Hitachi Home-1 Projector Quick Guide

1
ProjectorHOME-1    HOME-1   
User User
’ ’
s Manual – Quick Guide s Manual – Quick Guide
Thank you for purchasing this projector.
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual. 
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.NOTE
Your projector should come with the items shown below. Contact your dealer if anything is...

2
Connecting Devices Connecting Devices
Please refer to the following for connecting your devices.
See the rear of the projector and open the ports cover.
You can see the ports.
S-VIDEO AUDIOY
COMPONENT VIDEOCB/PBCR/PR
COMPUTERCONTROL
S-VIDEO AUDIO
Y
COMPONENT VIDEOCB/PBCR/PR
COMPUTERCONTROL S-VIDEO AUDIO
Y
COMPONENT VIDEOCB/PBCR/PR
COMPUTERCONTROL
S-VIDEO AUDIO
Y
COMPONENT VIDEOCB/PBCR/PR
COMPUTERCONTROL
S-VIDEO AUDIO
Y
COMPONENT VIDEOCB/PBCR/PR
COMPUTERCONTROL
S-VIDEO AUDIO
Y
COMPONENT VIDEOCB/PBCR/PR...

Power switch
3
1Connect the connector of the power cord to the AC
inlet of the projector. 

2Firmly plug the power cord’s plug into the outlet.
1Remove the lens cap.
2Set the power switch to [ | ] (ON). 
3Press the STANDBY/ON button of the
projector or the ON button of the
remote control. 
The projector lamp will light up and the
POWER indicator will begin blinking green.
According to a setup, the projector lamp
may light up and the POWER indicator
may begin blinking green, without
pressing this...

4
Adjusting The Projector's Elevator
Using The Picture Shift Dials
CAUTION• To prevent damaging the projector and injuring yourself, ALWAYS
HOLD THE PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
You can use the elevator feet to adjust the angle of projection. The adjustment range of
the elevator feet is 0 to 9 degrees.
Press and hold in the elevator buttons.
2Raise or lower the projector to the desired
height and then release the elevator buttons.
When you release the...

5
See the top of the projector. You can see the control buttons.
Contr Contr
ol Buttons ol Buttons
Pr Pr
eparing Remote Contr eparing Remote Contr
ol ol
POWER indicator
tells the state of power
supply. Refer to the section
“Turning On/Off Power”.
INPUT button
toggles between 
the signal ports.
MENU buttons
operate the menu function.
STANDBY/ON button
prepares for turning the power on/off. Refer
to the section “Turning On/Off Power”.
TEMP indicator
lights or blinks when any
problem about internal...

6
See the remote control. 
Remote Contr Remote Contr
ol ol
OFF buttonprepares for turning the
power off.
SEARCH button  
searches for an input
signal between the
following signal ports of
COMPUTER, VIDEO, 
S-VIDEO and
COMPONENT VIDEO.
MENU button
opens/closes the menu.
S-VIDEO button
selects the input signal
of S-VIDEO port.
COMPONENT
button
selects the input signal of
COMPONENT port.
VOLUME button
turns on/off the VOLUME
mode.
In the VOLUME mode,
To adjust the volume,
use the cursor 
/ 
buttons.
MUTE...

After making sure that the projector has cooled adequately,
slowly flip over the projector, so that the bottom is facing up.
7
Lamp Lamp
WARNINGPlease carefully read the “User’s Manual - Safety Guide”.
The projector uses a high-pressure mercury glass lamp made of glass. The lamp can
break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of
glass to fly into the lamp housing, and for gas containing mercury to escape from the
projector’s vent holes.
• Do not open the lamp...

8
Air Filter Air Filter
WARNING• Please carefully read the “User’s Manual - Safety Guide”.
If the air filter becomes clogged by dust or the like, internal temperature rises and could cause malfunction.
• Use the air filter of the specified type only.Type number: NJ08312
(sold separately)
• Do not use the projector with the air filter and filter cover removed.
CAUTION• Do not reset the filter timer without cleaning or replacing the air filter.
• When you replace the lamp, please replace also the air...