Hitachi Projector Cp X605 Users Manual

11
Setting up
NOTE  • Be sure to read the manuals for devices before connecting them to the 
projector, and make sure that all the devices are suitable to be connected with this 
product. Before connecting to a PC, check the signal level, the signal timing, and the 
resolution.
- Do not connect LAN port to any network that might have the excessive voltage.
- Some signal may need an adapter to input this projector.
- Some PCs have multiple screen display modes that may include some signals which 
are not...

12
Setting up
Connecting power supply
1.Connect the connector of the power cord to the AC inlet of the projector.
2.Firmly plug the power cord's plug into the outlet. 
WARNING
yPlease use extra caution when connecting the power cord, as 
RUHOHFWULFDOVKRFN
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated for use with the power cord's 
VSHFL¿HGYROWDJHUDQJH
• Never modify...

13
Remote control
Putting batteries
Please load the batteries before using the remote control. If the remote control starts to 
malfunction, replace the batteries. If you will not use the remote control for an extended 
period, remove the batteries from the remote control and store them in a safe place.
1.Slide back and remove the 
battery cover in the direction 
of the arrow.
2.Align and insert the two AA 
batteries according to their 
plus and minus   terminals as indicated in the remote control....

14
Changing the frequency of  remote control signal
The accessory remote control has the choice of the 
mode 1 or the mode 2, in the frequency of its signal. 
If the remote control does not function properly, 
attempt to change the signal frequency.
Please remember that the “REMOTE FREQ.” in 
SERVICE item of OPTION menu (
	46) of the 
projector to be controlled should be set to the same 
mode as the remote control.
To set the mode of the remote control, slide the 
knob of the frequency switch inside the...

15
Using as a wired remote control
The accessory remote control works as a wired remote 
control, when the wired control port at the bottom of the 
remote control connects with the REMOTE CONTROL 
port on the back of the projector via an audio cable with 3.5 
diameter stereo mini plugs. 
When the remote control signal is hard to reach surely to 
the projector in the environment, this function is effective.
Remote control
NOTE  • To connect the remote control with the projector, use an audio cable with...

16
Power on/off
Turning on the power
1.0DNHVXUHWKDWWKHSRZHUFRUGLV¿UPO\DQG
correctly connected to the projector and the outlet.
2.Remove the lens cover, and set the power switch to 
the ON position. 
The power indicator will light up in steady orange (
	63).
Then wait several seconds because the buttons may not 
function for these several seconds. 
(1)
When AUTO ON in OPTION menu is set to TURN ON (	42):
The lamp will only be automatically turned on when the 
Power switch is turned on after the...

17
Operating
Operating
Adjusting the volume
1.Press the VOLUME button on the remote control.
A dialog will appear on the screen to aid you in adjusting the volume.
2.8VHWKHFXUVRUEXWWRQV
x
zWRDGMXVWWKHYROXPH
To close the dialog and complete the operation, press the 
VOLUME button again. Even if you do not do anything, the 
dialog will automatically disappear after a few seconds.
WKHYROXPH
adjustment is disable. Please see the AUDIO item of AUDIO menu. 
(	37)
Temporarily muting the sound...

18
Operating
Searching an input signal
1.Press the SEARCH button on the remote control.
The projector will start to check its input ports in order to 
¿QGDQ\LQSXWVLJQDOV
When an input is found, the projector will stop searching and display the image. 
If no signal is found, the projector will return to the state selected before the 
operation.
RGB 1
Æ RGB 2
Æ M1-D
Æ COMPONENT (Y, CB/RB, CR/BR)
Æ S-VIDEO 
Æ VIDEO
 MAGNIFYMY BUTTONVOLUME
ON 1
   MUTE
OFF 2
FREEZE KEYSTONE SEARCH
Selecting an input...

19
Adjusting the zoom and focus
1.Use the zoom ring to adjust the screen size. 
2.Use the focus ring to focus the picture.
Operating
Focus ring
Zoom ring
Adjusting the lens shift
1.Use the vertical lens shift dial to shift 
the picture upward or downward. 
2.Use the horizontal lens shift dial to 
shift the picture left or right.
Using the automatic adjustment feature
1.Press the AUTO button on the remote control. 
€For an RGB signal
The vertical position, the horizontal position, the horizontal 
phase...

20
Adjusting the position
1.Press the POSITION button on the remote control.
The “POSITION” indication will appear on the screen.
2.8VHWKHFXUVRUEXWWRQV
x
z
{
yWRDGMXVWWKHSLFWXUH
position.
When you want to reset the operation, press the RESET button on the remote 
control during the operation.
To complete this operation, press the POSITION button again. Even if you do 
not do anything, the dialog will automatically disappear after a few seconds.

”
When this function is performed on a video...