Hitachi Projector BZ-1 User Manual

11
Connecting with your devices (continued)
(continued on next page)
• Before connecting the projector to a computer, consult the computer’s 
manual and check the compatibility of the signal level, the synchronization 
methods and the display resolution output to the projector. 
-   Some signal may need an adapter to input this projector.
-   Some computers have multiple screen display modes that may include some 
signals which are not supported by this projector.
-    Although the projector can display...

12
COMPUTER IN1
COMPUTER IN2HDMIUSB TYPE B
S-VIDEO
VIDEOAUDIO OUT
AUDIO IN3
AUDIO IN1
AUDIO IN2MIC
MONITOR OUT
CONTROL
     USB
TYPE A   DC5V 
     0.5A
     LAN
R LRGB IN
L
R
R
L
Connecting with your devices  (continued)
Setting up
•  If you insert a USB storage device, such as a USB memory, into the USB TYPE 
A port and select the port as the input source, you can view images stored in the 
device (
87).
•    You can connect a dynamic microphone to the  MIC port with a 3.5 mm mini-plug. 
In that case,...

13
COMPUTER IN1
COMPUTER IN2HDMIUSB TYPE B
S-VIDEO
VIDEOAUDIO OUT
AUDIO IN3
AUDIO IN1
AUDIO IN2MIC
MONITOR OUT
CONTROL
     USB
TYPE A   DC5V 
     0.5A
     LAN
RS-232CLAN
L
R
R
L
Connecting with your devices  (continued)
To use network functions of the projector, connect the LAN port with the 
computer's LAN port, or with an access point that is connected to the computer 
with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, 
also connect the  CONTROL port and an RS-232C port of the...

14
Setting up
Connecting to a power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
Please remember that when the DIRECT 
POWER ON function activated (
56), the 
connection of the power supply make the 
projector turn on.
►Please use extra caution when connecting the power cord, as 
incorrect or...

15
Using the security bar and slot
A commercial anti-theft chain or wire up to 
10 mm in diameter can be attached to the 
security bar on the projector.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
►Do not use the security bar and slot to prevent the projector 
from falling down, since it is not designed for it. WARNING
►Do not place anti-theft chain or wire near the exhaust vents. 
 
It may become too hot.  CAUTION
• 
The security...

16
Using the cable cover
Utilize the cable cover as the guard and blind for the connecting parts.
1. Connect the signal cables and the power cord to the projector first.
2. Combine parts as shown in figure,  
and assemble the cable cover. 
3 . Insert the three knobs on the cable cover into the three holes on the projector 
as shown in the figure. Pass the cables through the holes on the bottom of 
the cable cover. 
1
2
3
1
2
3
knobs
Setting up
►Be careful not to pinch the cables in the cable cover, to...

17
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the...

18
USB TYPE B
Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control 
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of 
two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse 
and keyboard of the...

19
Exchanging the tip of  the pen
When the tip of the pen is shortened due to wearing, 
exchange it according to the following procedure. 
1. Remove the tip of the pen referring to the 
illustration.
2. Fit a new tip into the place and push it so that it 
clicks.
Installing the batter y
1. Turn the battery cover of the pen to the left to open 
it.
2. As illustrated in the diagram, insert the AAA battery 
into the battery cover with the - end facing the front.  
(HITACHI MAXELL or HITACHI MAXELL ENERGY,...

20
Power on/off
1.Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
111).
3.Confirm that there is nothing that the lens 
door hits while opening. Press  STANDBY/
ON button on the projector or the 
remote control. The lens door opens, the 
projection lamp lights up, and the POWER  
indicator begins to blink green. When the 
power is completely on, the indicator will 
stop...