Hitachi L26a01a Users Manual

 
 
 
9 
 
 
QUICK START GUIDE (continued) 
 
3. Inser t the batteries into the 
remote control…
 12  
  
4. Removing the Protective 
Sheet 
Before using the TV, remove the 
protective sheet from the cabinet. 
  
5. Switch On… 19  
Press either Power On/ Off switch on the 
unit or Power On/ Off button on the 
remote control. 
●  The color of the indicating lamp turns 
from Red to Green. 
       
6. Auto Tuning ( Language Selection) …22  and 24  
When you turn ON the TV for the first time, your TV...

 
 
 
10 
 
 
COMPONENT NAMES 
Main Unit 
Front Panel     
 
① Cabinet   
② Panel 
③  Remote Control Receiver   
④ Indicating Lamp 
⑤ Speaker 
⑥ Desktop Stand   
⑦  Main Power Switch (on the left side) 
⑧  Sub Power Switch (on the top side)   
 
 
 
Rear Panel   
L26A01A 
 
L32A01A, L37A01A 
 
① Side Input 
②  Power Cord Socket 
③  Terminal Board (External Device Connection) 
④  Control Panel (see below for details) 
Please refer to 
 14 ~ 18   for the detailed information for the connections. 
Control...

 
 
 
11  
 
 
COMPONENT NAMES (continued) 
Remote Control    
 
 Sub Power
  
Press this button to switch TV On or Off standby. 
 Function Select (TV /AV) 
Press this button to select function mode. 
Normally, select “TV”. DTT input is not available.
 
 Program Select [Page Select] 
Press these buttons to select a TV program directly.   
 Freeze [Hold] 
Press this button to change the picture to freeze mode. 
Press it again to return to normal picture.   
(Also, it holds the page in teletext mode.)...

 
 
 
12 
 
 
PREPARATION 
Remote Control Batteries Installation  Handling the Remote Control 
This remote control operates on 2 “AA” batteries. 
1. Open the battery compartment cover 
● Slide open the battery compartment 
cover on the backside in the direction of 
an arrow, and remove the cover. 
2. Installing the batteries 
● Install 2 “AA” batteries (included) making 
sure the polarities match the indication 
inside the compartment. 
 
3. Close the battery compartment cover 
● Make sure of the...

 
 
 
13 
 
 
PREPARATION (continued) 
Safety Precaution on Main Unit Installation   
 
Read SAFETY PRECAUTIONS ( 3 to 6) carefully besides this page.   
The Desktop Stand has been used for the illustration in this manual.   
When installing the main unit, be sure to use the specified mount units in order to obtain maximum performance and 
maintain the safety.   
We assume no responsibility or liability for personal injuries or property damages caused by use of other mount units or 
improper...

 
 
 
14 
 
 
CONNECTION 
Ter minal Positions      
 
Rear  
① Power Cord Socket 
② Aerial Socket 
③ AV1   
④ Service Use Only 
⑤ AV2 
⑥ AV3 
⑦ Monitor Out 
⑧ PC(RGB)/HDMI Analog Audio Input 
⑨ PC Connection Terminal (D-Sub 15 
pin) 
⑩ HDMI   
 
Side 
⑪ Headphone Terminal 
⑫ AV4 
 
Connecting Procedure 
This unit is ready for various kinds of connections. Make a connection in the following steps. Be sure to unplug the power cord 
from the wall socket first, when connecting external equipment.   
1....

 
 
 
15 
 
 
CONNECTION (continued) 
Connecting Procedure (continued)    
3. Connecting to External Equipment   
● Terminals on Rear   
AV1 and AV2 can be connected to the equipment with Component output. 
 
 If your external device has a Component terminal, COMPONENT / AUDIO connection is recommended for higher quality 
picture. 
AV 3 can be connected to the equipment with S-Video output and Composite output. 
 
 If your external device has a S-Video terminal, S-Video connection is recommended for...

 
 
 
16 
 
 
CONNECTION (continued) 
Connecting Procedure (continued) 
Monitor Out can be used to display same image and sound as main unit on another television. 
When this output terminal is connected to an external television with a 75 Ohm terminal, the same image and sound from 
composite (AV3, AV4), or TV signal can be displayed to the external television. 
 
NOTE 
●  Video output is not available from component, RGB, or HDMI input. 
PC connection terminal (D-sub 15 pin) +PC(RGB)/HDMI Analog Audio...

 
 
 
17 
 
 
 
CONNECTION (continued) 
Connecting Procedure (continued) 
NOTE 
●  About PC (RGB)/HDMI analog audio input terminal 
This terminal can be used in one of the following cases only. 
① The external device is connected to the PC (RGB) terminal of the TV. 
②  The DVI output of an external device is connected to the HDMI terminal using the HDMI-DVI cable.  
 
  
Make sure that the video and audio terminals are connected to the same external device. 
About the out put format of an external...

 
 
 
18 
 
 
CONNECTION (continued) 
Connecting Procedure (continued) 
4. Connecting the plug into the wall socket 
Connect the power cord after completing all other connections. 
(The type of plug is different from this drawing for some countries.) 
 
 
   
 
 CAUTION  
 
● Use only the power cord provided.   
●
 Do not use a power supply voltage other than that indicated (AC110-240V, 50/60Hz). It may cause fire or electric 
shock.  
●
 For the LCD panel, a three-core power cord with a ground terminal...