Hitachi Projector CP-WU13K User Manual

							41 OSD Menu description
Main Select
When you want to project PIP image, use this function to 
specify the image source for the PIP image. This function is 
identical to Input Selection; for more information.
PIP Select
Use this function to select the source  for the sub window.  
You can choose from HDMI1, HDMI2, RGB D-15, YUV1 
RGBHV/YUV2 and SDI/HDSDI/3G.
PIP Position
You can choose to display 
the sub window  in 
%


	

%

	
picture according to your preference.
    
  
  
PIP




	

	>

	
	

	



						

							42OSD Menu description
LAMP
This chapter covers information on the projector lamp.
Mode
#
ECO 
  
When set to Eco mode, the wattage of the lamp will be at 360W. If the surrounding environment 



	






=


&
>

	



	


						

							43 OSD Menu description
High Altitude Mode
Use this function to control the projector's cooling fan. You can set it to Off or On. The default setting 
is Off. 
 
Under normal circumstances, the projector will operate normally with this function set to Off.  By 
default, the projector will detect the temperature of the surrounding environment to regulate the speed 
of the cooling fan. When the ambient temperature rises, fan speed will increase (generates louder 
noise) to make sure the heat inside the projector gets discharged and keep the projector working 
normally.  
However, if you were to operate the projector in environment of excessive heat or in areas of high 
altitude, the projector may automatically shut down. When this happens, you can enable this function 
by setting it to On to force the cooling fan to work at a higher speed to regulate the temperature inside 
the projector.
#
High altitude region refers to area with elevation over 1500 meters (4900 feet).
#
When operating in normal altitude environments, the projector will adjust the cooling fan 
 according to the temperature of the working environment. When the temperature rises    
above 30C, the projector will automatically increase fan speed.
#

]




	
>

	$
	

	







	

[email protected] means that you should not be operating the projector in high altitudes when the 
working environment is over 25C. 
(Due to the air thinning substantially at high altitudes, the result of cooling achieved by the cooling 
	

	


	

	


%

{


	


and high operating temperature, the cooling fan will not be able to disperse the heat adequately)
Power
This function will not be available if you have set the lamp to Eco or Normal modes, you can only 
adjust this setting when the lamp has been set to ”Power”. You can specify the lamp power in the 
range of 78% ~ 100%. Generally speaking, the lower the power, the dimmer the image will be but the 
lamp will have longer lifecycle. In contrast, the higher the power, the brighter the image will be at the 
cost of shorter lamp lifecycle.
Lamp1 Status
This function is limited to display purposes to inform the user of Lamp1 status (On or Off ).
Lamp2 Status
This function is limited to display purposes to inform the user of Lamp2 status (On or Off ).
Lamp1 Run Time
This function is limited to display purposes to inform the user of Lamp1's total run time.
Lamp2 Run Time
This function is limited to display purposes to inform the user of Lamp2's total run time. 
						

							44OSD Menu description
ALIGNMENT
Rear Projection
The default setting is Off.
When you have set up the projector for rear projection, please set it to ON. For more information on 
different modes of projection, 
refer to  " Page 18 : Modes of installation ".
Ceiling Mode
The default setting is Off.
When you have set up the projector for ceiling mode (hung from the ceiling in reverse), please set 
it to ON. For more information on different modes of projection, 
refer to " Page 18 : Modes of 
installation ".
Lens Control
#
Zoom 
  
This function is identical to the one covered in previous sections. Refer to " Page 16 : 6. 
Adjusting focus and zoom. ".
#
Focus 
 This function is identical to the one covered in previous sections. 
Refer to " Page 16 : 6. 
Adjusting focus and zoom. ".
#
Shift 
  This function is identical to the one covered in previous sections. 
Refer to " Page 16 : 5. 
Adjusting the projector's angle ".
Dynamic Contrast
[









	
	
	
	

	

	




upon start up or shut down. When activated, the projector will dynamically adjust the image contrast 
from the beginning of the projection until the content has ended. 
						

							45 OSD Menu description
Gamma
Different Gamma settings will affect viewers' perception of the image. Generally speaking, for images 
that are darker, it is recommended that Gamma be set higher to yield better image quality in darker 

&
	

	

&

		


	
>



&

	>

	
set the Gamma lower to give up details in the darker areas to make the brighter areas (i.e. clouds) 
more visible.

						

							46OSD Menu description
Warp
The function provides distortion correction on projected images.
Horizontal Keystone 

 

						

							47 OSD Menu description
Top Right Corner  







						

							48OSD Menu description
Edge blend 
The function of Edge blend is applied in multiple projectors that are projecting at the same screen 
simultaneously to adjust the uniformity of the images on the screen.
#
Status 
 Press ENTER to select ON or OFF. The function must be set to ON in order to enable the   
function of Edge blend. If the function is set to OFF, the function of Edge blend is disabled.
#
White Level


%
















	


 
$


						

							49 OSD Menu description
#
Adjust Lines 
 
When the function is ON, there will be adjust lines on the image in order to easily adjust   


	


						

							50OSD Menu description
CONTROL
IR Address
[








+