Hitachi Projector CP-D10 User Manual

11
Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult...

12
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:
60 degrees (30 degrees to the left and right of the 
sensor) within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the...

13
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTON
POSITION
12
ESCENTERMENURESET
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
      UPVOLUME
DOWNo ONOFF
9× FREEZE
Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency, Mode 1:NORMAL and Mode 2:HIGH. If the remote 
control does not function properly, attempt to change the 
signal frequency.
In order to set the Mode, please keep pressing the 
combination of the two buttons...

14
Power on/off
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
59). Then remove the lens 
cover.
3.Press the STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and the POWER  
indicator will begin blinking in green. When the power  
is completely on, the indicator will stop blinking and light in steady green 
(
59).
Power on/off
To...

15
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/- buttons to adjust the volume. 
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  When 
 is selected for current picture input port, the volume 
adjustment is disabled. Please see the AUDIO SOURCE 
item of the AUDIO menu (
36).
●  When the projector is in the standby state, the volume can be  
adjusted if 
 is not selected for...

16
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTON
POSITION
12
MENU
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
      UPVOLUME
DOWNo ONOFF
9× FREEZE
Operating
1.Press the VIDEO button on the remote control.  
Each time you press the button, the projector switches its 
input port from the current port as below. Selecting an input signal (continued)
●   While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially 
till an input signal is detected...

17
1.Press the ASPECT button on the remote control.   
Each time you press the button, the projector switches the 
mode for aspect ratio in turn. 
Selecting an aspect ratio
● The ASPECT button does not work when no proper signal is inputted.
● The NORMAL mode keeps the original aspect ratio setting.
●  The on-screen menu might be displayed outside of the image display 
area depending on the adjustment value of the ASPECT, D-ZOOM and 
KEYSTONE. Changing the values of ASPECT, D-ZOOM and KEYSTONE 
may fix...

18
Operating
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the 
elevator feet to place the projector horizontally. 
Using the feet can also tilt the projector in order to project 
at a suitable angle to the screen, elevating the front side of 
the projector within 3
degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is 
adjustable while pushing the elevator button on the same side as it.
1.Holding...

19
Operating
1.Press the POSITION button on the remote control while no 
menu is on screen, to display the D-SHIFT dialog on screen.
Adjusting the position
2.Use the ▲, ▼, ◄ and ► buttons to adjust the picture position.
Press the POSITION button again to finish this operation.
●  This is a function to shift the position of the shrunken picture by the D-ZOOM 
function.
●  When an OSD (On Screen Display) menu is displayed, this operation moves 
the position of the OSD menu, but the picture position is not...

20
Operating
• The MAGNIFY dialog will automatically disappear in several seconds with 
no operation. The dialog will appear again if the MAGNIFY ON button is pressed 
when the dialog has automatically disappeared.
• While the MAGNIFY dialog is displayed, press the MAGNIFY ON button to switch 
the dialog between magnifying area shifting (with the triangles) and magnification 
ratio adjustment (with the magnifying glass icon).
• The magnification is automatically disabled when the displaying signal or its...