the position of 
sub area in PinP mode (
56).
PbyP / PinP FRAME LOCK
Select the screen that enables FRAME LOCK function when using 
PbyP or PinP.
LEFT / PRIMARY: Enables FRAME LOCK function for input on left 
screen of PbyP or on primary area of PinP.
RIGHT / SECONDARY: Enables FRAME LOCK function for input 
on right screen of PbyP or on secondary area of PinP. 

74
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
GEOMETRY  
CORRECTION KEYSTONE
Selecting this item displays the KEYSTONE dialog.
For details, see KEYSTONE in  Correcting the distortion(
44).
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be...

75
SETUP menu
ItemDescription
GEOMETRY  
CORRECTION (continued) PATTERN
Select PATTERN with ▲/▼ 
buttons.
Displayed pattern [Off/1/2/3/4/5/6] can be switched with  ◄/► buttons.PATTERN 1: Frame
PATTERN 2: Red Grid
PATTERN 3: Green Grid
PATTERN 4: Blue Grid
PATTERN 5: Vertical 9 steps
PATTERN 6: Horizontal 9 steps
OFF:  Displays the input  signal.
LAMP & FILTER Selecting this item displays the LAMP 
& FILTER menu.
Select an item using the ▲/▼ buttons, 
and press the ► button or the ENTER 
button on the...

76
SETUP menu
ItemDescription
LAMP & FILTER (continued) FILTER TIME
The filter time is the usage time of the air filter, counted after the last 
resetting. It is shown in the 
LAMP & FILTER menu.
Pressing the  RESET button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the filter time, select the OK using the ► button.
CANCEL  ð OK
• Please reset the filter time only when you have cleaned or 
replaced the air filter, for a suitable indication about the air filter.
•...

77
SETUP menu
ItemDescription
PICTURE 
POSITION Using the ▲/▼/◄/►
 cursor buttons selects the desirable picture 
position.
The PICTURE POSITION is not changed if any of the following
cases apply.
・  There is no non-display area (black display or background display) 
or it is not displayed on the screen.
• One of the following messages is displayed on the screen:
"NO INPUT IS DETECTED"
"SYNC IS OUT OF RANGE"
"INVALID SCAN FREQ."
• The BLANK or TEMPLATE function is selected....

78
SETUP menu
ItemDescription
STANDBY MODE Using ▲/▼ buttons switches the standby mode setting between 
NORMAL and SAVING. 
NORMAL  ó SAVING
When SAVING is selected, the power consumption in the standby 
mode is lowered with some functional restriction as below:
• When SAVING is selected, the RS-232C communication control 
except to turn the projector on and the network function are disabled 
while the projector is in the standby mode. If the COMMUNICATION 
TYPE in the COMMUNICATION menu is set to...

79
SETUP menu
ItemDescription
OSD MESSAGE Using the ▲/▼ buttons turns on/off the message function.
NORMAL  ó SILENT 
ó INHIBIT
 
  
 
■SILENT : The following message functions does not work.
“AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ.”
“NOT AVAILABLE”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
The indication of the ZOOM displayed by changing       *While operating from the remote...

80
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
 
ItemDescription
VOLUME Using the ◄/► buttons adjusts the volume of the audio output.
Low  ó High
SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker.
ON  ó OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE...