Hitachi Ic35l060avv2070 Manual

							version 1.3
Simple Installation Guide
Hitachi Deskstar
3.5 inch ATA/IDE
This document provides instructions to install your Hitachi 
Deskstar drive in a system. Additional information can be 
found at www.HitachiGST.com/support
Getting Started
IMPORTANT! Back up all data before beginning installation. 
Handling Precautions
Caution: Poor handling, physical impact or electrical shock 
causes most premature hard disk drive failures.
• Set the drive down gently to prevent damage from 
impact or vibration.
• Do not open the ESD bag containing the drive until 
needed. 
• Handle the drive carefully by the edges. Do not touch 
the exposed printed circuit board or any electronic 
components. 
• Do not press on the top or bottom of the drive.
• Do not cover the drive’s breather hole. 
Before handling the hard disk drive, discharge any static 
electricity from yourself and your clothing. With one hand, 
touch an unpainted, metal surface on your computer chassis, 
then touch the ESD bag with the other hand. Remain in con-
tact with the chassis and the bag for a minimum of two sec-
onds. 
Tools for Installation:
You may need one or more of the following items to install the 
Hitachi Deskstar drive:
•  A Phillips head screw driver
•  A flat-blade screw driver
•  A small needle-nose pliers
•  Your system manual
•  Operating system (OS) startup CD or diskette 
Begin Hardware Install
1. Turn off your computer system.
2. Unplug your system.
3. Discharge static electricity (see above).
4. Remove the cover as specified by your system man-
ual.
5. Find the mounting bracket inside the system where 
you will install the Hitachi Deskstar. 6. If you are replacing a hard drive, remove the drive 
from the system.
Note: There are many variations of tower and desktop 
designs. Below is an example of a typical tower design. 
Configure the Jumper settings
1. Remove the drive from the ESD bag. 
2. Record the model (HDS......), part number (P/N) 
and serial number (S/N). 
						

							version 1.3
3. If the new Hitachi Deskstar drive will be the only 
hard disk drive on a cable in your system, jumper 
the drive to Device 0 (MASTER). If you are adding 
the Hitachi drive to a cable with another hard drive, 
jumper the Hitachi drive as  Device 1 (SLAVE). 
Attach the Cables
Note: With some system cases, it may be easier to attach the 
cables after the drive is mounted in the system. 
1. Attach the blue connector of the ATA IDE cable to 
the IDE connector marked Primary or 0 on the 
motherboard or controller card in your system. 
2. Attach a power cable to the hard disk drive.
3. If the Hitachi Deskstar is the Device 0 (MASTER) 
drive, attach the BLACK connector of the ATA/IDE 
cable to the hard disk drive. If the Deskstar is the 
Device 1(SLAVE) drive, attach the GRAY connec-
tor of the ATA/IDE cable to the hard disk drive. 
Mount the Drive
There are many variations of system cases. Hitachi Deskstar 
drive can be mounted with any side or end vertical or hori-
zontal. Do not mount the drive in a tilted position. 
1. Place the drive in an empty drive bay, and line up 
the 4-screw holes. Make sure to use all 4 screws 
when mounting the drive, as a loose drive may 
vibrate when in use and result in drive failure. Con-
sult your system manual for additional information.
2. Check all internal cable connections to ensure they 
are securely seated. 
3. Replace the system cover. 
4. Check all external cable connections to ensure they 
are securely seated. 
5. Plug in your computer.
Begin the Software Installation
1. Confirm the drive is recognized in the System  
BIOS, or, if adding the drive as a Slave, confirm it 
is recognized by the Operating System. Key strokes 
sequences for accessing your BIOS are often dis-
played at boot, or can be found in your computer 
system manual. 
2. Locate drive settings in your BIOS. Verify correct 
detection of drive capacity.  If your BIOS does not 
detect the Hitachi Deskstar, shut down your system 
and review the installation procedure. If your drive 
is still not detected in BIOS, contact the Hitachi 
Global Storage Technologies Support Center:
www.HitachiGST.com/support
Install the Operating System
Once the drive is recognized correctly by the BIOS, it is 
ready to be partitioned, formatted and the Operating System 
installed.  Please consult your Operating System manual for 
information on how to install the Operating System or see 
our Partitioning and Formatting Guide at:
 www.HitachiGST.com/support 
						

							version 1.3
© Copyright Hitachi Global Storage Technologies 
Hitachi Global Storage Technologies
5600 Cottle Road
San Jose, CA 95193
Produced in the United States
5/04
All rights reserved Deskstar™ is a trademark of
Hitachi Global Storage Technologies. 
Microsoft, Windows XP, and Windows are trademarks of 
Microsoft Corporation in the United States, other countries, 
or both.
Other product names are trademarks or registered trade-
marks of their respective companies.
 
References in this publication to Hitachi Global Storage 
Technologies products, programs or services do not imply 
that Hitachi Global Storage Technologies intends to make 
these available in all countries in which Hitachi Global Stor-
age Technologies operates.
Product information is provided for information purposes 
only and does not constitute a warranty.
 
Information is true as of the date of publication and is subject 
to change. Actual results may vary.
 
This publication is for general guidance only.  Photographs 
may show design models.
21 May 2004 
						

							version 1.3