Hitachi L42vp01u Instructions For Use

							
 English   - 30 -
DISPLAY
Size/Diagonal42 (16:9 Display)
Viewable size / Diagonal 93.02 x 52.32 (cm) / 106.73 (cm)
VIDEO ST ANDARDS
Video  PAL/NTSC/SECAM
TV Tuner (Analog) PAL/SECAM/B/G D/K K I/I L/L
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
CABLE TV (S1-S20 / S21-S41)
100 PRESET CHANNELS
TV Tuner (Digital) MHEG-5 ENGINE compliant with ISO/IEC 13522-5
Ukengine Profile 1
Object carousel support compliant with ISO/IEC 135818-6 and UK DTT profile
Frequency range: 470 MHz - 858 MHz
Transmission standard: DVB-T. MPEG-2
Demodulation: COFDM with 2K/8K FFT mode
FEC: all DVB modes
Video: MP@ML, PAL, 4:3/16:9
Audio: MPEG Layer I&II 32/44.148kHz.
Formats 4:3, Panoramic, 14:9 Zoom, Cinema, 16:9 Subtitle, Auto, Full
AUDIOGerman + Nicam Stereo
FREQUENCY RANGE PC
Horizontal  Frequency:64 Khz (max)
Vertical Frequency: 75 Hz (max)
Clock Frequency: 108 Mhz (max)
Resolutions: 1360 x 768 (max)
Formats: 4:3, 16:9
INPUT  CONNECT IONS
PCD-SUB 15 (VGA)
VIDEO TV TUNER: IEC 75 Ohms input resistance
SCART1: CVBS, RGB
SCART2: CVBS, S
CVBS: 1 x RCA
Y/C (S-Video) MiniDIN
YPbPr: 3 x RCA
HDMI x 2: Multimedia Interface
AUDIO SCART1: Audio L/R
SCART2: Audio L/R
Y/C or CVBS: Audio Phono L/R
YPbPr: Audio Phono L/R
PC: Audio Phono L/R
Headphones: 3.5mm Jack Stereo
Specifications
IB-ENG-(L42VP01U)-MB26 UK-42780W -(RRC1001-2511E)-(ECO PIP)-10052018-50121775.p6516.01.2008, 17:4230
 
						

							
English   - 31 -
RS232 In9 pin mini D-sub
OUT PUT  CONNECT IONSLine OutAudio Phono L/R
Subwoofer 1 x Phono (Mono)
SPDIF Digital Out 1 x Phono
Audio Speaker Output 2x8 W RMS
Synchronization Sync on green, composite sync with automatic detection
separate H and V sync.
Operator Control KeysOn/Off, Standby, Vol+, Vol-, Prog +, Prog -, Menu, TV/AV.
OPERAT ING CONDIT IONSTemperature0°C ~40°C (in operation)
Air Humidity 20%~80% (no condensation)
Atmospheric Pressure 800~1114 HPa 
POWER SUPPLYVoltage Supply220-240V AC
Mains Frequency 50Hz
Power Consumption 235W, 1 W  (Standby)
DIMENSIONS AND WEIGHTDisplay with stand D x L x H: 270 x 1036 x 750 (mm)
Display without stand: D x L x H:  125 x 1036 x 698 (mm)
Weight Display: 24.5 kg
Weight Stand:   3.5 kg
Weight (net):    28 kg
Specifications
IB-ENG-(L42VP01U)-MB26 UK-42780W -(RRC1001-2511E)-(ECO PIP)-10052018-50121775.p6516.01.2008, 17:4231
 
						

							 English   - 32 -
Signal  Input
PC RGB Terminal (D-sub 15-pin connector)
Pin Input signal
1 R
2 G or sync on green
3 B
4 No connection
5 No connection
6 R.GND
7 G.GND
8 B.GND
9 No connection
10 GND
11 No connection
12 [S DA]
13 H.s ync or H/V c omposite sync
14 V.sync.  [V. CLK]
15 [SCL]
• When different kinds of input signals are simul-
taneously  input  to  the  monitor  via  a  graphics
board or the like, the monitor will automatically
select the signals in the following priority order:
Sync signa l type Priority
H/V separate sync. 1
H/V composite s ync. 2
sync.on Green * 3
• Even in the case of the recommended signals
shown  on  the  following  page,  there  may  be
instances  when  correct  display  is  not  pos-
sible. In this case, use H/V separate sync, H/
V  composite  sync.
S-input connector pin specifications
Pin Input signa l
1 Y 
2 Y-GND
3 C 
4 C-GND
Frame GND
HDMI connector pin specifications
PinInput signa l PinInput signa l1TMDS Data2+ 11TMDS Clock Shield
2 TMDS Data2 Shield 12TMDS Clock-
3 TMDS Data 2- 13CEC
4 TMDS Data 1+ 14Reserved (N.C. on devic e)
5 TMDS Data1 Shield 15SCL
6 TMDS Data1- 16SDA
7 TMDS Data0+ 17DDC/CED Ground
8 TMDS Data0 Shield 18+5V Power
9 TMDS Data0- 19Hot Plug Detect
10 TMDS Clock +
SCART connector pin specifications
Pin I nput signa l Pin Input signa l1AUDIO OUT (RIGHT) 12Not used
2 AUDIO IN  (RIGHT) 13RGB-R GND
3 AUDIO OUT (LEFT/MONO) 14GND
4 AUDIO GND 15RGB-R / S.VHS CHROMINANCE IN
5 RGB-B GND 16BLANKING  SIGNAL
6 AUDIO IN (LEFT/MONO) 17COMPOSITE VIDEO GND
7 RGB-B IN 18BLANKING SIGNAL GND
8 AUDIO / RGB SWITCH / 16:9 19COMPOSITE VIDEO OUT
9 RGB-G GND 20COMPOSITE VIDEO / S.VHS LUMINANCE IN
10 Not used 21GND / SHIELD (CHASSIS)
11 RGB-G IN
Specifications
IB-ENG-(L42VP01U)-MB26 UK-42780W -(RRC1001-2511E)-(ECO PIP)-10052018-50121775.p6516.01.2008, 17:4232
 
						

							English   - 33 -
Appendix A: PC Input Typical Display Modes
The display has a maximum resolution of 1360  x 768, frequency range of 56-85 Hz.
The following table is an illustration of some of the typical video display modes.
M o d e Re s o lu tio n F r e q u e n c y
Ho rizo ntal V e rtic alHo r.(kHz)V e r.(Hz)
16 40 4 803 1,5 60
26 404 803 7,9 72
36 404 803 7,5 75
48 006 003 5,2 56
58 006 003 7,9 60
68 006 004 8,1 72
78 006 004 6,9 75
88 006 005 3,7 85
910 247 684 8,4 60
1010 247 685 6,5 70
1110 247 68 6075
1212 801 02 4 6460
1312 80 7 684 7,8 60
1413 607 684 7,7 60
IB-ENG-(L42VP01U)-MB26 UK-42780W -(RRC1001-2511E)-(ECO PIP)-10052018-50121775.p6516.01.2008, 17:4233
 
						

							 English   - 34 -
Appendix B: AV and HDMI Signal Compatibility
SourceAvailable
O
O
O
O
O
O
O
O
480I 60HzO
480P 60HzO
576I50HzO
576P 50HzO
720P50HzO
720P60HzO
1080I50HzO
1080I60HzO
O
O
O
O
480I 60HzO
480P 60HzO
576I60HzO
576P 60HzO
720P60HzO
720P50HzO
1080I50HzO
1080I50HzO
1080P 50HzO
1080P60HzO
1080P 24 HZO
AV-5            
(S-Video)
PAL 50/60
NTSC 60
HDMI1 
HDMI2 AV-3 
(YPbPr)
AV-4   
(FAV)
PAL 50/60 NTSC 60
AV-2 
(SCART -2)
PAL 50/60 NTSC 60
S-VHS 50
S-VHS 60
Supported Signals
AV-1 
(SCART  1)
PAL 50/60
NTSC 60RGB 50
RGB 60
Note: In some cases a signal on the LCD TV may not be displayed properly. The problem
may be a inconsistency with standards from the source equipment (DVD, Set-top box, etc…). 
If you do expereince such a problem please contact your dealer and also the manufacturer
of the source equipment.
(X: Not Available, O: Available)
IB-ENG-(L42VP01U)-MB26 UK-42780W -(RRC1001-2511E)-(ECO PIP)-10052018-50121775.p6516.01.2008, 17:4234
 
						

							
English   - 35 -
Appendix C: Main and PIP-PAP Picture Combinations
MAINAV-1AV-1 AV-2AV-2AV-3 AV-4AV-5 HDM I 1HDM I 2
CVBS RGB CVBSRGBYPBPR CVBSSVHS
PIP ,PAP     
O
AV-1OCVBSAV-1ORGBAV – 2OCVBSAV– 2ORGBAV-3XYPBPRAV-4OCVBSAV-5OSVHSHDMI 1X
HDMI 2XXXXXXXX
PC RGB XX XX XX XX X
(X: Not available, O : Available)
* DTV pip-pap options  are the same as the TUNER input.  TV and DTV cannot be in pip-pap mode together. 
XNO  P IP & PA P A VAIL A BLE I F  M AIN  I S  A V-5
N O  P IP & PA P A VAIL A BLE I F  M AIN  I S  A V-6
X O
X XX
X X XX O
O
O O OO O O X
O O OO O OO
X
XX
X X XX O O
O O OX O OO
X
OO
O O OO O
O
O X OO O OO
O
O O XO O
O
O O
 Main and PIP, PAP picture combinations
TUNERPC RGB
TUNER / DTV *OO O O
O O
Appendix D: Source Menu Selction
The following  is a key  to the AV inputs:
Remote Control Source MenuInput Sockets LabellingTV/DTT TVNot applicable
TV/DTT DTTNot applicable 
AV1 AV-1AV1 (scart 1)
AV2 AV-2AV2 (scart 2)
* AV-2S(not marked see note below)AV3 AV-3AV-3 (Y, Pb, Pr,  L, R)
AV4   AV-4AV4 (CVBS)
AV5 AV-5AV-5 (S-VHS)
HDMI1 HDMI-1HDMI-1
HDMI2 HDMI-2HDMI-2
(there is no PC button ) PC RGBPC INPUT
Inputs can be selected by either using the appropriate buttons on the remote control or by selecting an input on
the source menu.
*For AV-2S, select from the menu.
NB. AV-2S can be used by the use of an S-VHS to scart converter plug (not supplied) or a device which has
scart  ouput  with  S-video  can  be  connected
PC can only be selected using the source menu.
IB-ENG-(L42VP01U)-MB26 UK-42780W -(RRC1001-2511E)-(ECO PIP)-10052018-50121775.p6516.01.2008, 17:4235
 
						

							 English   - 36 -
UK Guarantee
Your Guarantee of Excellence
Thank you for purchasing this Hitachi Television.
In the unlikely event that this product should develop a fault, we undertake to replace or repair any part of the
product  which  fails  due  to  a manufacturing  defect  within  12  months  of  the  date  of  purchase  provided  that:
i) The product has been installed and used only in accordance with the instructions supplied with the product
ii) The product has not been repaired, maintained, or modified by any person other than an Hitachi authorised
engineer
iii)  The product serial number has not been removed or altered
This guarantee does not apply to product acquired second hand or for commercial or communal use
This  guarantee  does  not  cover  the  replacement  of  exhausted  batteries,  the  adjustment  of  user  controls,  or
aerial alignment.
Any parts replaced under this guarantee shall become the property of Hitachi Europe Ltd.
Please note that evidence of the date of purchase will be required before any service under this guarantee is
carried  out.
THIS GUARANTEE DOES NOT AFFECT YOUR STATUTORY RIGHTS.
IN ALL CASES OF DIFFICULTY PLEASE CONSULT YOUR HITACHI DEALER
IB-ENG-(L42VP01U)-MB26 UK-42780W -(RRC1001-2511E)-(ECO PIP)-10052018-50121775.p6516.01.2008, 17:4236
 
						

							ANT.IN
VCR
AV- 1
AV- 2
QUICK GUIDE
QUICK GUIDE
IMPORTANT - If placing TV into cabinet or alcove, ensure there is at least a 100mm (10cm) gap to the 
sides, rear and top of the TV. This is to allow for adequate ventilation during operation. Please 
read the main Users Guide for more safety information before installation.
insert the batteries into your handset
either connect the aerial straight to your TV...
...or connect the aerial through a VCR...
Aerial (RF) Socket Aerial (RF) Socket
wall
socketwall
socket
Aerial (RF) 
Lead Aerial (RF) 
Lead
Optional Scart Lead
TV to VCRAerial (RF) Socket VCR (RF) connector
lead VCR to TV
TFT-LCD TV
Rear view
+
+
-
-
  It is recommended that a scart lead should be fitted between your TV and VCR to enhance your picture and sound 
quality. Scart leads are essential if you have a stereo TV and VCR and wish to obtain stereo sound from your 
equipment. These leads can be purchased from your
 Hitachi dealer or any good High Street electrical retailer.
 
						

							...or through a HDMI and YPBPR products (DVD-RW)
...or through DVD-R,VCR and satellite decoder.
ANT.IN
ANT.IN
RF Lead to 
Aerial  RF Lead 
from VCR to 
SatelliteRF Lead from 
VCR to TV
Satellite LNB lead  Aerial 
VCR
  Scart Lead to 
  AV on TV. -1
AV- 1 TV VCR
AV- 2
DVD RECORDER
TFT-LCD TV
COMPONENTY
PRPBANT.IN
ANTENNA
HDMI OUT
(RF) connector
lead Device to TV
wall
socket
Aerial (RF) 
Lead
Aerial (RF) Socket
  High DefinitionYour LCD Television is capable of displaying High Definition pictures from devices such as a High Definition Satellite Receiver or DVD 
Device.These devices must be connected via the HDMI socket or Component Socket. These sockets can accept either 720p or 1080i 
signals. . Also 1080 progressive mode can be available if
 your TV model supports Full 
HD (Optional).S witch to these sources from the  Source Menu
TFT-LCD TV
  Scart Lead to 
  AV on TV. -1  HDMI Lead to 
  HDMI2 on TV
 
						

							connect the TV plug to the mains socket
switch your TV on
by pressing the On/Off button
NB: When the set is first switched on, the set will be in standby 
. Press the channel up down (P- and the indicator
        on the front of the set will illuminate red , P+)
        or numeric buttons (1, 2, 3, ...) to operate.
insert plug...
European
plug
...and switch on
insert plug...
UK plug
Power Cord 
InputPower on/off 
button
Plug the mains lead
into the TV...
basic functions of remote control
RGB2
TV/DTT
I/II
MENU
GUIDE
DVD
SATINPUT
RETURN FUNCTION
OK
P
12 3
4
56
78
9
0 AV 1 AV 2 AV 3
AV 4 AV 5
HDMI1
HDMI2
....
+
Programme UpVolume Up
Volume DownProgramme Down
To select a programme 
number.
To enter the main menu
For navigation of the menus
To go back to previous menu
220V-240V
AC~50 HzPOWER