Hitachi Projector CP-A221N User Manual

41
INPUT menu
ItemDescription
RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input 
signals can be set on this projector.
(1)   In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be   
displayed.
(2)   In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.   
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3)   Pressing the ► or ENTER button when 
selecting a STANDARD...

42
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
D-ZOOM Using the ◄/► cursor buttons adjusts the magnification ratio.
Small  ó Large
• The on-screen menu might be displayed outside of the image 
display area depending on the adjustment value of the ASPECT, 
D-ZOOM, 
 KEYSTONE and...

43
SETUP menu
ItemDescription
PICT. POSIT. H(CP-AW251N)Using the ▲/▼ cursor buttons selects the horizontal picture
position.
LEFT  ó MID 
ó RIGHT
The PICT. POSIT. H is not changed if any of the following cases 
apply.
• The ASPECT is set to 16:9 or 16:10.
• The input signal has an aspect ratio of 16:9, 16:10 or verticallly
smaller than 16:10, while ASPECT is set to NORMAL.
• Horizontal size of the displayed image is full on the effective
display area, while the ASPECT is set to NATIVE.
• One of the...

44
SETUP menu
ItemDescription
PERFECT FIT This item allows you to adjust the shape of the projected image in
each of the corners and sides.
(1) Choose a corner or side to adjust 
using the ▲/▼/◄/► buttons and press 
the ENTER or INPUT button.
(2) Adjust the distortion as below. Use 
the ▲/▼/◄/► buttons to adjust the 
position of the corner. Use the ▲/▼ 
buttons to adjust the distortion of the 
top or bottom side, after defining the 
adjusting position with the ◄/► buttons.
Use the ◄/► buttons to adjust...

45
SETUP menu
ItemDescription
ECO MODE Using the ▲/▼ buttons changes the eco mode setting.
NORMAL  ó ECO
• When the ECO is selected, acoustic noise and screen brightness 
are reduced.
• When AUTO ECO MODE  (
44) is set to ON, the projector will 
always be set to Eco mode at start-up regardless this setting.
MIRROR Using the ▲/▼ buttons switches the mode for mirror status.
NORMAL 
ó H:INVERT 
ó V:INVERT 
ó H&V:INVERT
     
If the Transition Detector is on and MIRROR status is changed, 
TRANSITION...

46
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
ItemDescription
VOLUME Using the ◄/► buttons adjusts the volume.
Low  ó High
SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker.
ON  ó OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE While the image...

47
AUDIO menu
ItemDescription
HDMI AUDIO Using the ▲/▼ buttons switches the mode for the HDMI
TM audio.
Check  each  of  the  two  modes  provided  and  select  the  suitable  one 
for your HDMI
TM audio device.
1  ó  2
MIC LEVEL
Using the ▲/▼ buttons switches the input level to match that of the 
microphone connected to the 
MIC port.
HIGH  ó LOW
HIGH: for a microphone with an amplifier. 
LOW:  for a microphone without an amplifier.
MIC VOLUME
Using the ◄/► buttons adjusts the volume of the microphone...

48
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
LANGUAGE Using the ▲/▼/◄/►
 buttons switches the OSD (On Screen 
Display) language.
ENGLISH  ó FRANÇAIS 
ó DEUTSCH 
ó  ESPAÑOL
       
  (shown in the LANGUAGE dialog)  
Press the ENTER or INPUT button to save the language...

49
SCREEN menu
ItemDescription
MyScreen This item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
1.  
Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from 
the current screen.
Please wait for the target image to be displayed, and press the 
ENTER or INPUT button when the image is displayed. The...

50
SCREEN menu
ItemDescription
MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON  ó OFF
When the ON is selected, the item MyScreen is locked. Use this 
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 73).
MESSAGE Using the ▲/▼ buttons turns on/off the message function.
ON  ó OFF
When the ON is selected, the following message function works. “AUTO IN PROGRESS” while...